Should the upper fuel bowl be empty after sitting for 30 minutes?
I believe no. Which would indicate to me a stuck open injector which Iv been suspected of. Iv been trying to track down a miss that I have and Iv been suspicious of a bad injector but ain't been able to pinpoint which one yet.
2003 6.0 no start. turn the key to on and nothing happens. dash lights up as it should but I don't hear the glow plugs cycle and no fuel gets into the upper fuel bowl. turn the key over and nothing happens. No starter click nothing. tried the starter wire to the battery trick and it cranks but does not kick over. checked ficm wires and they are secure as well as the injector wire on the intake manifold. it is the original ficm.
View 6 RepliesI have an isspro gauge and did the blue spring about 5 years ago. Since then my fuel pressure is in the 65psi range.
Last week it dropped to 50-55 normal driving and I figured the HFCM was on it's way out (195,000 miles). Replaced the HFCM and the pressure was a bit higher, but not back to it's usual range. Then pulling the boat home from the lake a couple days ago, I saw it at 45psi. On a couple hills it went as low as 40 psi, so I was getting gripped...coasting downhill it only went back up to 50 psi and no higher. Got 'er home and currently not driving it.
In garage with Key On Engine Off, during injector buzz, I can hear a hissing/air noise at the upper filter bowl. Also, the bowl drains empty once the pump cuts off and the sound of air stops too.
I am hoping it's a regulator issue, but I don't know if they are known to wear out or go bad, or if something else in the upper filter housing went bad. So I ordered a new upper fuel filter housing which also has the oil filter tower attached and I'm assuming that these new units would come with the blue spring upgrade already done.
I can check for codes tomorrow when I bring my computer home from work, so I haven't checked for codes yet. I pick up the new filter housing tomorrow and will periodically check back here during the day tomorrow.
Also, while I'm at it: the new HFCM doesn't have the heater. Can I just leave the old connector from the harness un-connected to anything?
2004 F550 with a 6.0. I had to clean out my fuel tank, replace the HFCM and filter on top of the engine. When I start the truck it will run for 30 seconds or so, start running rough then die. I opened the cap on the fuel filter housing on top of the engine to make sure the fuel was getting there. I turned the key on and the fuel bowl quickly filled up.
After a short time however, the fuel drained out. To where I do not know. I don't think this is normal as every time I've changed the upper filter on a 6.0 it is always full of fuel. Why could this one be draining out and could that be the issue why the truck dies after starting and running for a short period of time. I changed the o-ring on the cap and the new HFCM was purchased from Ford.
I've thought I smelt diesel fuel on an off for a while, but never found the source.
Tonight, 17 degrees out I have fuel in the valley and it appears as if the back of the drain valve is wet.
A fuel bowl rebuild is on the short list. Is this typical, the cold weather brings the issue to light?
I have an 06 f250 w/ 6.0. Having a no start problem. If my truck is warmed up and sits for 5 min or so and try to start it, it starts fine. If it sits longer than that , no start. But if I wait about an hour and a half, it starts right up. Why would it not start if sitting for between 10- 90 min. Starts fine cold.
View 14 Replies (E350 van)... I smelled diesel fuel inside the van tonight and used my flashlight to investigate the leak. The cover around the blue spring is damp.
Before I remove every again to gain access to the filter housing to fix the leak, what I am may encounter. Seems like a good time to do the blue spring upgrade. Can I access the egr valve to inspect and clean?
What are the possible areas to check for the leak? Sometimes finding little problems leads to finding big problems. When my FICM went out I discovered the battery terminal clamp was broke.
fuel gauge does what it wants? It goes down to half way then goes back to full or sometimes even empty. Not a big deal for me because I have gotten used to it. But I would hate to have my wife in here and she thinks it's good and run out.
View 14 RepliesThe installation of the new 50 gal. Titan tank went well overall. Start up was smooth with no leaks but the fuel gauge is showing empty with about 45 gallons in the tank.
The sending unit was properly oriented ("clocked") so I'm guessing the electrical connector is not secure at the top of the sending unit. Not sure I can reach the connector without lowering the tank somewhat.
My fuel gauge acted pretty weird today. When I left my house today it was just above half a tank. I was sitting in traffic quite a bit and then looked down and it was below the e. I knew it wasn't empty so I kept going. Got to work. Went for lunch and it said full drove about 5 mins to eat and it went down to half a tank. What's going on? I am thinking of the fuel sender or wiring?
View 3 RepliesFuel gauge goes back to empty when I fill the truck all the way up. It goes back to full once I have used up 2 gallons ( from 36 gal to 34 ) on my 2012 F350. I also had a similar issues years ago with my 2003 6.0L .....
View 4 RepliesI had to drop my fuel tank and as a result, I replaced the fuel lines from the underbed filter to the tank. After replacing everything, I purged, purged, and purged some more. With much difficulty I was able to get the truck running and it ran good. But, I have trouble restarting the truck anytime I let it sit for a couple of hours. It cranks and cranks and eventually fires, but with much difficulty.
View 12 RepliesNew to me early 99 (4/98) f350 7.3 6 speed. Truck started acting up a few days after I bought it. Return line at fuel bowl was leaking, so started there and found a bad seal on the Fpr (unrelated to the fuel leak due to disentegrated compression sleeve). Fast forward through a bunch of parts swapping that still resulted in miserable lift pump pressure readings, I pull the sending unit out of the tank, expecting to find a plugged screen.
Well, there was in fact a plugged screen... Attached to the bottom of an in-tank pump. How did that get there?!? Everything I've read says there should only be a pickup tube??? Should I get a new sending unit from a junkyard and do the hutch mod or???
Trying to fit my edge fuel pressure sensor. I have a 90* fitting from Diesel O-rings and I can't seem to get the 90 elbow to turn all the way down before it makes contact with the fuel bowl housing. I'm using the drivers side port, should I use the passenger side port? would it have more clearance than the driver side port?
My instinct is to crank it all the way down then tighten the nut, should I just screw it in until it makes contact then tighten the nut? I was worried it wouldn't have enough threads in contact to seal as well as it should and leak.
I want to build a fuel bowl delete/regulated return fuel system for my 2000 f250 . I would like to make a really neat kit and attach all products used so people that want to build their own would have a useful source. I understand that it will probably cost the same but I want to design my own and route it the way I want . I have 3/8 1/2 5/16 and 1/4 stainless tubing as well as a bunch of unions and 90* 45* fittings and a couple tees. What size is the ports for the fuel lines that go into the four corners of the heads . I am a pipe fitter pipe welder by trade so this is basically a mini version of what I do everyday at work. Looking for some size details of the head port sizes so I can get the correct fittings?
View 3 RepliesI've had an engine oil leak for some time. Recently I've had to add about a quart a month. I got some fluorescent dye and added it to the engine oil last time I added a quart. Ran the engine for a few weeks. Then cleaned the engine valley with cleaner and hot water.
Tonight I investigated the top of the engine with a black light. To my surprise, the oil leak is coming from the fuel bowl, right around the drain valve. I can clearly see about a drop every 3 seconds of fluorescent yellow liquid falling into the valley below and yellow all around the valve.
I expected a leak from the HPOP not the fuel bowl. Do I have a bigger problem? Is engine oil getting into the fuel? I plan to replace the seals in the fuel bowl, but not until I know whether I have a larger problem to address.
2001 F250 Crewcab, 220,000 miles
I have a 1983 Nissan Sentra with a Hitachi carburetor. The fuel in the float bowl seems to drain completely after sitting for 48 hrs. Is this normal? If not, what is the solution to preventing this fuel loss?
View 7 RepliesHad the ole factory fuel separator/bowl drain start leaking on me about a month back. So i ordered and installed a new one, issue fixed. Well last night the fuel leak started again, I looked everywhere and i cant see anywhere else it may be leaking at. I felt the underside of said piece and it didn't feel wet, but the valley is full of fuel.
I got in there and tightened the 4 bolts down some more, they were tight but i got a some turns on em and am hoping i either didn't tighten it down enough or they maybe backed out some. Now just gotta see if that solves the problem, again.... the replacement is a doorman, the o-rings were bigger/thicker than the factory orings on the old part, of which the o-rings were shot.
Like I said once i replaced the part the leak stopped for 3 weeks until last night. If the tightening of the bolts doesn't solve it where should I look next? I have an FRX mod but i checked all that and its dry as a bone around all the fittings by the bowl and the heads. No indications of leaks anywhere around any of the FRX assembly.
I have a 2005 f250 6.0 diesel. I have changed the 2 fuel filters, fuel pump, sending unit (was broke off in tank )and installed the blue spring fuel pressure regulator kit. My truck will run for a few minutes loose fuel and kill. Could this be a sensor or computer problem
View 12 RepliesI just changed the drain valve on the fuel filter bowl. All went well and no more leak, but now I am getting an "emission system" warning light.
After I replaced the valve, I filled the fuel bowl with diesel fuel. Was there any other priming that needed to be done (if any)? What the emission system warning light may mean?
2002 F250 7.3L 4x4.
My A/C will blow cold for about 3 min. and then stop for 10 min......then cold again for 3 min.....then warm for 10 min.......what is going on ? It does this when on climate control and on A/C . I had a compressor go out about 1 1/2 yrs. ago due to a fan failing...the compressor tore apart... This is not acting like that though .
View 9 Replies