Ford 6.7L Power Stroke Diesel :: 2011 F250 Stall During Truck Pull?
Aug 11, 2015
I have a 2011 F250 6.7 4x4 CCLB. About 90k on the odometer.
Full flopro exhaust(no cat, no dpf) and a H&S tow tune. Otherwise stock.
8" lift and 37" toyo mt tires.
Anyways, I ran the truck in my first truck pull ever a few weeks ago. I pulled in 4wd high, rear locked, tow/haul mode, traction control off 2nd gear.
I wasn't able to pay super close attention to all of the stock gauges, but it didn't over heat and it didn't rev over 3000rpm. It was pulling like a freight train until the 125' mark and it just shut off. I thought something may have broken.... I put it in neutral, cycled the key and it started right back up....
Checked for anything obviously wrong, no fluids, all boots looked attached and fine. Nothing. Drive it home and haven't had a problem since. No CEL, no warning no anything. So why the truck may have stalled on me?
View 14 Replies
Advertisement
I have a 2006 that shuts off in a hard pull, if I wait 3 minutes it starts again. I hooked up my scan tool and when it dies and I crank it it only builds 200psi oil pressure, let it sit it builds enough pressure to run fine. If I dont push it over 3500psi for more than minute it wont die pull a hill it dies again. Is it the hpop or an o-ring.
View 10 Replies
New here but long time lurker. I have a 2006 e350 with 6.0, bought it from a friend not long ago. The work that has been done to it the last 50,000 miles is as follows.. New hpop, all new injectors, egr delete, sct tuner, stand pipes and dummy plugs. I had it for a week and would get a no start hot once in a while. This issue had become worse and the truck started to stall as the RPMs dropped. Reading here i replaced crank sensor and the stalling stopped but the no start hot continued. I took it to a local diesel repair shop and they did the following..
Use a test ipr (no change), replaced ipr pigtail (was cracked) air test (leak under pass valve cover) replaced stand pipes and dummy plugs on this side. They said no leaks and I was good. Truck worked as its supposed to for 1 day and the no start hot issue reared its head again. Took it back and now they say the hpop is bad. The pump that was put in about 50,000 miles ago was a bostech? do these go out? Sangauge reads good ficm, but seams ipr doesn't climb that quick.
View 14 Replies
While driving the other day, the truck suddenly began to stall when pressing the accelerator. The water in fuel light came on as did the glow plug light. This continued with the truck sometimes dying all the way and other times just stalling then picking back up. No difference in throttle pressure seemed to make a difference except that letting off totally then slowly pressing seemed to let it keep running sometimes.
So I get home and drain the fuel water separator. I gets about a thimble full of water and lots of the rusty looking junk others have talked about. Try to run the truck again, same thing as before. I then changed fuel filters and thought that had it licked but after about 10 minutes it started again. By the way, the 6mm plug seemed to have about a third of the threads rusted off. Not sure what that means as I drain it at least twice a year.
I have read a lot about the ICP and IPR issues and was wondering if this could be my problem. I am hoping its not the HPOP. My other thought was something in the fuel tank blocking the in tank filter. I checked the top mount bowl and it was only about two thirds full after running the truck
Truck info: Late 2004 Ford F350 Dually 4x4 crewcab, 6.0, EGR delete plate,4" turbo back exhaust with cat delete, no muffler,K&N filter and filter box, Diablo tuner usually set to 60hp upgrade.
View 14 Replies
I have had literally no issues with my 2004 F250 Super Duty. Went out and started the truck like every other time for the past 13 years. Started backing out of the driveway and burped the throttle and it just quit??
I put back into park and it rolled over for about a minute and finally caught. When i put it back into gear i had zero throttle response. I have a NOx sensor fault code and and EGR fault code. I replaced the FICM 2 years ago.
View 3 Replies
Purchased 2011 3 weeks ago. Due to not paying attention, put gas in diesel. Had tank dropped and drained but after reassembly, fuel gauge inop. When turn ignition switch on, get normal sweep of all dash gauges but fuel gauge does not read. 2nd tech says sender okay, must be gauge. Dealer ssays if it sweeps, it isn't the gauge. 011 F250 6.7L.....
View 7 Replies
My 05 F250 CC 4x4 had a problem where it was wondering to the right.
I had the front end checked out and they said everything was good and within spec but they discovered a bad tire (internal belt separation).
Had two new front tires installed/balanced and the problem seemed to go away for a few months.
Now the problem is back even with the new tires. Could the steering box cause this or is there something else I should be looking at?
View 2 Replies
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 Replies
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 Replies
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 Replies
I have a 2006 F250 6.0L. Just had a used motor with 108k miles put in. Had the motor studded, fire ringed, new injectors, new glow plugs, new radiator fluid filter system installed, had egr delete done, ficm board replaced, fuel pump replaced, a few other small items replaced as well. The problem I'm having is the truck runs like it has a miss until it warms up.
After that, it runs fine. It takes about 10/15 miles of driving before it runs like it should. Letting it run in the driveway for 10/15 minutes to warm up doesn't make a difference. When the truck starts, it lopes at an idle for about 5 mins before turbo kicks in & starts whistling. When I start driving it shakes & feels like it has no power until it warms up. Then you'd never know anything was wrong. Put way too much $ into the truck so far and can't keep going.
View 7 Replies
I have a 2004 F250 with a 6.0l Diesel and a 5 speed automatic. The truck is 4 wheel drive. As far as I know it is completely stock and has 236,500 miles on it. I thought that I was having stiction issues because when the truck is cold and when driving ~55 mph (1500 rpm) in 6th, the truck shudders until ECT gets to about 150F. This is at a constant speed, when accelerating or decelerating it doesn't shudder. Today I held 40 mph (1500 rpm) in 5th and there was no shudder. I don't know the TFT the shudder goes away at because the epiphany about the transmission was today. Once warmed up there is no to very slight shudder and only around 55 mph (1500 rpm). Above or below that the shudder goes away.
View 11 Replies
I'm posting this for my neighbor who has a F250 that's 8 years old. He has replaced many parts, engine from what I know but now when he starts the truck it starts fine but as soon as he starts the truck, the brakes lock up. He can't move it. He hasn't had the chance to move it because the brakes lock as soon as the truck starts. It starts fine and idles fine but can't move because the brakes are locked. Tomorrow the tow truck will haul it to the ford dealership so they can look at it and run the diagnosis computer on it.
View 4 Replies
2011 F250 6.7 Lariot Fx4. My factory Trailor mirrors won't extend. When I push the button it just gives me two chimes. The power fold and other options work, just not the extend. Not sure but don't think it's a fuse since everything else works.
View 9 Replies
I have an 03 6.0 F250. My truck started blowing fuse #45 and it would kill my gauges (fuel, oil, mph, rpm, temp, trans temp, and odometer) and I was just replacing the fuse and putting off the repair.
However, the most recent time my gauges blew, the fuse did not, and I put in a 20 amp fuse, in hopes that it would not blow so quickly, bad idea. So naturally, I ordered a new shift lever, in hopes that it would fix the gauges and I wouldn't have to deal with it anymore, but I think it was too late and something else needs to be replaced. What I could possibly have blown by having a larger fuse in there?
View 9 Replies
I have a 2011 Ford F250 6.7 Powerstroke. It has 107,000 miles on it.
The other day I was driving it down the highway and it got a Reduced Engine Power message on the dash. It lost power and I got off the highway to the service road. Then it died on me.
Had to get it pushed to a station then towed home. It wouldn't start. The starter cranks over for a few seconds but engine won't start. Checked all the fluid levels and batteries. My DEF fluid was only a half gallon low.
What I have noticed is that the DEF level indicator hasn't reminded me that it was low for over 4-5 months now. I had been putting in about 2-3 gallons every 3 months or so. But it hasn't reminded me lately and I just forgot. This is my first diesel.
View 5 Replies
My 2011 6.7L F250 Superduty died on interstate the other night. Picking up throttle pulling onto interstate when a message came on the dash "reducing engine power" and the truck died. It will crank but will not start. It will start on ether but dies when that runs out. Has the following codes... p1249 Wastegate control valve, p0087 fuel rail/system pressure too low, p1291 & p1292 injector high side short to ground or battery (bank 1 & 2), p2291 injector control pressure too low-engine cranking. The codes are telling me I don't have enough fuel pressure but scan tool says I have 4000 w/ key on and 6370 while cranking and I thought 5000 was the pressure needed.
View 9 Replies
2011 F-250 6.7
H&S Mini Maxx
Fully Deleted
What is going on with my tranny. I purchased my truck back in August with only 14k miles on it. It was a weekend camper hauler for the previous owner who drove very little. He bought it brand new and had it fully deleted with the mini maxx put in right away. I bought it in that current condition. Since buying it I have used it as a daily driver. Current mileage is 21k.
About 2 weeks ago I did 2 things. First, I decided to update my mini maxx from H&S's website to make it current as I was having a really firm shift from 2-3 gear. This is a know issue with my year truck due to a solenoid issue and I figured a more up to date tune might work. Second thing I did was tow for the first time since getting it. I towed an open bed car hauler with an SUV on it down the highway for about 150 miles. Prob about 7k#s. While on this trip I noticed my tranny temp go up to 235 degrees. When I reached my destination I parked the truck and stayed the night and returned back down the highway unloaded not towing anything and it still went back to 235. Trip was on the highway and is mostly flat with very few hills.
I monitor all gauges religiously and know my trans has never even gotten close to 200 before. My oil and coolant were both running in their normal mid to high 190 range and everything else appeared normal about the truck. I have talked to several diesel performance shops and received multiple ideas about what it might be. All seem to be in agreement that it is not my tuner as no one else that I can find has had this issue with their mini maxx after updating.
What is wrong range from the solenoid issue making the gears slip causing additional heat.... to my thermostat in the coolant valve having gone bad. I have had it in the local Ford dealership all week and they are completely clueless. They claim that everything they can check with their computer for flow and whatnot is functioning perfectly fine. They also claim that at 235 it is not out of spec according to Ford and that Ford doesn't consider this temperature to even be an issue or something that needs to be fixed.
View 14 Replies
I'm starting to get an intermittent CEL for P2074 ("Manifold Absolute Pressure/Mass Air Flow - Throttle Position Correlation at Higher Load"). It first came on Saturday halfway into a 4 hour drive (Not towing, just driving 75mph-80mph on the freeway). I cleared the code and restarted the truck and it immediately came back on. About a half hour later I stopped for fuel, cleared the code, and it stayed off for the rest of the trip.
Got into the truck today and drove it for 10 minutes (driving around town) and it came back on. Cleared the code and restarted the truck, drove it for about a hour and it never came back on. The truck is running and driving just fine.
The truck is a 2011 F-250, all stock (except for a AFE Cold air intake that's been on the truck for a while now). The truck has about 98,000 miles.
From what I've read on other posts, it might just be a mass air flow sensor? Should I just replace that myself, or pay the $100 extended warranty deductible and take it into Ford?
View 7 Replies
We got "bad" gas in Feb, 2016, had to replace entire fuel system. Haven't driven the truck but 4000 miles. Last week, she started spitting and sputtering and lost power. We could see fuel pouring out. NO CEL. Towed (AAA has paid for itself several times over with this truck) to dealer that replaced the fuel system, still waiting to hear from them. Does this sound like it should be under the warranty for the work they did? We have averaged a huge repair bill about every 3-4 months on this truck, 2011 F250 Lariat, 8cyl, 6.7L, since we bought it 2 years ago.
View 1 Replies
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
View 6 Replies
