Ford 6.7L Power Stroke Diesel :: 2011 - Rough Idle - Surging And Loss Of Power?
Oct 17, 2015
I was driving my 2011 the other day home from work and experienced a rough idle. Normally the truck idles pretty smooth. I noticed when I was driving at highway speeds the truck seems to shake a lot. I pulled over and turned the truck off. I did a walk around and could find anything out of the ordinary. I started it back up and no more rough idle. However while i was driving at freeway speeds I could feel a momentary lack of power, then the truck would regain its speed. This would only last a sec or two.
I figured I'd give it a few days.... well now its gotten worse. Its doing the same thing but a noticeable difference in the lack of power. I still have boost pressure and the turbo seems to working fine. Im trying to figure out what it might be. I'll be taking my truck into ford again...
View 12 Replies
Advertisement
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 Replies
Dad has a 01 one ton with the 7.3 and isn't real tech savvy so I'm posting for him. He is the original owner and has been complaining recently about the lack of power. Particularly the upper end. He is having to downshift way more often and where he used to not have to. And we've both noticed a very noticeable shake at idle. Not a vibration but a true shake. He changes the oil every 5000 on the dot and I've gone and changed the air and fuel filter and ran hose and see foam and royal purple injector cleaner through it with no results. Truck is all stock with 225000 on it.
View 7 Replies
I have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.
The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.
He said he is going to come by tomorrow with the box to check each individual cylinder.
View 14 Replies
I have an early 99 F-350 with 268K miles. It is bone stock right down to the factory exhaust. A couple months ago I started have a rough idle and surging while driving problem. I never got a check engine light but I borrowed a scan tool from a friend and pulled the following codes: P1690 (wastegate solenoid), P0381 (glow plug circuit malfunction), P0269 Cylinder 3 Contribution/Balance Fault, and P0284 Cylinder 8 Contribution/Balance Fault.
I did some research and everything I read said it was most likely the CPS. So I changed the CPS. The truck ran fine for for a few days but then it started acting up again occasionally. I noticed that most of the time when it acted up was at start up when the engine was cold and I also figured out that if I shut the truck off and re-started it (sometimes I had to do it 2 or 3 times) it would clear up and run normal.
A buddy of mine that has a 2000 F-250 said he had a similar problem with his truck and it ended up being the ICP sensor. We switched his ICP with mine and I changed my oil at the same time (because it was due for an oil change). My truck ran flawless for over 2-weeks (over 200 miles) so I put a new ICP in my truck. Note: my buddy did not experience any problems with his truck with my ICP in it.
I've put about 700 miles on the new IPR and the truck has started to act up again. Once again shutting the truck off & re-starting it will clear it up and still no check engine light. I took it to a local "diesel specialty shop" while it was running rough and they hooked it to their scanner and got P1280 (Inj. Control Pressure Low), P1690 (Wastegate Solenoid Fault), P0381 (Glow Plug Indicator), P0269 Cylinder 3 Contribution / Balance Fault, and P0284 Cylinder 8 Contribution / Balance Fault.
They never did anything other than hook it to a machine & check the codes but their diagnosis is my High Pressure Oil Pump is going bad and my #3 and #8 injectors are going bad. They recommended I let them replace all 8 injectors and the High Pressure Oil Pump. The problem I have is they can't give me a REASONABLE explanation as to why re-starting the truck a few times clears up the problem.
View 14 Replies
My uncle was pulling his fiver to the beach yesterday with his 2011 f-350 6.7. He lost power, the truck got very loud, and there is a very strong stale kerosene smell in the cab. Strong enough to require the windows be down for ventilation. He was able to limp on into the campground and has an appointment with the dealership Monday. The truck has 19,000 miles and is still covered under the extended warranty.
View 8 Replies
Truck = 2011 F250 150,000 miles, no modifications, stock.
Truck lost power yesterday, no boost, and no codes. When driving on Friday, I started moving from a red light. The truck seemed very sluggish. Then I noticed it downshift going up a small hill that it never downshifts before. I looked, and noticed the turbo gauge at 0, no boost. I pulled over, turned it off, then restarted it, but still no boost, and the truck is very under-powered. I looked over the area, and do not notice any leaks, also no leaks underneath. I hooked up my OBD reader, and no codes., the boost gauge is on zero, and the truck has lost significant power. I no longer hear the turbo spooling.
I have spent the past several hours searching sites and forums (Started with FTE ), and it seems that most believe a restart of the truck has solved it for them. However, this is not the case for me, a restart, even after letting it sit overnight did not resolve the issue.
I did see one reference that replacing a NOX sensor solved their problem. This brings up some interesting truck history. Back in June 2017, my truck threw the following codes, P207F and P20EE.
P207F - Reductant Quality Performance
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
The message said I have 200 miles until reduced power. Since it was a Friday, not much I could do at the time so I let it sit overnight, and then the next morning the message was gone. I plugged in the OBD reader and cleared the only remaining code (P20EE), and its been a very happy truck until yesterday.
So my question, can a bad NOX sensor cause the issue of loss of turbo boost, with no codes? Is there another possible cause?
View 3 Replies
Getting DTC P0401 on my 2011 with 92K miles. First time I got the CEL, we were on vacation, so I read the code, took a screen shot, then cleared it. Called my normal dealer, setup an appt, verified that they thought the truck was safe to drive. Coming home from vacation, I was pulling the TT in my sig, and noticed significant loss of power on hills that I have pulled many times before that I couldnt even hold 55 on now. Transmission dropped into 4th a couple times, on hills that it would sometimes stay in 6th, or at most drop to 5th.
CEL stayed off for a week , and came back on again. The funny thing is that after a day or 2, the CEL went back out on its own. I read the codes the P0401 is still there as a stored code(I did not clear this time). Around town the truck drives fine, the only thing I noticed was the decrease in power when towing. Truck is at the dealer now. TECH "isn't convinced" yet that there is a problem. He is not finished diagnosing yet, and I am sure that he has specific tests to run, but I am starting to fear that I will be getting the call to come get my truck.
View 6 Replies
My 2011 6.7 suddenly lost power, started making noise and then stalled out.
After finding out that there are zero 24 hour service companies available in the LA area, I was able to get it towed to the local Ford dealer.the next day they told me it had dropped the #5 cylinder and that they would have to tear into it to find out what happened.
While I realize that any thoughts on the situation would be primarily idle speculation, what would cause this to happen at only 125,000 miles.
View 14 Replies
I replaced the exhaust back pressure sensor and the readings on my sct programmer didn't change at all so I don't want to keep blindly throwing money at it if one of you has experienced this and found a cure. The interesting thing is it never throws a code or check engine light or anything according to my sct. Doesn't even show that the egr valve is unplugged. I have read that it could be a bad turbo, vgt solenoid, icp, throttle positioning sensor, or a couple other things.
It feels like I'm the front car in a bump draft in cup racing when I'm at a steady speed. The truck has arp head studs, new style egr cooler with the tubes, coolant filtration, new oil cooler, new ficm, blue spring, all filters have been changed in the last month.
2004 powerstroke surge/ rapid idle - YouTube ...
View 14 Replies
Just bought a 2006 F250 with 6.0. A week or so ago, it surged once at idle at a light. Sort of felt like someone bumped into your rear. It has gotten more frequent over the last week or so. Now it does it often. It tends to rev up and then back down again over and over. Then it will clear up again. My brother said his 7.3 used to have a similar problem (as did quite a few others apprently) and it was the Cam positioning sensor (CPS). Where is it located?
View 14 Replies
A few weeks ago i had a surging idle issue very intermittently, and it went away for a while so i stopped thinking about it. Just got back from a weekend in vermont, about 130 miles each way, and i noticed as soon as i got to vermont and came to a stop sign it was surging, and when i just got home it was surging again. Why would this have picked back up after long stretches of running for a while? Runs great as far as i know, just have this surging idle for some reason.
View 14 Replies
So any ICP sensor been proven bad but i was not leaking oil? The symptoms of my truck sound similar to a bad ICP...fluctuating idle, surging, stalling, but it does run and start. IT tends to start acting up when it hits operating temp.
I have an 04 and the ICP sensor is in the easy spot to get to on the valve cover vs under the turbo (that's awesome) so its an easy swap. but just wondering if there is any way to test it over simply swapping it. I do not have a monitor yet but a dongle is on order and will get the torque app for my tablet.
View 14 Replies
2011 F350 diesel with 10,000 miles. I have been experiencing problems with the truck loosing power, making rough running noise (pinging like an older diesel), and vibrating. As though the motor is bogging down. It usually occurs on small inclines or hills with the truck in higher gears and low rpms. It will also occur running on flat ground 65-70 mph. Had it occur once while turning the truck around in 1st gear and low rpms. Depressing the accelerator will bring the truck out of it.
This problem occurs randomly sometimes a couple of times a week to not at all. Took to dealer and they found no codes and of couse it didn't do it on the hour long test drive I took the mechanic on. However they did say they had two other owners come in with the same complaints, but could not get trucks to repeat the issue. Problem usually occurs in the hotter part of the day, maybe just coincidence. I had seen similar posts with this problem but no conclusions.
View 14 Replies
Have a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 Replies
I recently bought a 2004 6.0 extended cab truck. It has 223,000 miles on it and has been running great. Bought it here in Arkansas where I live and recently drove it to Texas and back after having just put some Hot Shot oil treatment cleaner in it. I ran it the 1000 miles as it suggests. Just the other day as it was hitting the 1000 mile mark the truck started to lunge/runaway and stalled. I finally got it back home and started looking into the issue. Based on what it was doing, (lunging/running away, and at idle in park random burst of rpms and then dying after doing it a few times), I started to do some research. Most of the answers I found claimed it was the IPR valve. I found that the IPR valve is supposed to, as claimed by some, be pulled and inspected every 100,000 miles are so and if need be replaced or the rebuild kit gotten for it. So I decided to just replace it as well as the oil, oil filter and fuel filters.
When replacing the IPR valve I noticed that it was original and that its screen was missing. I didn't have any problem moving the little piston in the center of the shaft with a small bolt however that doesn't really mean that it isn't bad. I tried a magnet to see if the screen was still in there and nothing came out. I did not try using a camera as I do not currently have one, to look inside the port to see if I saw it. After replacing the IPR valve with a brand new one and changing the oil I started the truck. It seemed to be running a little ruff so I let it warm up. Not one minute later the exact same thing started happening, lunging/running away (random increase and decrease in rpms), so I called it a night. The next morning I decided to change the fuel filters. No that it matters the order in which I did it, but I changed the top end filter first and the the one on the frame with the dealer recommended OEM filters as was the case with the oil. I did find in the filter on the frame that there was a small amount of sand and clay soil looking matter in the filter. I did clean out the filter housing as well.
After replacing the filters I started the truck to warm it up. I noticed that it was still running a little ruff but no random, lunging/running away (random increase and decrease in rpms). However after five minutes it started coming back. I finished letting the truck warm up and took it for a drive. Got it up to between 7-80mph for about 15 miles to try and see if I could "blow out" whatever may be in the fuel if that was even an issue I do not know. The truck seemed to get more power and run a little more smoothly so I stopped at my buddies house not to far from where I was and let it idle. No issues other than a little ruff idle. After about 10min I took off towards home doing similar speeds. I noticed at a little over 2000rpms that the truck was shaking a little but so I dropped the speed down. When I got home not more than one min after idling the same issue, lunging/running away (random increase and decrease in rpms), started happening again.
At this point I took back to the interwebs and came across a post that said the ICP might be bad and does cause this issue, lunging/running away (random increase and decrease in rpms). However I also noticed that this is a huge debate as to whether or not the ICP can cause this. Ford master mechanics say no and other mechanics say yes and round and round it goes. I decided to do the simple test many recommended which was to simply unplug the ICP and see if anything changes. Things did change. No more lunging/running away (random increase and decrease in rpms). Not more than two minutes after plugging it back in, allowing the computer to account for it now, the lunging/running away (random increase and decrease in rpms) came back. In the middle of it doing this I unplugged it and that went away. So needless to say I replaced the ICP and voila the lunging/running away (random increase and decrease in rpms) is gone but the ruff idle is still there along with a slight loss of power.
To answer some questions:
1. The oil and water are not mixing so I am almost positive that the heads are fine
2. The intercooler couplings are leaking a bit. I have ordered the new ones and will replace them as soon as they come in. Can this cause the issue?
3. I am blowing no white or black smoke except for when the lunging/running away (random increase and decrease in rpms) issue was present and the truck almost died. It would knock occasionally when it almost died and would send a slight puff of black smoke which I assume is a low or high fuel issue from the truck trying to die
4. I have not had the no start issue at all
5. I did not see any debris in the oil during the oil change
6. I didn't do the air test on the ICP port as I do not have the adapter.
7. The only code I got on the IBD II port was when I unplugged the ICP which was to be expected
8. I found no damaged wires
I am at the point where I am wanting to take it to ford to have them run a diagnostic on it but am wondering if there is anything else I need to be looking for. Here are a few questions I have.
1. Does this sound like a bad injector? (When I bought the truck it would sound like a misfire or ruff idle condition was present for about 5-15 seconds and then it would smooth out with no issues. It would run a little ruff if you tried to take off without letting it warm up, which I did once or twice and low rpms, but when it warmed up no issues were present).
2. Could this be the HPOP?
3. Could this be the FCIM? (The previous owner had replaced the FCIM not to long ago with one from Ford I believe. Said it cost him something like $700)
4. Could this be something clogging the oil screen under the manifold?
My final question right now is do any of you know where or what brand OBD II reader or software I can get for a decent price that will tell me the voltage of each injector and FCIM is without me having to go to Ford to get it looked at.
View 14 Replies
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 Replies
05 6.0 deleted and studded. 170k fresh filters and oil, no CEL or codes.
This has happened 3x in months, so it intermittent. Truck will start fine cold, except for this last episode ....
Truck starts right up, idles correctly, speed bumps up if its cold enough to trigger the high idle. About mid way through its warm up, at approx 130-140 idle falls off, barely runs. Almost knocking. Black smoke if you give it throttle. Has no power when its doing this. Truck will not move and almost dies in gear. Give it til 185ish degrees then pooof! All good.
However 2 days ago it wouldn't start. Cranks but won't catch. Stumbles and dies. Finally got it to start after setting the charger on it. I killed it. But this time when it started it was straight into its rough idle, no power...until about 180. I switched it off, restarted it and it was totally fine
Ficm is 47-47.5. Every now and then I see a 46.5 for a split sec
Hpop is 700-800cold cranking.
Not sure what else to look at.
Moto craft filters.
Amsoil 5w-40
Archoil in the fuel and oil
Twc3 at every fill up.
View 5 Replies
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 Replies
This morning I noticed when I started the truck had a rough idle shaking truck. The truck felt weak. Boost would go up but truck felt like it was in sand. While coasting on the highway at 50-55mph the truck not only lags in power but vibrates viciously until the overdrive kicks in that vibrations in cab and ssteering wheel go away.. What might be going on?
View 6 Replies
I have 2007 6.0, rough idle starts, rough and no power till engine reaches running temperature, runs great after that. If the engine is off for half hour, and restarted, runs rough again till engine temp is back again.
View 3 Replies
