Ford 6.0L Power Stroke Diesel :: Truck Shut Down While Driving / Code P2614
Apr 13, 2017
So a few day ago my truck shut down while driving. I posted up and checked the ficm harness as suggested. Things were a bit lose so I zip tied my harness around the ficm. Thought it was all fixed and test drove it and it shut down again. I tried to start it a few times and my ICP was a tad low about 450 ,I have a brand new ICP and harness. Checked my scan gauge and I have code p2614. I cleared the codes and the truck started right up. I need to get this sorted out I was supposed bro go home tomorrow from working out of town all week about 100 miles from home...
View 3 Replies
Advertisement
I drove the truck Sunday to 3 different places, parked it around 3:00 pm. Went to take it to work the next morning and it just cranked with no start. I pulled the codes as I have an edge insight. I got a P2614 code so I figured it was the cam sensor. We after some reading to what everyone had to say I checked to see if I had RPM when I got home and I did so that put me back to having no clue. I took as many readings as I could to see if any one might see something that I am not.
ICP psi 1280 cranking 23 key on
IPR 41% cranking 14 key on
IPW ms 0.00 cranking and key on
Fuel Pressure 63.1 cranking
ICP voltage 1.6 cranking .3 key on
Mass Air flow 8.3-10.7 cranking 0.00 key on
Engine RPM 166-205 cranking
FICM 47.0-47.5
View 14 Replies
So I am out of town about 120 miles from home on a job. I was driving down the mountain road to the store and my tuck just shut down. Lucky for me I was able to get into a turn out. So I try to start the truck and it will not fire. I check for codes I am getting p2614, p2617 so I was able to clear the codes and get back to the house I am staying in. What is going on with my tuck. Oh ya the code did not come back on in the 15 min drive to the house. Also just finished up doing a y pipe and my egr o ring so I and the intake and all that off.
View 4 Replies
I am getting ready to go on vacation this weekend with my f350 and I was driving today when suddenly the truck shut down while going at about 25 mph. I tried to start it and it just kept cranking. I got it started 5 mins later and it threw a P0069 code. I drove for about 2 more miles and it shut down again, and started right back up. I'm guessing map sensor? This was the last thing I needed to happen!
View 14 Replies
Just got this injectors done. Filled the tank up. Drove for 1/4 of a tank. Went to leave out yesterday. Made it out of my subdivision and down the road 3 miles or so. I was going 55 when the truck stalled. I tried to start the ignition it would turn over, but wouldn't catch to stay running. I did this at least 8 times. Friend came with Ether. Tried 3 separate times, truck started going dead. So i was about to give up... Tried it 1 last time, it fired up like a champ!
View 6 Replies
Just to give you a run down on my truck. It's a 06 F-350 4x4 supercrew 6.0 with 78,994 miles. The trucks has been studded with Apr and aftermarket head gasket, Powermax turbo with a wicked wheel, RCD EGR delete kit, 5" turbo back MBRP exhaust, Driven Deisel regulated fuel return system, high REV valve spring kit, EBT sensor, 58volt swamps diesel FICM, edge evolution, within the last 4000 miles New oil cooler, crank sensor, cam sensor, IPR valve, ICP, batteries and lift pump. I think I'm missing a couple things but that's the layout.
Now for my problems recently took the truck to Florida from Illinois towing a 8500# boat. Before I left I had the oil cooler changed, Rotella T6 5w40 ,New filters And 2 bottles of REVX. The try k didn't miss a beat on the 1300 miles trek down. It sat for 3 days before coming back up lite truck. I was gonna drive straight thru and with 1100 miles down and 200 to go the truck acted like it was running out of fuel and died at 90mph. Fuel Gage read 1/2 tank to go.
After letting it site a 1/2 hr it finally fired back up and drove 5 miles before doing it again. This went on 3 more times. I even limped it to fill up the tank thinking the gauge was bad. Nope did it again And called for a tow truck. This was in mid october and 20 miles ago. Since then I've replaced fuel filters, lift pump, IPR, ICP, cam and crank sensors, sent the FICM in to have tested, replaced batteries. No the problem is worse. It Now has created a serious miss when it's cold till 90 then it Idles smooth but keeps dying on me like it did when it was towed.
View 14 Replies
What could be making the strange pumping sound coming from under my hood after I shut off the truck?? It sounds like a small compressor or pump running.
View 4 Replies
I noticed when I shut off the truck about 30-40 minutes later I'll open the degas bottle cap and notice there is no pressure.
I used a coolant pressure tester kit and pumped in 16PSI but couldn't hear or find the leak.
I'm going to buy a smoke machine in a month or two but until then, can I still drive the truck ?
I'm guessing it is a pin hole leak somewhere as once I shut the truck off... there is a lot of coolant pressure.
View 7 Replies
So today I was driving down the highway and my engine shut off. No sputter or any thing I had just filled the tank. I tried to start it and it wouldn't start. It's been hitting a dead spot at around 3000 rpm like its not getting enough fuel or something. Right now I'm thinking it's an ipr valve but would like to know if what was the cause and how did you fix it...
View 10 Replies
Been chasing my tail and can't figure out an electrical issue. My issue is that I'll drive for about 20-30 min and the truck will shut off while driving. I'll pull off the road, let it sit for 10-20 min (cool down) and It will fire back up and go for another 15 min or so. Sometimes it will glitch/wig out when i try to start or not start....
I've replaced the following and monitored everything on a scanner.
-cam sensor
-crank sensor
-2 new batteries
-flashed the ecu
05' F250 6.0 King Ranch 4X4
View 5 Replies
A Little Background, my FICM wasn't bad per se but it would dip below 45 volts when the outside temp was around freezing. I pulled it and sent it for repair at the same time the Atlas 40 tune was loaded into the FICM.
First few days of driving mileage was better, truck ran great. All of a sudden one day pulling into the driveway it randomly shutoff. Two occasions since it has acted goofy at started, bucking a little a low throttle. Mileage has returned to how it was before I had the FICM fixed and ATLAS tune applied. To this point I had no codes at all.
Now today it randomly throws P0341 - Camshaft sensor out of range.
So heres the question - do I replace the sensor or try to get at the harness for inspection? Out of range would usually mean the sensor itself is failing while open circuit is usually wiring related. I know its uncommon for this particular sensor to fail but i'm not sure which direction to go.
View 7 Replies
I'm almost (1600 miles to go) home from my 8000 miles or so summer trip. More on that after I get home. Right now I'm curious about something that happened twice in the last two days.
Towing down steep grades in tow haul, truck downshifted and RPM went up but I don't think it passed 4000 and it didn't seem any higher RPM than many other downshifts. But, wrench lit up and truck threw an over rev code.
View 9 Replies
I just pulled over when my truck flashed reduced power. Pulled code and it came up poo88. What to expect?
View 3 Replies
My wife returned home and stated that my excursion stopped running twice while she was driving it. She said both times were as she was letting off the throttle coming downhill an off ramp. Both times it fired right up and drove away fine.
I pulled the codes using torque app and it showed a p1211. Unfortunately I had just screwed up my gauge settings so I really didn't have any gauges set up so I couldn't use it. (It's for the 6.0 anyway).
After some Internet searching I am guessing it's an issue with the icp or ipr. How do I tell which one to replace? Truck does have a dp tuner normally set to 80 economy tune.
View 11 Replies
The first time it happened, I wasn't monitoring any PIDs as I didn't have my phone with me. Not really sure if I hit a bump or anything, it just stalled. I pulled it off to the side and put it in park and started cranking. Turned over rapidly but wouldn't start. I started freaking out thinking what am I going to do? Shut the truck completely off and waited a couple minutes and then turned the key and it started right up. Drove to my destination and didn't have another issue.
I'm only driving my truck on weekends as I have a company van and I can't park my truck at the condo I'm living at right now. So sometimes it's a few weeks between drives. This has been the story of my truck use since I nought it 3 years ago. In fact I know my turbo is sticking as the most boost it builds is 20-22 psi. I probably have a sticking injector too, as it smokes unburnt fuel until warm.
So the last few weeks when driving, I've noticed that if I hit a big bump, occasionally it dies again. What I've discovered is that it won't start unless I shut the key off entirely. Meaning, if it stalls I put it in neutral as I coast, shut the key off as far as it will go and it will start up. If I just throw it in neutral and try to start, it won't.
Watching my Torque Pro display, I've noticed that it locks up (like normal when I shut the truck off w/o shutting the Torque app off). The display then has read lower voltages than normal for FMP, FLP, FVP (main, logic and vehicle? can't remember ). FMP is normally at 48.5v and the other 2 hover around 13.9v. The last time it stalled, I noticed 9.3v for FLP and FMP was 23.4. I'm not sure if this is what it shut off at or if I panicked and tried starting it w/o shutting the key off entirely. So please don't take those readings as gospel.
I scanned it for codes, but nothing popped up.
View 14 Replies
I just had my thermostats replaced in my 6.4, and I'm concerned about the regent process. I read that when the P0128 code is thrown, truck will not go into regen. Is this true? How can I manually start the regen process?
View 1 Replies
This morning I went to go to the corner to buy something, I knew it was colder than usual, -12F. I did not plug in the pre-heater last night. I let the truck idle for 15 minutes before moving it. It was still idling high. The P0087 code is the only code popping- is this just because of the cold temp? I haven't owned a diesel since my '79 Rabbitt, and this engine is as different from that as night is day. this didn't happen yesterday but it only got down to -2F and warmed up to about 18F.
View 6 Replies
P0237 code. The truck is a 2003 f250 with an edge evo . The truck will run great then throws this code and won't build boost of over 11 psi. Now it even drops it right off to 0. I replaced the map sensor a month ago and doesn't seem to have fixed anything.
View 2 Replies
Can a bad or lazy VGT solenoid cause a P132B code? I just recently had the turbo cleaned and the VGT solenoid replaced about 3 months ago. The truck is a bit sluggish at take off. Is there anyway to check the solenoid to see if its bad?
View 14 Replies
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 Replies
04 with 170k miles. truck runs fine. every now and then truck shuts off while driving. turn it off the it restarts every time. Only code that comes up is number 6 injector. The contribution test injector is firing right. FICM voltage is 47.5. has new ipr and hpop also 6k miles ago. Could it be number 6 shorts out or something crazy killing truck? or maybe a crank sensor.
View 14 Replies
