Ford 6.7L Power Stroke Diesel :: 2006 - How Long Do Batteries Hold Up
Jul 5, 2017
About how long do batteries hold up in this truck? I ask because in my 06 6.0 it was an annual event 2 batteries and an alternator.
View 14 Replies
Jul 5, 2017
Advertisement
Ford 6.0L Power Stroke Diesel :: 2006 - Replacing Batteries Repeatedly - Parasitic Draw?
I have a 2006 F250. Past two winters my batteries have died. Last yr., bought 2 new batteries and a new alternator. This winter, battries have been replaced twice. I only drive the truck maybe once a week, about 5 miles total. I live in Indiana and we have had many sub zero temps this yr. Its been in the shop all week, the mechanic states that they are finding an extremely small draw but cannot find where it is coming from. The mechanic is wondering if I am driving it enough. Any thoughts on this? Also my batteries came from auto zone, the mechanics thought it was bad that I had bought them from auto zone.....not sure if that should even be a factor....
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - Long Crank Time
I have a 2006 F350. I have long crank times. No Codes. I have Autoenginuity with Enhanced Codes and everything shows fine. I replaces standpipe and dummy plugs. Glow Plugs and harness. I was hoping it not be the STC but I needed to do oil cooler so wanted to eliminate STC. Got truck apart and the STC Fitting is newer style so I'm kinda bummed out. Not sure if I'm missing something and as far as I have it torn down is there anyway to test what could be causing the problem? Or just put it back together and keep my fingers crossed that whoever put the new STC fitting in screwed it up. I'm beginning to not like my truck.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Lack Of Power / Truck Will Barely Move And Takes Long Time To Accelerate Under A Load
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
Ford 6.0L Power Stroke Diesel :: 2006 - Rough Idle / Dies Warm And Long Crank
My 06 currently has 296k miles. 3 years ago I put a lot into her. Dummy plugs, stand pipes, STC, hg,studs, oil cooler, bpd egr cooler. Cleaned spool valves and fresh o rings in injectors. (Alliant) plus a lot more that I can't remember. Ran very very well after all that.
Fast forward to a few weeks ago. Driving down road and truck died as I let off pedal to slow down for turn onto my road. Took about 7-8 tries to get started back up. Icp was reading in the 300's until it finally started. Made it home. Shut it off. And started right back up.
Few days later truck died again same way. Let off to make a turn. Several attempts to restart icp was in the 300's again. Once it started building 420ish it sounded like it was firing a few injectors and slowly started running. The next time it happened the same way but when I got it back running I eased to my inlaws like less than a mile. When I got to their house and pulled in and went to back up to turn around the display on dash said low oil pressure and started missing a little. So once I got home started researching.
A few days ago I pulled out the low pressure oil regulator to check it out. It was clean but did have some mild scaring. I used some fine scotch rite and smooth it out a a little. It moved freely in the bore so I put it back together. Then pulled the oil filter cap off to check the little black valve. I noticed the filter was not dripping with oil like normally when I change the oil. And yes it's motor craft filter and cap. It checked out ok. Press it down and turned engine over and it filled and held. Let off of it and it drained.
Next I air checked the high pressure side. Applied air and waited until I could hear the air (IPR still open) then closed the IPR. Couldn't hear any leaks. Just a very very minor his and couldn't pin point where. So I went ahead and went to dealer and got new stand pipes and plugs. And ordered new print set for injectors. Pulled injectors and didn't see any smoking guns. Replaced prongs, stand pipe and dummy plugs and put it all back together. Cleaned the injector cups and hold down bolt holes. Torqued injectors to spec.
Got it all done and rotate motor by wire next to heater blower to assist prime system. Tried to start it up and it took two tries but fired right up and sounded smooth as hell. After it idled a few minutes I saw a haze from exhaust. It smelt just like fuel. A few minutes later started idle a little rough. Gave it some go pedel and it was rougher at about 1600-1800rpms and couldn't feel it above 2k. Got my laptop out with AE and done balance test. Did not show anything. No codes either.
Ford 6.0L Power Stroke Diesel :: Batteries Going Dead Overnight
My batteries go dead over night, had them checked but they say there good, can't figure out what's causing them to die.
View 8 RepliesFord 6.7L Power Stroke Diesel :: 2014 F350 Won't Start / Batteries Going Bad?
My 2014 350 DRW has a battery problem......If it sets for a couple hours, it won't start. With a jump from a very small battery box, it starts right up. I charged it last week for 4 hours and still when in OKC it would need to be jumped at each restart. Do I have one of the batteries going bad.....
View 6 RepliesFord 6.7L Power Stroke Diesel :: Batteries Died Again With 2500 Miles?
I didn't drive my truck for one day and the batteries are died. This is the second time this has happen. That is a pretty fast drain time. THe truck only has 2500 miles on it. And I;m talking the batteries a dead dead. I hate having to take the truck to the shop. Just a big inconvenience. And it only happens about three weeks apart. I bet that would be pretty had to find the problem.
View 5 RepliesFord 6.7L Power Stroke Diesel :: Jump Starting With Dual Batteries
If I'm giving a jump:
Assume I hook positive and negative cables to the respective terminals of one of the two batteries. The alternative would be hooking positive cable to one battery and negative cable to the other battery, or does that make 24 volts? I'm also assuming if it is just the one battery, it does not matter which one you jump from?
If I'm receiving a jump:
I assume positive cable to positive post of one battery and negative cable to a good ground under the hood somewhere? Again, does it matter which battery I use? I wonder where a good ground is on this crowded diesel engine and aluminum body. Front radiator supports?
Ford 6.0L Power Stroke Diesel :: No Start - Replaced Starter And 2 New Batteries?
In the last 2 months I've replaced my starter and 2 new batteries. I've tested the alternator and it's fine. What more is there? I'm guessing the FICM is going to crap. If I attach a scangauge 2 to it now would it tell me if that's the problem?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Inverter Connections On Dual Batteries
I have a 2000 watt inverter and I want to connect it to my 2011 F250 Super Duty. Which battery do I connect it too. This will only be used every once in awhile.
View 12 RepliesFord 6.0L Power Stroke Diesel :: Way To Check Batteries Health With OBD2 Gauge?
Is there a way to check to see battery health with Dashboss? I know I can check charging system, but is there a way to monitor if the batteries themselves are going south on me?
View 5 RepliesFord 6.0L Power Stroke Diesel :: Charging Line In 7 Pin Connector For Trailer Batteries
I have both a hydraulic dump trailer with two 12v batteries and an RV trailer with two 6v batteries to supply 12v. Both trailer's batteries are wired to be charged from the tow vehicle if the TV is equipped with a charge line.
Does the OEM 7 pin connector on a 2005 Ford 6.0 F250 CC 4X4 have a charging line on it? If so which terminal / pin is it?
What gauge of wire is it and how much amperage will it deliver to the connector? For testing, when is it hot? When the truck is running only? When the key is on? Is it hot all of the time?
Ford 6.0L Power Stroke Diesel :: Batteries Get Discharged To A Certain Point / Alternator Not Charging
I ve been noticing that the alternator isn't charging correctly, or at least it seems like it. We drive short trips sometimes two times a day, a mile or less. One day, night actually, I noticed it started to not turn over with it's usual enthusiastic sound. When the batteries get discharged to a certain point, the voltage at idle will be less than 12 volts. If I rev the engine for a bit, the volts jump up, but at idle it drops back to 12 or below. Seems to me that it should be at least 12v or above if the batteries are discharged, and more towards 12.5ishV if the batteries are fully charged.
After I put it on a 6A charger overnight, the voltage upon starting is above 12, sometimes over 13. But if the batteries start to dwindle down from short trips, the voltage drops to 12 or below at idle.
I did install the smaller pulley a few years back, and that worked massively. I couldn't get 12V at idle before installing the smaller pulley. But now it seems like I'm back to that same situation before installing the smaller pulley.
So, I m guessing that a alternator bench test is in my future? The batteries are fairly new, tho they have been down to nothing at least twice from boneheaded moves by yours truely!
And, I'm speculating that this charging situation contributed to the recent FICM replacement that I went thru.
Ford 6.7L Power Stroke Diesel :: Installed New Batteries - Door Lock Fuse Blown Again And Again?
I just bought the batteries I was asking about in this posting. Bought them at auto zone on my lunch hour today, they swapped them out right there in the lot, no problems. Watched carefully to make sure terminals were not crossed, etc. When I came out of work a few hours later, the #20 fuse for door locks was blown. I chalked it up to the battery change, and put a new fuse back when I got home. I come out an hour later to leave, and the fuse is blown again. I have not replaced it again, need to go get more of the proper amp rating.
No other changes to the truck other than the battery replacement. And that's the only anomaly. No other problems, nothing. Getting ready to head cross-country on a skiing trip, this Friday, so there really is no time to get to the dealer to get this looked at.
Ford 6.0L Power Stroke Diesel :: 2004 F350 - No Crank But Will Only Start When Jumped Even With New Batteries
I went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 RepliesFord 6.7L Power Stroke Diesel :: 2011 - Battery Hold Down Tray On Driver Side
Whose bright idea was it to have the damn tray attached to the puke tank making it impossible to remove by itself? What am I doing wrong?
I'm replacing my batteries and one of the hold down bolts slipped down off the tray underneath it somewhere. I removed all the bolts holding in the tray and find that it is attached to the puke tank?! (Coolant reservoir). How the heck to I get to that bolt?
Ford 6.7L Power Stroke Diesel :: 2011 F250 - Dead Batteries - Starting Attempt Results In A Faint Click
This is my first dual-bat vehicle. 2011 F250 with ~60K. Dual alternators. Bought in August of 2010. One battery(passenger side) was leaking pretty badly in ~2012 and was replaced under warranty along with the harness as it was corroded.
Yesterday, I drove the truck quite a bit on ~20-25 mile trips and left idling during a couple of them while inside Home Depot. No indication of any trouble.
Today, would not remote start, and when I put the key in and turned it to the on position, the dash lit up for about 3 seconds but once it started waking everything up, it all went dead. Start results in a faint click. I got 11.2V from a trusted meter. I've got my 20A charger hooked to one side right now.
Is there any special trick or attachment procedure to charge a dual battery setup? What about jumping off? Does one bad battery cause both to "act" bad? If I can determine which battery is causing the issue, am I safe to replace just that one, or should I get two new batteries?
Ford 6.0L Power Stroke Diesel :: 2003 - Cough / Sputter For A Few Minutes With No Power After Long Crank
So, a year ago or so I had the truck die on me, it would start after cranking it a long time and cough/sputter for a few minutes with no power. I thought it seemed like a weak hpop or leaking oring, so I tore it down and put it all back together with a something or other hpop. Now I have a no crank no fuel pump condition, the injectors don't cycle when I turn the key on, I do get relays clicking, but no start, the yellow/blue wire gets the starter to turn over, but no fuel, so couldn't start if it wanted to... I am getting 120 ohms (like 122) on the dlc 6,14 and millivolts, basically nothing between 4 and 14...
I sent the ficm off to get rebuilt and they told me that it was already good (charged me anyway though, ah well...) I wiggled wires around and pulled my ficm plugs apart and pushed the wires in some, didn't seem to move any... What is next? There can't be that many things that cause all three, No Fuel Pump, No Crank and No Injector Buzz, can there?
Ford 6.0L Power Stroke Diesel :: Long Crank After Night Sit?
I'm having a long crank cold start issue. It takes about 2 five second cranks before the truck will start up. It just started acting this way yesterday before I fired it up to go to school. After its warm it fires up no problem the rest of the day, just takes a bump of the key.
I don't think it's the GP system as this truck has started at -20 to -25C all winter long unplugged with no issues. From my reading some sources say that it could be a HPOP leak, maybe dummy plugs?
Is there any way for me to do some more diagnosing - places to look or test for? There are no stored codes other than an EGR code due to the delete. Truck is completely stock with atlas 40.
Ford 6.0L Power Stroke Diesel :: Long Cranking When Warm / Pressure Too Low
Some information about the truck2004 Excursion, Motor has a December 2003 built date listed on the valve cover
Bullet proof complete by Hallas performance just prior to Mike's passing (3 years ago). ARP, EGR, Oil Cooler, lifters, etc..
Newer batteries, DC amp 185 alternator, newer starter, she cranks hard and fast~230,000 miles
Here is the situation: Starts good and fast when cold, even subzero temperatures. She cranks long and barely catches if I make a short stop at a store or restaurant. A few hours later or the next morning is fine.
I found the following codes:
P2284 - Injector Control Pressure Sensor Circuit Range/Performance
P2291 - Injector Control Pressure Too Low - Engine Cranking
P0528
I took her into the local Ford Dealer for diagnosis and here's what they reported. ICP tests good and has the latest pigtails. They reported a leak in either of the following.
Oil injection pump Estimate of 8.5 hours to repair.
Under the Valve Cover Gasket. Estimate of 3.5 hours to repair.
So here are the questions I have. Does this diagnosis sound appropriate? Is it reasonable that they do not know which area is causing the problem? Are the hours reasonable estimates for the repairs? Assuming I go ahead with these repairs, is there anything else I should have them look at while they're in there?