Ford 6.7L Power Stroke Diesel :: 2011 - Transmission Jerks Every Time When Shifts Down
Nov 6, 2015
Last week my 2011 KR Diesel with 85k on it stopped downshifting correctly. Basically when the transmission is cold (<150 degrees on the digital gauge for transmission fluid) it jerks everytime it shifts down from 4->3->2->1. Especially 3->2 and 2->1. I have never seen anything like this before. It's almost if you are getting reared ended when it shifts.
If I let it warm up it eventually goes away until it cools down again. I did take into the dealer and they said that a) there is definitely something wrong with the torque converter and b) I might actually need a new transmission which is anywhere between 4-7k depending on if its a reman or new.
This truck is barely broken in and I at this point have not towed a single thing with it. I had thought the transmission was covered up to 100k but it looks like it's only covered to 60 or 75k (I forgot which).
I've opened up a case with Ford but they kicked it back to the dealer. The dealer service manager has been really NICE and is definitely on my side that this SHOULD HAVE NEVER HAPPENED at this mileage. They also don't know how to fix it without pulling apart everything which is a lot of labor.
View 14 Replies
Advertisement
When the truck shifts into 5th gear i instantly feel a constant vibration and noise until it shifts to 6th gear. This happens nearly every time while driving at 40mph. Rpm range 1200 - 2000. I bought the truck new on June 30th and noticed the problem on my way to work on Monday July 2nd. Took it to the dealer on July 5th and the tech said it was the torque converter slipping. I drove it home because they didn't have time to work on it. Took it back on July 12th and the dealer has had it since (currently 30 days) They originally told me it was not the engine or transmission and it was an exhaust problem. Last week they said it was the motor mounts and said they would be done.
View 14 Replies
I currently have a 2006 F-250 6.0 with 187,XXX.
My problem that i am having is that the transmission recently within a couple weeks started acting weird about the same time 3 of my fuel injectors started failing. When i start up the truck and put it into drive it takes about 3-5 seconds to shift. Once it's in drive it runs pretty well but it will start shifting out of normal when i go to accelerate. Also when i go to slow down sometime the transmission shifts hard to a lower gear. I also have a video of the sound that it had started to make since its hard to describe.
Here are attached videos and photos. I want to hopefully fix the problems myself so i can learn more about my truck. I am going to handle the fuel injectors here soon since 2 are failing and ones about to these have been causing the truck to shudder at around 47-53 mph but after that its fine.
The transmission is stocked and never been altered, i do admit for 3-4 years I have changed the fluids or filters.
The truck is bullet proofed, sct tuner, upgraded turbo from stock, 4" exhaust, head studs and new everything when the engine was rebuilt and bulletproofed.
I plan on going to ford tmw to have them figure out the problem and hopefully its just solenoids so i can fix it myself. I have a link posted also where you can hear the noise it has been making when in R P and when shifting going down the road and it is a automatic.
YouTube.....
View 14 Replies
I have a 2006 F150 4x4. When the engine an transmission is cold it jerks/ Bogs when it shifts. After it warms up it doesn't jerk to bad sometimes but you can still notice it. Also when it shifts the RPM's drop low causing it to bog and jerk. RPM's will go from 1600 to about 800 when it shifts. It is and auto transmission. Today I wanted to try something so I pressed the button to turn the over drive off. Well it shift real good with the OD Off. Seem like with the OD Off it keeps the RPM's up a little higher so it doesn't bog and jerk. I put an Edge Programmer on it, but that didn't work. Still does the same thing with or without the programmer. I changed all my spark plug and coil packs. Truck goes great until it shifts.
View 1 Replies
In my 2011 F-250, 6.7, auto....it seems that at certain times went the tranny shifts from 2nd to 3rd and I pause with acceleration, for some reason the tranny seems to go into a slip mode and then slams into 3rd. Now I read about 8 months ago that there was a computer upgrade via Ford. Which they did when I was having some work done on the truck at the dealership.
View 14 Replies
Any input on replacing the entire transmission valve body or just individual shift solenoids? My truck has begun experiencing a harsh shift from 1st to 2nd under light acceleration accompanied by occasional shift flare from 2nd to 3rd and 5th to 6th. I have located parts to do either job. It looks straight forward from just disconnecting the harness. I also understand there are different bands associated with the solenoids. Is there a requirement to have new transmission programming to accompany swapping these components?
View 2 Replies
So I noticed that my transmission shifts (jerks) a little rougher than the 3 previous Lexi's that I had when shifting into drive or reverse when the car isnt fully warmed up. Is that "normal?" Had 2 ESes and 1 RX and while I do feel a slight lurch, the GS is a bit rough. I usually let the RPM drop to 1k before driving off on warm or cold days.
Separate incident: I recall at one point, I was going reverse, stopped, quickly shifted into drive and gave it some pedal (not full throttle) and felt a noticeable "bang" and violent lurch forward. Could that have hurt the transmission? Is the computer smart enough to prevent damage? I'm thinking this might have been the cause of it.
View 14 Replies
A while ago, I acquired a 1991 Mazda 626 automatic (currently 105,000 miles) that now has what appear to be the beginning of transmission issues. It hard shifts from 1st to 2nd - the shift jerks really hard when the car is cold but once I've driven it for 15-20 minutes the hard shift almost disappears completely and stays that way as long as the car is warm - except for stop and go traffic (Seattle traffic) than the hard shift comes back no matter how long I've been driving. The only other shifting issue I notice is on the hills where it seems to shift more frequently than I might expect it too.
Other than what I've described this car is in perfect condition inside and out, as well as engine-wise. My question is on transmissions and whether I should get a rebuilt one. I've taken it to multiple transmission shops and almost all have told me two things 1) I need a new transmission and 2) that the issue is a hard component problem and I could most likely drive this car for months or years without having to replace the transmission - if I want to put up with the rough shifts. They recommended just driving it until the transmission goes out and then replacing it.
View 6 Replies
Only during the summer, my 2003 Vue transmission jerks and shifts to (I believe) to a higher gear. Mechanic replaced the computer "harness" but it did not solve the problem. The car has little power to accelerate from a stop. I usually pull over, turn off the motor, and restart the vehicle.
View 3 Replies
Just bought a used 2011 ford f350 with the 6.7 diesel engine. Coming from a 7.3 1999 f350 with 330,000 miles, still going good. Took a 1000 mile trip on the 11 truck with out pulling anything did good. Hooked my enclosed trailer to it did a trip of 900 down and 900 back. Transmission temps were staying around the 250f, almost in yellow on gauge. Highest it went was 255f. Light never came on. Yesterday on trip without trailer was staying at 230f on trans temp. This is the first concern.
Second concern, had antifreeze coming out the cap on the degas bottle. Rolled over the hood and hit the drivers side windshield. Stopped un did the cap, it hissed. Put 2 quarts of antifreeze in drove on, this at 300 miles of trip. Primary water pump went out, half way there, at about 550 miles of trip. On trip back, about 1600 miles of trip, antifreeze was on windshield again. Undid cap, hissed, did not need to add any to it. Drove on no problems since. Have bought a new cap and installed.
Transmission doesn't want to shift right when its cold. First starting out. When it warms up shifts great. That's third problem.
View 14 Replies
Trans has new solenoids in the trans but is shifting too firm sometimes from 1-2 or 2-3.. It is tolerable going up, but when slowing down it jerks really bad from 2-1. Sounds and feels horrible for the trans and miserable during stop and go traffic. Ive had to switch it to Manual and start off in 2nd gear. Im deleted, with intake, and a custom sct x4 tune. My main question is there any way a new tune could have better shift points?
View 14 Replies
I have a 2004 F250 early build over 260K miles on it. After taking a trip out west Texas and back I noticed my truck starts to jerk a lot around the 50 to 60 mph range under moderate throttle. Getting a contribution code on #6. FICM voltage stays over 47v during KOEO and startup. Took an inferred thermometer and even after truck is at operating temp #6 is reading about 3 degrees cooler then the others.
When cranking the engine everything sounds smooth but startups are getting harder. Usually let it idle for a few minutes before taking off on cold start but I am having to let it warm up longer before I can get any power. Did a bubble test and passed and oil level hasnt changed. Fuel mileage has been sucking bad also. Safe to assume the injector is shot and needs replaced? Use Delo 5W-40 Syn every change with motorcraft filters.
View 4 Replies
1st to 2nd fine 2nd to 3rd it jumps a few times like it cant find the gear and you will see it on the video. I am confused what it could be. the truck received a new solenoid last year from ford because the tow haul light was flashing and now i have this issue. I believe it is also the reason the truck is running much slower down the 1/4.....
Video : F250 shifting problems - YouTube ....
View 2 Replies
My 6.0 is making a weird scuffing sound when I let off the gas and after it shifts. If I drive easy it doesn't seem to happen. But if I have to accelerate fast it will make the sound in between shifts and if I let off the gas real fast it will make the sound. It only lasts for about 3 seconds or so. It sounds like its possibly in the exhaust.
View 3 Replies
,the symptom that I'm wondering about is that when the truck is cruising at different high speeds like 65 or 75 it starts to jerk/jolt, if I accelerate it goes away, or if I let off the accelerator.
Once I settle on a different cruising speed it does it again. There is no smoke out the exhaust pipe, it does not loses any power, I look at the RPM's and they don't move when the jerking/jolting starts. Truck runs fine except for this issue.
I do get the P0404 and P0405 codes which are for the EGR valve and the sensor. By the way **is there an EGR SENSOR** anywhere on this engine, I seen some posts where people refer to it as the EBP Sensor, is this correct? I cleaned the EGR valve, but it did not do anything to fix the issue. I'm thinking I damaged the valve when I cleaned it, but I would like to verify that this symptom could be the EGR valve before I buy a new one.
View 6 Replies
I just got a 2006 ford F250 lariat fx4,and it's already at the shop.. when cold start it has some white smoke, but once I get up to highway speeds the truck jerks and bucks. turbo is putting out normal boost. I've changed oil and filters along with fuel filters. also put on a new serpentine belt and pulley, air filter and have everything cleaned real good. the truck is acting like it's starving for fuel. FICM or injectors ?
View 14 Replies
Ok so here is my problem now. I'm sure its in the tramny but not sure what else. My shift from 3-5 has always been a little hard. Yesterday on my way to work I noticed shifts 1 thru 3 were hitting hard. Once I got up to 65 mph it was okay. Then pulling into work when I shifted to reverse it didn't go into gear right away and then it would hit into gear. Later that evening on my way home from work it was shifting the same but seemed worse. Then my tow/haul light started flashing and it seemed like the torque convertor wouldn't lock in. It would just stay in 5th gear and the more throttle I gave it the rpms would go up but I would only get a little response from it. Then a few miles down the road it just completely shut off on me. It will not even try to turn over. I could also hear a noise coming from underneath the truck. Something ive never heard before. I really need to figure this out
View 14 Replies
Having transmission problems? Everything I've read before says these transmissions are better than gm Allison's and they can handle up to 600 horse before you gotta worry about beefing them up but mines starting to act funny.
How important is the transmission tune? My truck it's tuned with the spe hot tune and trans tune. Didn't like the way it clunk bang hard shifts though so I ran factory trans tune for a while but it felt very soft like it was slipping when I got after it on the performance setting of spe hot so I went back to spe trans file.
I get a little twang sound that sounds like it's coming from the trans between 3-4 gear shifts, initially only heard it after getting on it hard in performance but it's getting worse and happens on stock power level under light acceleration now sometimes. Also I lost all gears briefly and it wouldn't shift into manual at all when I stopped to turn around the other day.
Working fine in drive but when I shifted out to reverse it had nothing in any gear and manual wouldn't light up on the display. I shut it off and restarted the engine and it came back and worked fine after that but not sure what happened there, don't think it's good though. Did using the stock transmission file with the hot engine tune or the hard clunk bang custom trans file up my trans, freak malfunction?
View 14 Replies
My friend has a 2006 F-450 and he said the Tow/Haul light blinks and the shifts are real slow. He has stopped towing now and it still drives.
I have read everything from toasted tranny to chaffed wire harness across tranny crossmember to the TFT sensor. My guess is the TFT sensor given his symptoms. If I am right the sensor is just to the rear of where the dipstick comes thru the tranny case. 1/4 turn and pull it out. Kinda like a bulb I guess.
Another question, is it necessary to replace the harness while in there as well? Is the Connection listed below the harness I am asking about? I found these parts on a thread from here:
Sensor (1): 3C3Z-7H141-AA;
Connection (1) 4C3Z-7G276-AA;
Gasket (1): 3C3Z-7C155-DA;
Fluid (10): XT-6-QSP
View 9 Replies
I have a 2003 Mazda 6. Almost every day, after starting it and driving maybe .10 of a mile, it seems as my car shifts, it shifts really hard, like a thump. I am thinking of having the Transmission serviced. Is this worth it? About what should the cost be? What do they do, just drain the fluid and add new?
View 2 Replies
Purchased 2011 3 weeks ago. Due to not paying attention, put gas in diesel. Had tank dropped and drained but after reassembly, fuel gauge inop. When turn ignition switch on, get normal sweep of all dash gauges but fuel gauge does not read. 2nd tech says sender okay, must be gauge. Dealer ssays if it sweeps, it isn't the gauge. 011 F250 6.7L.....
View 7 Replies
