Ford 6.7L Power Stroke Diesel :: 2012 - Exhaust Smell Coming From Truck - White Smoke
Jun 6, 2017
Today I drove to dinner in my 2012 6.7 with no problems then on the way home my brother said he noticed my truck was white smoking quite a bit and he said there was a very strong exhaust smell coming from my truck ( he was in his car behind me) I ran a diagnostic test and what came up was code P0401 (I believe that's right). Need to figure out what is going on with my truck before I take it to the mechanics and get charged up. The truck still has DPFs in it just has a DPF back exhaust and has a AFE cold air intake running on a stock tune. However I do have the DPF deletes and EGR delete sitting in my garage just haven't gotten them on the truck yet.
View 2 Replies
Advertisement
2005 6.0 & noticed on Friday there was white smoke coming from exhaust that started when I'd turn on truck then aster 1st light or stop sign it would be a cloud of white smoke. Once I start to drive it stopped & I didn't see it again that day. I noticed the same thing again on Saturday & Sunday but the smoke was thicker on these days but would stop like the day before.
I had a code come up a month ago which I believe was P404 but read something about EGR valve. So I replaced the EGR valve 3 weeks ago & light never came back.
Today I had a Dr's Appointment and had usual white smoke in morning but once I got to the Dr's appointment the truck sounded like the turbo got louder then usual and started to see cloud of white smoke again. While sitting in parking lot I check to see any codes but nothing came up but the cloud of smoke started.
When I left my appointment, the turbo sounded louder still and noticed white smoke every single time I stopped at a light or stop sign.. Then the coolant level was high with the engine giving me the warning of over heating coolant or something like that.
View 2 Replies
Having trouble with 6.0 powerstoke white smoke out exhaust. We have installed egr delete and still have white smoke and water coming out of exhaust not as much as before. Took it back apart to see if we did anything wrong everything look ok. We did a compression test on all cylinders they check out ok.
View 6 Replies
I noticed a rough idle after driving an hour with a 6000 lb trailer and stopped at an offramp. Had no performance issues to that point in an hour drive. Then I noticed a good amount of white smoke coming out of the exhaust. The idle felt just like when I had a contribution/balance code on #5 a year ago, and a new injector fixed that. Before long (10-20 minutes later) the idle got real loud, like a big knock/loud tick every revolution.
I had a bunch of stored codes, so I reset them and later found a P0281 - Cylinder 7 contribution/Balance and P0404 - EGR control circuit range/performance were the 2 that came back. I drove it 2 more hours to get home. It ran well under load, but coasting or stopped gave the loud knock, and stopped and idling was a rough, inconsistent idle. It even stalled on me 3 times when braking for a red light (auto trans). There was a lot of white smoke all the time, plus a little dark smoke on acceleration.
What would you recommend for troubleshooting steps? I could put a new injector in #7 and clean the EGR valve, but want to have a good idea that will fix it first. Is there a good chance I have a messed up piston in #7 now?
Codes I cleared:
P0148 Fuel delivery error
P0234 turbo overboost (i know i need to pull and clean the turbo anyway, unrelated to today's issue)
P0281 Cylinder 7 contribution/Balance
P0404 EGR control circuit range/performance
P0670 Glow plug (I had the module unplugged a while ago)
P0683 Glow plug (I had the module unplugged a while ago)
View 14 Replies
2007 F550 with the 6.0. About 2 months ago I replaced the EGR cooler with a Bulletproof cooler. Truck ran well for a few weeks. Then I started getting the "turbo fart". I stopped using the truck until I had an issue with another truck. I was stuck so I sent the 07 out without cleaning the turbo. This morning a decent amount of white smoke started coming out of the exhaust. The smoke would sometimes get a bit gray. Going up hill it didn't have much power at all.
View 8 Replies
I just looked back and it has been since July 7th that my girl has been sitting in my shop. Well this past weekend I finally got her back together and started. It took a while to build pressure but she finally came to life..
While I am thrilled that she is running again i have low power before the boost kicks in and is idling rough with a blueish- white smoke coming out of the exhaust. Once i kick her a little she will get up and go but I've never had the smoke before.
I'm thinking maybe a bad injector???
View 3 Replies
Newbie hear to the 6.0L's. But I'm learning an awful lot really quick from all of you here. I've read lots of tech stuff on these EGR Coolers, oil coolers, FICM tests. This is what I got happening right now.
2004 F-250 6.0L. Today was 45 degrees in Reno. 5400 ft elevation. Tried to start it without block heater. Would not even crank. It tried to crank but sounded like it locked up on first crank. Tried again, nothing. Same. Tried yet again and finally got to getting the engine to crank, but wouldn't start after about 5 seconds of cranking. Waited a little while not wanting to burn out my FICM, then tried again. Same as previous, would crank but not turnover. Checked batteries. Both were over 12.3 V cold, motor not running. This next time, turned key on and let it sit in ON position for about a minute. Then cranked and it took about 5 seconds and then the motor finally cranked over. Lots of black smoke as usual for a cold start like this. Battery volts after cranking over and running were now both over 13.6 V.
Keep in mind the truck has started better than this before in 15 degree weather just about a month ago.
After it started I noticed what appeared to be oil/coolant residue directly underneath trucks transmission area. It was not tranny, but in that area. I got under the truck and can see this fluid coming from EGR Cooler area.
Now for the smoke. Just stared smoking on start up. White smoke. Then it would disappear as engine warmed up. Now its constant white smoke when warmed up and applying the throttle. Smells like coolant coming out of exhaust. Not diesel.
I parked truck facing downwards on my driveway. Then I checked EGR Valve. When I pulled it it was WET. Not dry. Peeked in EGR Valve hole, didn't see coolant. Just wetness. I did change gasket and rings on it the day before as well.
As for FICM, it reads 47.9 Volts on key turn, 48.1 on cranking and 47.8 running. FICM good by all standard 6.0L literature. Degas bottle passed pressure test holding near 15 PSI for 20 minutes! No oil in degas bottle that I can see.
Truck is stock. Is my egr cooler and oil cooler shot? Would a bad egr cooler or oil cooler cause this awful cold start? When I plug in the block heater, it starts NO PROBLEM, but still white smoke. Also, NO loss of power at any time.
View 6 Replies
yesterday I went out started my truck and white smoke started coming out my exhaust so I turned it off waited a bit started it back up let it run for a bit smoke went away drove it about 60 miles. Later that night it did the same thing but I was 2 gallons short on coolant drove it another 60 miles ran fine. Next morning decided to take it to a shop put more coolant in it drove maybe 20 miles to shop got there turned it off everything was fine never over heated once. So this shop is now telling me my trucks hydro locked and I steamed the EGR valve. And there telling me it's gonna be $8000 to fix it .
View 3 Replies
I was passed the other day by a newer (square mirrors) nice-looking Super Duty that was slightly spewing white exhaust smoke. As a life long truck driver, I know a few diesel smells (and I kinda like some ). But, this was so pungent that it was irritating my eyes inside my own cab.
It was so irritating and nasty smelling, that I had to slow down (to let him gain some ground) and open my windows to clear out my truck. So that I may be better informed, what could've caused this?
View 14 Replies
I have a 2006 F350 6.0 litre diesel. The other day I started it up drove away and it was blowing huge plumes of white smoke out of the exhaust. Shut it off.....started it up again after a while then went on a long drive and it went away. What that was?
View 6 Replies
no change, changed stand pipe and dummy plug on driver side, no change and guess what? Now I am stuck on the side of the road waiting to give my last $100 to a tow truck! Engine is hydrolocked, fuel pressure is low, starts off at around 20 and works up to 54 with key on engine off, and that is as much as I know from the side of the road with out my AE. Blew white smoke also. Smelled of unburnt diesel. I think it's linked to my rough running issue. Maybe a bad injector? But every time I did the click test they all passed. Idk, I'm gonna remove the glow plugs and see which hole is loaded and with what. . .
View 14 Replies
After a couple of setbacks, including forgetting to install 3 out of the 4 orings on the oil cooler, I got the IPR Gen2 delete installed. I have a couple of issues since getting it started. I have low boost, I know the up pipe for the turbo is seated well, really surprised about that. However, the exhaust pipe may have a slight leak, but not positive. Finally, the last on this issue, I have a ripped MAP hose that I'm going to replace.
Next issue is that I hear what almost sounds like a gas engine exhaust rumble from the front of the truck. What it could be? I had white smoke initially coming out of the exhaust, but it cleared up after getting everything up to temp and taking it for a ride down the road. On a side note, the leak that I had from my previous thread seems to be gone now.
View 3 Replies
I have a 2006 F350. It started running rough and white smoke from the exhaust. I did an injector buzz test and found no codes. Cylinder contribution check showed cylinder one was not functioning. I replaced number one injector, cleaned injector cup installed new injector and copper washer. Engine runs the same. If it was a wiring harness issue should that have shown up in the buzz test?
View 8 Replies
I just got a 2006 ford F250 lariat fx4,and it's already at the shop.. when cold start it has some white smoke, but once I get up to highway speeds the truck jerks and bucks. turbo is putting out normal boost. I've changed oil and filters along with fuel filters. also put on a new serpentine belt and pulley, air filter and have everything cleaned real good. the truck is acting like it's starving for fuel. FICM or injectors ?
View 14 Replies
My 04 PS was blowin white smoke constantly while running. I just towed a uHaul from Connecticut to Virginia Beach and had some coolant issues on the drive down (I was out of coolant on 95 in PA, added coolant and it made the rest of the drive no problem). I got here to Virginia and it was low on coolant again. I added coolant to it, and now I have some other issues. I had what looked like oil comin out the stacks onto the bed, so I pulled the turbo thinking it was seals. But the turbo was just rebuilt prior to me buying it with a wicked wheel in it. It still had stock EGR and it has 202K on it.
Checked and found EGR valve was wet. Ordered an EGR delete kit, and just finished installing it. Now with everything put back together, the truck doesn't want to start. It cranks but doesn't fire. I pulled the codes from my tuner and I got: P0403, P0405, P0683, and P2623. I know P0403 and P0405 are related to EGR but the others I'm at a loss on. The EGR delete kit I bought included the blank to remove the valve but what do I do with the plug that used to plug into it? Any way forward to get the truck back up and runnin again? This is my daily driver and not lookin to break the bank to get it goin again but I really need her to be reliable.
View 14 Replies
Just happened today right after I bought diesel. thought it may be water in fuel but after researching wondering if it is injector, etc. It starts every time knocks real bad sometimes for a minute, but clears up to idle ok. During idle no smoke, slightest acceleration however produces white smoke harder I accelerate more it plumes and it smells like diesel in the air.
Cannot get past 15 or so mph till switching into 2nd gear then 25mph max. Had to drive 4 miles like this I can say it cleared up and drove 1/2 mile until I had to stop at a traffic light then going from idle to acceleration again ran bad rest of way home another 2 miles.
A few years ago I did have a rough idle and accel. similar and it ended up being the broke pick-up/sending unit in tank (but of course that was when you get to around 1/4 tank of fuel and didn't run bad above that much fuel in tank), plus there was almost or more than a gallon of water in tank. I have done the mod for the fuel pickup with hoses, filter canister, etc. but wondered at first today if I had gotten bad gas or water in the tank again. Not sure how that much water got in the tank to begin with but that was bout 5 or 6 years ago.
Truck has over 200k miles and Ive had it for 11 years. In the morning will check the ICP sensor by unplugging look at fuel filter bowl, etc. A question I have is: Is water heavier than diesel, would it run thru my line first? thinking diesel is heavier than gas because of oil content....
View 2 Replies
Got to thinking today while my truck was warming up, why does the exhaust smell so bad. I think it is kinda interesting that the exhaust pipe is so clean also, like new matter of fact.
So what make the exhaust smell? The exhaust filter traps the partials right but where did the diesel smell go? I can understand it when in regen but in normal operation I don't get it. I guess I just don't the mechanics behind it. All I do know is that, what is left just stinks especially when warming up.
View 12 Replies
2006 overheats and starts blowing white smoke, smells like antifreeze, added 2 gals of water to make it 1 mile home. Smokes on the way @195 temp and when I shut it off it smokes out tailpipe for another 3 min. Smells like the head gaskets just went, what should I check? The eot and ect have been 10 deg or less.
This has 225,000 miles on it ran great before this, so would it be stupid too not get a redone set of heads while I'm doing the gaskets and studs?
I was thinking of getting heads from here, UCF Machine Shop - Precision machining, engine rebuilding and more. Cummins + Ford Rebuild Specialist. And a Sinister Diesel Complete Solution For Ford Powerstroke 2003-2007 6.0L. Are these the right places to deal with or should I look elsewhere?
View 14 Replies
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 Replies
My car was running rough, with white smoke and strong gas smell coming from exhaust. It died out on me a few times as if it was not getting enough acceleration. Well, I coded it and said misfire cylinder 3 and 4. I also tried to shut down 3 and 4, but did not shut down. I switched 3 and 4 with 1 and 2, still did not shut down cylinders 3 and 4. Engine coils are good, engine module was tested and passed twice. Ok, fuel injectors 3 and 4 were leaky and I changed them out. New spark plugs and boots. New oil and filter..(There was gas in my oil and oil in my air filter.) With the new parts....my car sounds soooo much better!!! still a little rough, does not bog down, but it still has the strong gas smell and white smoke from exhaust..(gas smell soo bad I had to open all doors to the garage!!) What else could be wrong?!?! I'm getting frustrated!! It also has NOT ever over heated, does not run high.
View 7 Replies
I have a 12 F150 with the 5.0L. it has 27000 miles on the clock. Noticed twice a small puff of white smoke coming out of the exhaust and decided to check the oil level and it was a quart low. The last oil change was done at 23000 miles and used Full Synthetic Pennzoil and a K&N filter. Called the local dealership I purchased at and they told me NOT to use full synthetic and should only be using Motorcraft semi synthetic with a Motorcraft filter. I know the dealerships will only endorse and advice Motorcraft products but what does everyone else use and think. In the meantime I added a quart of oil and all is fine.
View 5 Replies
