Ford 6.0L Power Stroke Diesel :: Turbo Replaced - Oil Coming Out Of Exhaust?
Nov 8, 2016
Had a bad turbo on my 07 F550 with a 6.0. Replaced it today and took her for a ride. Started smoking and oil was spitting out of the weep hole in the muffler. A lot of smoke. The truck was smoking before I replaced the turbo too but I didn't have any oil coming out of the weep hole. I'm hoping it is just oil that had been passed into the exhaust by the bad turbo that is now being burnt off and pushed out by the new turbo. Does this sound plausible?
View 1 Replies
Advertisement
I have a 2011 that does not currently have the complete factory exhaust system on it and no muffler. With the nice weather I have been driving around with the windows down and hear a noise out of the exhaust that sounds like tires spinning on wet pavement when I let off the throttle or at some shifts of the transmission. Boost seems normal, and don't hear any noise while under load. I think it is just the VGT closing and making the noise. With deleted sys heard this noise in exhaust?
View 4 Replies
I have 07 F350 6.0 never heard this out of any of my 6.0s. it's almost a whine but can hear it w turbo and out of empty exhaust. Almost like a supercharger noise stumped almost leaning towards actuator for turbo? Noise got real loud swapped turbos used same actuator noise is there but much quieter.
View 1 Replies
For a while now, I have been hearing a very high pitch whistle noise from the turbo/exhaust area. Everybody told me it was an exhaust leak, but I never could pin point the leak. While I was under the truck last weekend I found the flex joint on the passenger side up pipe was broken a leaking.
I ordered a Dorman replacement pipe that comes with a new gasket and hardware.
I will be the first to admit, I am not a fan of Dorman parts... BUT, this pipe is really nice. It looks identical to the pipe being sold on Dieselsite.com, it doesn't have the scoop inside to direct exhaust gas to the EGR cooler and it comes with all the mounting hardware.
[URL] ....
Once I got the turbo down pipe out of the way and soaked the bolts with penetrating oil, I had the broken up pipe off in 30 minutes.
View 8 Replies
Having this problem, what to do to correct it? There is no hole in the boot and this just started about a year ago. Does not do it all the time.
View 4 Replies
This is is a truck I hardly know anything about. My wife bought it while I was deployed for herself and when it comes to vehicles she's an idiot. No, really she told me she bought it because at horse shows everyone else has one.
I noticed an oil leak and had a reputable shop look at it. They told me it was coming from some seals on the turbo. Long story short there is a brand new turbo on there, stock replacement. Now it seems very under powered and shifts hard. Pressing down anything more than 25% throttle will cause hard shifting or no shifting at all. It'll stay in second until I ease off the throttle.
I tried searching a few terms but I'm not sure what to look for. I don't know if someone has messed with the tuning. Broken clamp on the turbo. Replaced and everything is back to normal...
View 4 Replies
So for the first time in a while I started my truck when it was cold outside, 33 degrees according to the truck. It didn't do this at initial startup but when i started driving there was what i think steam coming from the exhaust because it dissipated fairly fast. It steamed slightly until i went to pull out of my neighborhood and got on it to get up to speed which was only 45mph. The oil temp was in the 90s at that point but when i got on the pedal the truck just started pouring white steam out of the exhaust.
Over time the truck warmed up and the steam stopped and everything was fine. Even when its warm outside the truck blows something when its not at operating temp but when its warm I can only see it at night when there's headlights behind me. Since I've had the truck the only thing that I've had to replace was the radiator because it was leaking coolant and even after that i still smell burning coolant occasionally and sometimes when i check my tank its low and then sometimes it never changes. Its very inconsistent.
The only other bad thing that's happened to the truck happened after i got my oil changed for the first and last time at NTB. They replaced the filter when they changed the oil but didn't pull the old gasket off when they put the new filter on and long story short i lost about a gallon within 30 minutes because of that and had my truck towed home. My engine light never came on or anything. I fixed the problem, added new oil and that was it. The reason I bring up the radiator, the coolant, and the oil is because i don't know if that could have anything to do with the steam.
View 10 Replies
My friend is working on a 2004 6.0 F-250 and it has used 75% of the coolant in the overflow bottle in 5 days. Can't smell coolant either. The inside of the tailpipe is wet soot black and there are wet spots on the tube coming from the intercooler to the turbo at the turbo and the intercooler. He's thinking EGR cooler.
View 6 Replies
2005 6.0 & noticed on Friday there was white smoke coming from exhaust that started when I'd turn on truck then aster 1st light or stop sign it would be a cloud of white smoke. Once I start to drive it stopped & I didn't see it again that day. I noticed the same thing again on Saturday & Sunday but the smoke was thicker on these days but would stop like the day before.
I had a code come up a month ago which I believe was P404 but read something about EGR valve. So I replaced the EGR valve 3 weeks ago & light never came back.
Today I had a Dr's Appointment and had usual white smoke in morning but once I got to the Dr's appointment the truck sounded like the turbo got louder then usual and started to see cloud of white smoke again. While sitting in parking lot I check to see any codes but nothing came up but the cloud of smoke started.
When I left my appointment, the turbo sounded louder still and noticed white smoke every single time I stopped at a light or stop sign.. Then the coolant level was high with the engine giving me the warning of over heating coolant or something like that.
View 2 Replies
I just looked back and it has been since July 7th that my girl has been sitting in my shop. Well this past weekend I finally got her back together and started. It took a while to build pressure but she finally came to life..
While I am thrilled that she is running again i have low power before the boost kicks in and is idling rough with a blueish- white smoke coming out of the exhaust. Once i kick her a little she will get up and go but I've never had the smoke before.
I'm thinking maybe a bad injector???
View 3 Replies
Having trouble with 6.0 powerstoke white smoke out exhaust. We have installed egr delete and still have white smoke and water coming out of exhaust not as much as before. Took it back apart to see if we did anything wrong everything look ok. We did a compression test on all cylinders they check out ok.
View 6 Replies
Lately I have noticed a lot of blueish smoke coming from my exhaust at idle mostly while warming in the morning though it would do it if the truck idled for a few minutes. I took it to the dealer because I have fords ESP but the tech couldn't get the truck to smoke and wasn't getting any codes so he sent it back with a clean bill of health. After getting it back I noticed it smoking again so I picked up the egr valve kit pulled the valve and cleaned it as best I could and replaced the seals, that was last night. This morning it was blowing more smoke than it has before and has continued all day whether cold or warm. I just changed the oil last week and it's still full so it isn't burning any. Head gaskets were done along with studs last month, egr is obviously intact, cat is gone. I'm really at a loss for this, It's an 07 f350 scsb 6.0...
View 6 Replies
I noticed a rough idle after driving an hour with a 6000 lb trailer and stopped at an offramp. Had no performance issues to that point in an hour drive. Then I noticed a good amount of white smoke coming out of the exhaust. The idle felt just like when I had a contribution/balance code on #5 a year ago, and a new injector fixed that. Before long (10-20 minutes later) the idle got real loud, like a big knock/loud tick every revolution.
I had a bunch of stored codes, so I reset them and later found a P0281 - Cylinder 7 contribution/Balance and P0404 - EGR control circuit range/performance were the 2 that came back. I drove it 2 more hours to get home. It ran well under load, but coasting or stopped gave the loud knock, and stopped and idling was a rough, inconsistent idle. It even stalled on me 3 times when braking for a red light (auto trans). There was a lot of white smoke all the time, plus a little dark smoke on acceleration.
What would you recommend for troubleshooting steps? I could put a new injector in #7 and clean the EGR valve, but want to have a good idea that will fix it first. Is there a good chance I have a messed up piston in #7 now?
Codes I cleared:
P0148 Fuel delivery error
P0234 turbo overboost (i know i need to pull and clean the turbo anyway, unrelated to today's issue)
P0281 Cylinder 7 contribution/Balance
P0404 EGR control circuit range/performance
P0670 Glow plug (I had the module unplugged a while ago)
P0683 Glow plug (I had the module unplugged a while ago)
View 14 Replies
2007 F550 with the 6.0. About 2 months ago I replaced the EGR cooler with a Bulletproof cooler. Truck ran well for a few weeks. Then I started getting the "turbo fart". I stopped using the truck until I had an issue with another truck. I was stuck so I sent the 07 out without cleaning the turbo. This morning a decent amount of white smoke started coming out of the exhaust. The smoke would sometimes get a bit gray. Going up hill it didn't have much power at all.
View 8 Replies
Today I drove to dinner in my 2012 6.7 with no problems then on the way home my brother said he noticed my truck was white smoking quite a bit and he said there was a very strong exhaust smell coming from my truck ( he was in his car behind me) I ran a diagnostic test and what came up was code P0401 (I believe that's right). Need to figure out what is going on with my truck before I take it to the mechanics and get charged up. The truck still has DPFs in it just has a DPF back exhaust and has a AFE cold air intake running on a stock tune. However I do have the DPF deletes and EGR delete sitting in my garage just haven't gotten them on the truck yet.
View 2 Replies
I'm looking at maybe trading for a 2004 F350 with a studded and deleted 6.0. It has a "thumping" sound coming through the intake like an exhaust valve is staying closed. My question is, how common is it for the rocker arm retainer or rocker itself to fail? It has 204k miles, and the owner says he was on his way home about 2 weeks ago and it just started doing it.
View 3 Replies
Newbie hear to the 6.0L's. But I'm learning an awful lot really quick from all of you here. I've read lots of tech stuff on these EGR Coolers, oil coolers, FICM tests. This is what I got happening right now.
2004 F-250 6.0L. Today was 45 degrees in Reno. 5400 ft elevation. Tried to start it without block heater. Would not even crank. It tried to crank but sounded like it locked up on first crank. Tried again, nothing. Same. Tried yet again and finally got to getting the engine to crank, but wouldn't start after about 5 seconds of cranking. Waited a little while not wanting to burn out my FICM, then tried again. Same as previous, would crank but not turnover. Checked batteries. Both were over 12.3 V cold, motor not running. This next time, turned key on and let it sit in ON position for about a minute. Then cranked and it took about 5 seconds and then the motor finally cranked over. Lots of black smoke as usual for a cold start like this. Battery volts after cranking over and running were now both over 13.6 V.
Keep in mind the truck has started better than this before in 15 degree weather just about a month ago.
After it started I noticed what appeared to be oil/coolant residue directly underneath trucks transmission area. It was not tranny, but in that area. I got under the truck and can see this fluid coming from EGR Cooler area.
Now for the smoke. Just stared smoking on start up. White smoke. Then it would disappear as engine warmed up. Now its constant white smoke when warmed up and applying the throttle. Smells like coolant coming out of exhaust. Not diesel.
I parked truck facing downwards on my driveway. Then I checked EGR Valve. When I pulled it it was WET. Not dry. Peeked in EGR Valve hole, didn't see coolant. Just wetness. I did change gasket and rings on it the day before as well.
As for FICM, it reads 47.9 Volts on key turn, 48.1 on cranking and 47.8 running. FICM good by all standard 6.0L literature. Degas bottle passed pressure test holding near 15 PSI for 20 minutes! No oil in degas bottle that I can see.
Truck is stock. Is my egr cooler and oil cooler shot? Would a bad egr cooler or oil cooler cause this awful cold start? When I plug in the block heater, it starts NO PROBLEM, but still white smoke. Also, NO loss of power at any time.
View 6 Replies
I've been mulling over the idea of doing a muffler job on my 2002 f350 7.3 cc short bed. I do tow on and off for work and dual material for work. I am thinking of upgrading the exhaust because I noticed a couple small leaks in the muffler and I'd like to lower the egt's for the truck so it breath a bit smoother. I'm not a fan of the really high pitched sounds I've heard on some I want it deep and heavy sounding. The turbo is fine for now but eventually I'll need to know what to upgrade to once it starts to wear out. I don't plan on doing dumb chips or tunes because it's not a toy truck but a work and daily driver.
View 10 Replies
So, I just got my turbo back from my pal Ruben at SoCal Porting (does good work fast and inexpensive) and, I have a question about the exhaust housing with the EBPV.
Is there a gasket that goes between the turbine housing and the adapter that the down pipe mounts to? And, if so, what is the part number for it? If it's steel to steel cool. If not, I'd prefer to put the OEM gasket in there versus permatex or something similar.
Pic of the compressor housing with a little port work....
View 3 Replies
Weird thing happened today. Was out running errands, and upon pulling out into traffic I felt the truck lag a little. I figured it was the typical trans hiccup we all experience from time to time. As I continue driving, I notice I don't have any turbo boost.
I'm cruising around 55-60 and when I slowly give it gas......No boost. I stomp it and the turbo gauge slowly climbs to about 12 psi. At this point I waiting for the truck to throw a warning message and none came.
As I'm reaching my destination, the speed limit is 30 so I'm just putting along and any acceleration I did, the boost needle wouldn't move. I arrive at the store, and when I got back in 5 minutes later and drove off, My boost was back. Truck operated normal for the 25 minute trip home. I thought a similar thread was started but I couldn't find it.
View 14 Replies
My truck is all stock and I am running in performance tune? And my friend the former owner said I need to let her loose about 75 percent of the time I am driving it because it's my DD and I do not tow anything on a regular basis. I do not want to stretch my bolts by unnecessary pushing, I don't know if I'm even pushing it hard but I normally get the turbo up to about 30 psi is that to much?
View 8 Replies
