Ford 6.0L Power Stroke Diesel :: Truck Turns Over Just Fine But Won't Fire With Codes
Jan 28, 2015
Got up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
View 11 Replies
Advertisement
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 Replies
I bought a 99F350 with a 7.3, it was not running when I bought it. Batteries good, new starter, turns over just fine, fuel pump works, but now I don't know what to look for.
Was testing ohms for my injectors and at the plug on top of the driver side valve cover, couldn't get a reading at all, tested the ohms at the pass. Side valve cover plug and got good ohm readings.
View 14 Replies
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 Replies
I've noticed it takes my truck much longer to start recently. I have 2 brand new interstate batteries, just changed both fuel filters and my truck still takes a good 10 seconds or more of spinning over to fire. Is this normal? I don't remember my truck doing this before, it usually fired right up even in winter. Could this be an injector or glow plug issue?
View 13 Replies
Just bought a 13 6.7 used. It is in excellent shape but, you turn the key off and it is a few seconds before it dies? Is this maybe something aftermarket the previous owner installed?
View 8 Replies
OK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 Replies
My 2006, 4.2 has been really erratically not starting. Turns over fine but will sometimes fire up and tries to run on maybe 2 cylinders, then stalls. Now it won't even do that, nothing. No check engine light or codes. Guess what the thing started up this morning 7 degrees out and running like a charm. Turned off and nothing again. Replaced relay for PCM ,no change, still no codes.
View 9 Replies
My f250 was parked this winter to get work done. I had put a new exhaust on and while crawling on the engine bay it had kicked the fuel reset by the passengers kick panel. After pressing that button the truck would not start and threw FICM codes. (Power low to FICM) and my Scanguageii had said that power was very low (27 volts) during cranking. I sent the FICM to FICMrepair.com. Today I had put the FICM back into the truck and went to start it. I cycled the plugs 3 times and started on the 4th. The truck did not start after this and had thrown more ficm codes. What it could be?
View 12 Replies
This isn't my truck, but I'm trying to diagnose it for a friend and I haven't seen it. He's scanning it with a high-end Matco scanner so I'm not convinced that the scanner is reading right but here's what I've got:
P0056 (2), P0161, and P0300 (random misfire detected). The first two are "gasser" codes and don't show up in the 6.0 bible code list so I'm wondering if they were added in to some of the later flashes??
The truck has a "new" OEM turbo and won't build over 18 psi of boost but, according to the owner, who is a decent mechanic, it's absolutely clean inside. Looking for about the weird codes it's throwing?
All my years of information on 6.0's was stolen with my laptop last year ....
View 13 Replies
Owning a 2001 F250 Extended cab with a 7.3 I have not had a lot of questions to ask fortunately.
My truck has spent a lot more time sitting than running lately and when I went to start it the other day it cranked fine but would not fire. Quick read on this forum and the first thing I found was how if the fuel solenoid had less than 10.8 volts when cranking it would not start.
I went down and checked the battery voltage and it was at 12.1 volts no load. I put the battery charger on for about 10 hours (time to kill) and when I pulled the charger and cranked it over, started with no problem.
View 3 Replies
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 14 Replies
I have a 2005 f250 just hit 180k last week and it has the 6.0 in it, egr deleted, sinister diesel oil cooler, stc livewire tuner with street tune installed, air raid air intake. Wicked wheel 2 in the turbo. Its throwing codes P0606 and P0341. Cam sensor has been replaced and the other code is a mystery to me. Its been randomly shutting off like you turned off the ignition all day today.
When it stalls it takes 3-4 times to get it fire back up. When you first go to start it the pressure gauge reads 0 but once it fires up it says theres pressure. Also some of the days it never stalls and runs like a champ but other days i cant drive more the 10 feet and then it stalls. I have no idea whats going on with this truck and ive put lots of money into it doing customization and stuff like that so I am hoping that its not on its last leg....
View 11 Replies
I recently caught up on some maintenance with my truck, changed the turbo pedestal seals, replaced both batteries, brakes, e-brake cable etc and installed new 10k hid headlights. its a single cab 250 with a 7.3 and zf6 4x4 with 133k. a couple days ago I turned on the headlights and the truck died, restarted no problem and would die the next 5 times I tried to turn them on, then it worked fine. yesterday I got in my truck to leave for work and got no wait to start light, no glow plug chatter, no fuel pump running. turns over just fine but no fire.
I got a ride to work and tried it when I got home, fired right up. I pulled the pCM, checked it out, no weird smells and my TS chip wasn't corroded or anything like that, worked fine. drove to 711 to get a 6 pack and it did the headlight thing again. I removed the HIDs because this all started after I installed them and reinstalled my silvanias and it didn't die when I turned them on. this morning went to leave for work, same no start condition. I disconnected both batteries for 30 seconds to reset anything and same problem. I was about ready to light it on fire this morning.
View 1 Replies
I have a 99 F450 bucket truck. I was up in the bucket when the engine died suddenly. It turns over but won't fire. I have no dash warning lights now either but everything else seems to be working. Lights, radio, annoying beeping sound from the key left in the ignition, etc. There are roughly 5 or 6 fuses in the panel to the lower left of the steering column that don't have power to them. Are they all supposed to have power when the ignition is on? I checked the fuse panel under the hood and all of the fuses that have 12V to them are good. There are a few small ones that don't have power to them but I don't think they do all the time.
View 9 Replies
I just replaced the glow plugs, gpr, valve cover gasket and harness. When cooled down, cranks but won't fire. Smoke DOES come out the tailpipe. If I plug it in for awhile it fires right up. What else can I do or check?
View 5 Replies
I have a 2003 Silverado 1500 V6 vin code x with 260000 miles, for about a week now in the morning when its damp out or when it has rained the truck won't start, it cranks fine but will not fire. once it sits for a few hours and everything drys up it fires right up with the first turn of the key.
View 3 Replies
Truck is a e99 f250sd 4x4 7.3 manual trans. The truck started and ran fine to work this morning. Went to leave this afternoon. Hopped in, put key in and tried to start it. Engine just turned over, never started. Thought that it didn't start because I didn't let the plow plugs warm up enough. Turned ignition off, turned back on and let wait to start light to go out. Same thing happened again. Just turned over but wouldn't start. As far as I can tell the fuel pump is running. Felt it vibrating while the ignition was on. What to check.
View 14 Replies
Last night I bought 2000 F250, 346k on it... Crew cab short bed 4x4 with ranch hand bumpers like I wanted .... Headed back home (Miami FL ~1100mi) and covered about 200 miles @70-75mph before i ran into few problems ....
First off, while cruising I noticed slight hesitation in the throttle, with loss of speed regardless of pedal pressure, noticeable on inclines. It would go away on downhill and get smooth response again and pick up speed. This went on for about 40 miles.
Then I noticed heater blower stop blowing hot and start blowing cold, without me changing any settings. At the same moment, I noticed temp gauge move up and I hit next exit offramp to check what's up. During right turn at the end of off ramp truck stalled. Pulled to the shoulder, and popped hood.
Noticed empty degass/overflow bottle. Carefully opened lid and water gushed up to the top. When all pressure slowly released, water pulled down and emptied the bottle. Both upper and lower radiator hoses are empty. Engine oil has no traces of water tho. There were no leaks under the truck. I then tried to fire up the truck to get me to the gas station 1/8th mile away.
No crank in Park. WTS comes on and goes off. Cranks in Neutral, RPMs come up some, oil pressure shoots up to normal running position, but won't fire. Tried a while then gave up as not to kill starter and batteries completely.
Fuel pump works 20 sec then shuts off. There is fuel in bowl. I covered 140 miles since last full fill up, so not fuel pickup issue I don't think.
Summary
Have crank
Have RPM
Have oil pressure
Have fuel
Have (had) batteries, now not so hot
It's cold out ....
View 14 Replies
Drove 40 miles took half hour then back in the truck and drove to lunch. When I got out of the truck you could smell burning. Opened the hood but there was nothing to see. Coolant level in the plastic hold tank good checked oil level, okay. No sign of smoke but the smell was real. Went in had lunch and came out and nothing. no smell nothing. Drove fifty miles home and nothing every thing working perfect and no smell. Oil temp. 197 to 203 all the way home.
Only thing that was done on truck was last Tuesday Ford did oil change.
View 14 Replies
So I've had my 2003 F-250 power stroke 6.0 for over a year now and replaced the oil with AMS oil which is good for 50,000 miles to a year as well as the oil filter which is guaranteed the same thing. I've only put 5,000 miles on it since I've owned it and made sure to let the engine heat up before going anywhere as well. Recently my engine bogged down and then had problems starting I was able to limp the last 2 miles to work but haven't been able to get it running since.
I replaced the camshaft position sensor and it fired up but once it was running it the rpm gauge dropped below 1000 RPMs it would stall out. Before it didn't have any smoke coming from the engine compartment however now when it starts it does. Is this because there's oil the possibly leaked onto something or fuel? What do I or should I look at to get it fixed?
View 6 Replies
