Is there a way to check to see battery health with Dashboss? I know I can check charging system, but is there a way to monitor if the batteries themselves are going south on me?
View 5 RepliesI had a bad Glow Plug on my 2004 F350 6.0L Diesel causing the check engine light to go on. I replaced the Glow Plug and cleared the OBD2 error. The check engine light is off now, but I can't pass the smog check because EGR Monitor "Not Ready"
I put 100+ miles city/freeway miles on the truck, but I still get EGR Monitor "Not Ready" Even tried "Drive Cycle" with no luck...
Noticed the other day when I went to leave a job site my Check Engine Light came on but the truck started fine and seemed to run normal. while cruising down the highway I noticed that my factory boost gauge was showing 35psi and fluctuating between that and around 10. looking at my H&S it was showing normal boost readings for the current driving condition, when I came to a stop the H&S would show 0psi but the factory one would fluctuate between 0 and 35-40psi..
I can tell the turbo is not spooling at all during this time. if I take off from a stop with the gauge showing 35 the engine sounds louder than normal at first take off compared to when the gauge is reading normal. I haven't gotten a change to get it in my shop yet to look it over but does the dash gauge read from a different sensor that what my H&S is reading? Truck is an '11 F250, deleted both EGR and DPF with H&S tuner. I checked codes and all I have is P06A7. Where to start?
My 04 F 350 started with a check gauge light while going down hill towing an 18 ft car hauler full of mulch. Did it for 5 seconds, then when we got to our land and I was getting ready to back up it did it again. and this time my oil pressure gauge was at zero. I shut her down. checked the oil. its full. Drive home everything is good. Today I'm getting fuel pressure gauge going nuts. 80 to 100 PSI. at idle no oil pressure and the check gauge light. but the engine is still running. Oil was changed 4K ago. fuel filters same. Where to start looking?
View 5 RepliesI have a 2003 Excursion 6.0. I didn't post this in the 6.0 section because it may not be just a 6.0 issue. (See what I get) On cold starts, anything under 150 degree water temp reading on the SGII. I get a CHECK GAGE light on accompanied by the check engine light. No codes read on the SGII pending or stored. Just some of the time I get a water in fuel light too. This tends to go out fairly soon after driving. (Even after I just drain the fuel pump it still happens.) other issues that accompany the lights are as follows.
The trans temp does not give a reading to the dash. The oil temp does not give a reading the dash. Both show proper temp on the SGII. When in reverse the back up alarm beeps as if something is behind me. And the auto door locks will not activate after 10 mph. The tach also will not show a reading in the dash. SGII shows the numbers. Now the kicker, this ALL gets resolved the instant the water temp hits 150 degrees. The only lingering issue is the that the tach will surge or drop every now and then. The tow/haul light does not come on when this is going on. I've checked the battery terminals all are clean. Both batteries are brand new.
Driving my 2003 today seen the "check gages" light on and the trans temp gage pegged on hot. CRAP, tranny time! look at the edge evo and it reads trans temp as -60F ???. Plugged in the torque pro and it reads 8,240F. At that point I figure its PROBABLY not that hot. Let it sit for a while and back to normal. Watch trans temp on torque pro as I drive it and everything is fine till it gets to about 150, then it jumps to 60F, then 30F, the 8240F. The cooler lines and trans pan are both feel normal. Picked up a new temp sender on my way home.
View 5 RepliesMy batteries go dead over night, had them checked but they say there good, can't figure out what's causing them to die.
View 8 RepliesMy 2014 350 DRW has a battery problem......If it sets for a couple hours, it won't start. With a jump from a very small battery box, it starts right up. I charged it last week for 4 hours and still when in OKC it would need to be jumped at each restart. Do I have one of the batteries going bad.....
View 6 RepliesI didn't drive my truck for one day and the batteries are died. This is the second time this has happen. That is a pretty fast drain time. THe truck only has 2500 miles on it. And I;m talking the batteries a dead dead. I hate having to take the truck to the shop. Just a big inconvenience. And it only happens about three weeks apart. I bet that would be pretty had to find the problem.
View 5 RepliesAbout how long do batteries hold up in this truck? I ask because in my 06 6.0 it was an annual event 2 batteries and an alternator.
View 14 RepliesIf I'm giving a jump:
Assume I hook positive and negative cables to the respective terminals of one of the two batteries. The alternative would be hooking positive cable to one battery and negative cable to the other battery, or does that make 24 volts? I'm also assuming if it is just the one battery, it does not matter which one you jump from?
If I'm receiving a jump:
I assume positive cable to positive post of one battery and negative cable to a good ground under the hood somewhere? Again, does it matter which battery I use? I wonder where a good ground is on this crowded diesel engine and aluminum body. Front radiator supports?
In the last 2 months I've replaced my starter and 2 new batteries. I've tested the alternator and it's fine. What more is there? I'm guessing the FICM is going to crap. If I attach a scangauge 2 to it now would it tell me if that's the problem?
View 14 RepliesI have a 2000 watt inverter and I want to connect it to my 2011 F250 Super Duty. Which battery do I connect it too. This will only be used every once in awhile.
View 12 Replies2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
I have both a hydraulic dump trailer with two 12v batteries and an RV trailer with two 6v batteries to supply 12v. Both trailer's batteries are wired to be charged from the tow vehicle if the TV is equipped with a charge line.
Does the OEM 7 pin connector on a 2005 Ford 6.0 F250 CC 4X4 have a charging line on it? If so which terminal / pin is it?
What gauge of wire is it and how much amperage will it deliver to the connector? For testing, when is it hot? When the truck is running only? When the key is on? Is it hot all of the time?
I ve been noticing that the alternator isn't charging correctly, or at least it seems like it. We drive short trips sometimes two times a day, a mile or less. One day, night actually, I noticed it started to not turn over with it's usual enthusiastic sound. When the batteries get discharged to a certain point, the voltage at idle will be less than 12 volts. If I rev the engine for a bit, the volts jump up, but at idle it drops back to 12 or below. Seems to me that it should be at least 12v or above if the batteries are discharged, and more towards 12.5ishV if the batteries are fully charged.
After I put it on a 6A charger overnight, the voltage upon starting is above 12, sometimes over 13. But if the batteries start to dwindle down from short trips, the voltage drops to 12 or below at idle.
I did install the smaller pulley a few years back, and that worked massively. I couldn't get 12V at idle before installing the smaller pulley. But now it seems like I'm back to that same situation before installing the smaller pulley.
So, I m guessing that a alternator bench test is in my future? The batteries are fairly new, tho they have been down to nothing at least twice from boneheaded moves by yours truely!
And, I'm speculating that this charging situation contributed to the recent FICM replacement that I went thru.
I just bought the batteries I was asking about in this posting. Bought them at auto zone on my lunch hour today, they swapped them out right there in the lot, no problems. Watched carefully to make sure terminals were not crossed, etc. When I came out of work a few hours later, the #20 fuse for door locks was blown. I chalked it up to the battery change, and put a new fuse back when I got home. I come out an hour later to leave, and the fuse is blown again. I have not replaced it again, need to go get more of the proper amp rating.
No other changes to the truck other than the battery replacement. And that's the only anomaly. No other problems, nothing. Getting ready to head cross-country on a skiing trip, this Friday, so there really is no time to get to the dealer to get this looked at.
I have a 2006 F250. Past two winters my batteries have died. Last yr., bought 2 new batteries and a new alternator. This winter, battries have been replaced twice. I only drive the truck maybe once a week, about 5 miles total. I live in Indiana and we have had many sub zero temps this yr. Its been in the shop all week, the mechanic states that they are finding an extremely small draw but cannot find where it is coming from. The mechanic is wondering if I am driving it enough. Any thoughts on this? Also my batteries came from auto zone, the mechanics thought it was bad that I had bought them from auto zone.....not sure if that should even be a factor....
View 14 RepliesI went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 RepliesThis is my first dual-bat vehicle. 2011 F250 with ~60K. Dual alternators. Bought in August of 2010. One battery(passenger side) was leaking pretty badly in ~2012 and was replaced under warranty along with the harness as it was corroded.
Yesterday, I drove the truck quite a bit on ~20-25 mile trips and left idling during a couple of them while inside Home Depot. No indication of any trouble.
Today, would not remote start, and when I put the key in and turned it to the on position, the dash lit up for about 3 seconds but once it started waking everything up, it all went dead. Start results in a faint click. I got 11.2V from a trusted meter. I've got my 20A charger hooked to one side right now.
Is there any special trick or attachment procedure to charge a dual battery setup? What about jumping off? Does one bad battery cause both to "act" bad? If I can determine which battery is causing the issue, am I safe to replace just that one, or should I get two new batteries?