I just bought a set of 2013 20" rims for my 2012 F-250. I can't seem to get the tire fault light to go off. I've gone through the "learn" process but it won't read them. Are the TPMS not the same between years?
View 2 RepliesJust wondering what this could be.its giving me the 50 miles to 50mph max speed. Def tank is half full.truck runs fine.
View 2 RepliesI just bought a new 2014 f250.
He says since he has purchased the truck the TPS sensor would occasionally go off saying there is issues with the tires. Tires are fine yet the light chimes on after being reset shortly. Been at the dealer for a week and they haven't really touched it I was wondering if there is any know issues.
Also my dad had the truck in 4x4 and when he puts the truck in park it made it a loud clunking noise. Ford is said there heavy duty line was full so they didn't look at that ethier. He needs the truck for the weekend so he is picking it up tomorrow, he will return it when he can but does this sound familiar as well?
I had a ford technician plug in and check my CEL. Says P246E, Bank 1 sensor 4, exhaust system fault. I am leaving for holidays in a couple of days but dealer to busy before I leave. Is this something that will leave a guy stranded on the side of the road? I've already been towed once...
View 5 RepliesFinally got back home and I have the TBC Fault occasionally pop up on the dash and sometimes the C2803 fault code (Brake Pressure Transducer Sense Circuit Failure). Both have happened without the trailer connected. Is it the OEM brake controller? Or possibly the sensor at the base of the Brake Master Cylinder?
View 7 Replies2014 F250 Diesel... I got the msg saying 50 miles until speed limited to 50 mph. None of the earlier warnings re adding def. check def on computer and it said it was ok. I even added def and it only took a small amount until it overflowed. It was more than 1/2 full. The error message did not reset. I drove it around for several miles and it still would not reset. Having it services as we speak, and the tech is still having difficulty running down the cause. He has done a regen,and reset the computer and etc and still has not resolved the issue..
View 14 RepliesI bought my 2015 F250 last November, and this spring my check engine light comes on with the message exhaust system fluid fault with the anoyying speed limitation. Bring the truck back to the dealer and they just say add def fluid, so I just have them do it. 2 weeks later the message comes back, bring it back to the dealer and they tell me it "needs reprograming" they do the work, light goes off. two weeks later light comes on again. Dealer puts in new exhaust sensors and reprograms the truck.
This fix lasts a few months in the mean time the truck shutters really bad under regeneration mode. Talk to dealer they claim its normal. Finally this week the light comes back on again. Bring the truck to the dealer and Ford keeps telling them that it only needs reprograming but that doesn't fix the problem. The dealer wants to replace the computer but ford isn't letting them do it (the truck is still under warranty) . I am starting to get pretty mad when I went out and bout a 65k truck not to have these problems.
On a family vacation in our 2013 6.7 pulling a 41ft trailer to the Seattle area from Alberta Canada. Made it to destination yesterday. Woke up this morning started truck and cel on. Bought a code reader at the local napa store and read P206 fault inj 6 open circuit. Any thoughts on driving the truck around with a inj fault? Thought I had read here some where that 6 was the regen cylinder.
View 14 RepliesMy 2012 F350 Lariat has 6100 miles on it now and on the way home tonight I got a "speed limited to 50 mph in 50 miles" message on the display. It states that there is a "diesel exhaust fluid system fault". The def was topped off about 2000 miles ago and the message center says that the fluid level is "ok". I am going to be on the phone with the dealer first thing in the morning. This is my personal/work truck and if I can't tow a trailer then I can't work. My guess would be a faulty sensor. I have no doubts that the dealer will get this resolved quickly as they have been great about everything else. I also want to say that other than this, I am sure minor issue, this truck is awesome!
View 14 RepliesI'm new to owning a diesel. I have a. 2004 f250 6.0. I gotta smog the truck this weekend but the check engine light is on. Fault is P0674. I've notice during the day it starts up fine but at nights, lately it's been low 40 outside it won't start. Where to start at.
View 3 RepliesMy fuel gauge on my Sport Trac is nowhere near accurate. Ran out of gas the other day showing 1/4 tank.
I get a little hesitation as well when accelerating.
I'm showing a PO191 fault code which says Fuel rail sensor.
Would that cause a gauge to malfunction?
When the truck shifts into 5th gear i instantly feel a constant vibration and noise until it shifts to 6th gear. This happens nearly every time while driving at 40mph. Rpm range 1200 - 2000. I bought the truck new on June 30th and noticed the problem on my way to work on Monday July 2nd. Took it to the dealer on July 5th and the tech said it was the torque converter slipping. I drove it home because they didn't have time to work on it. Took it back on July 12th and the dealer has had it since (currently 30 days) They originally told me it was not the engine or transmission and it was an exhaust problem. Last week they said it was the motor mounts and said they would be done.
View 14 RepliesMy 2012 diesel frequently stalls momentarily after I touch the brake. This is very annoying as I drive in heavy traffic and often have to touch the brake then accelerate to merge into freeway traffic. The dealer service department said this was a 'feature' and not a flaw. Is there any way to eliminate this issue?
View 5 RepliesSunday I received the dreaded DEF system fault message on my 2012 CC SRW SB FX4 with 7800 miles on it. Warned me that speed will be reduced to 50 MPH in 50 miles. I have a CTS Insight, so I checked for DTC's. First one was P2200 - NOx sensor circuit (Bank 1, Sensor 1), the second one was P204F - Reductant system performance (Bank 1).
After 50 miles it warned me that speed would be reduced to 50 MPH on next restart. Sure enough, Monday morning speed was limited to 50. I took it to the dealer, but I should have left it running. When the service guy started it, the fault had cleared and it no longer showed the P2200 NOx sensor code, although the P204f code was still there.
My question is, why in the world would Ford make it so that the code is cleared if the fault goes away, especially after putting you through the 50 MPH limit scenario?
Dealer did a reflash and said its OK now, but I'm not so sure. My trucks build date is 10/6/11. I read TSB 11-11-13 which states the NOx sensor module should be replaced for P2200 on trucks built before 10/11/11. Is that only for a persistent P2200?
I'm a new Ford owner and my 2012 F250 is my first diesel. Recently, my truck has been having a problem with the engine loosing power, bogging down, shaking-pinging, every once in a while, like 1-2 times a week. When it happens, I can barely get the truck to do 50 MPH. It sometimes happens when the "cleaning exhaust filter" message is displayed, but also happens when it's not displayed. I recently read on the internet about HPFD failures.
What may be happening to my truck? Could it need Cetane booster? Also, how about scheduled maintenance. The owners manual (diesel supplement) says to do the maintenance once the message center says to change oil soon. The dealers here in AZ are pretty much saying 5 months or 7,500 miles. On my other trucks (which were gas), I would stick to what the owner manuals said because I thought how could they deny a warranty claim if you're sticking to what the manual says.
Have a 2012 F250 4x4. Have read many posts about different lifts etc. I don't want to go real big but I would like to go to a larger tire than the stock Michelins.
On a F250, done a 2 inch front leveling kit and switched out the rear blocks to F350 blocks. Assuming I wanted to put new shocks on with this change, what level kit and what adjustable track bar (from what i've read this is pretty much required).
I have a 2012 F-250 6.7L w/8K miles. I have been struggling with this issue for 6 mo. The engine feels like its missing at low RPM. I would equate it to the feeling of a bad coil pack in a gas engine. The boost indicator drops to 0 for a split second then recovers. The dealer says they can't find the issue but went ahead and replaced the turbo. After the turbo replacement It got worse. This is an intermittent problem with no codes.
View 14 RepliesI am driving a early 2004 F250 CCSB with a 6.0l. I have a Code that is for an EGR Low Flow. I have a Scan Gauge II that I have been using to try and determine why this is. I have replace the EGR Cooler (unrelated), the EGR valve, and the MAF.
My EVD and EVM are tracking. My IA1 reads a letter (B usually) and 3 numbers that are in the 6 to 900 range. My IA2 appears to read normal with atmospheric temps at start up and goes up and down IAW the EVD and EVM readings. My FIA (already programmed) reads outside temperature along with the overhead console. The EBP reading doesn't exist, it is blank.
My son has a 2012 F250 King Ranch, 6.7 L.
Little info: Last Friday the inter-cooler hose blew. We changed the hose this past Saturday. The truck ran great all weekend. Last night leaving for work it started to sputter and then died. Got the truck to crank, ran great no sputter, but something under the hood sounded off. We drove it all the way back home. Killed it, re-cranked it, everything was fine.
This morning cranked the truck, ran fine for 5 min then died and would not crank. We decided it needed new fuel filters. Replaced the fuel filters, truck now cranks and idles great. When you mash the gas at it revs up then sputters like it would die, when you let off the accelerator it catches up and idles fine again. It cant be too much wrong, it ran great all weekend.
I have a 2012 F250 4x4 6.7L Diesel with around 114k miles on it. Jut in the past couple weeks it has produced this issue: At start-up/during warm-up it when I make a turn (left or right) and hit at least 40mph the steering feels heavy and pulling to the right, all of a sudden it seems to release and dart a little to the left. It does this for about 10 miles then it is fine. Steering is a little loose, 114k miles and previous owner had a plow on it but once it straightens out it is fine for the rest of the 45 mile treck. Tires are new Goodrich All Terrains, no visible signs of a belt being broke.
View 2 Replies2012 F250 Lariat with 18k on the clock. FOr the past two months I've had a temporary side job on weekends and had to haul some trailers. I noticed my trailer gain operates sporadically and if I try and adjust it she tells me there's no trailer connected. I've edited the settings and reset all the settings also. I find this particularly annoying when towing the 4,000 lb trailer but I'm also hauling single axle trailers and it hasn't registered that I'm towing once.
View 14 Replies