I have a plow truck that over heats and cuts off. And when it cuts off it won't start till next day? I know the plow has to be low this is not my first plow truck.
View 1 Replies2006 overheats and starts blowing white smoke, smells like antifreeze, added 2 gals of water to make it 1 mile home. Smokes on the way @195 temp and when I shut it off it smokes out tailpipe for another 3 min. Smells like the head gaskets just went, what should I check? The eot and ect have been 10 deg or less.
This has 225,000 miles on it ran great before this, so would it be stupid too not get a redone set of heads while I'm doing the gaskets and studs?
I was thinking of getting heads from here, UCF Machine Shop - Precision machining, engine rebuilding and more. Cummins + Ford Rebuild Specialist. And a Sinister Diesel Complete Solution For Ford Powerstroke 2003-2007 6.0L. Are these the right places to deal with or should I look elsewhere?
I have a 2006 F-250 Super Duty Diesel that I just purchased. Of course there is no warranty and of course I am not that familiar with trucks or cars for that matter. I bought this to tow our 29 ft trailer, which weighs roughly 7000 and should be no problem for the truck. The first 5 times we took it out everything was good and then we took it out and had a short but steep incline and the truck started over heating.
After unhitching the trailer, I drove the truck again and it runs great, no overheating. I even went to the same hill and everything was fine. So, I took the trailer out again and the same thing happened. What this could be? Since I am so unfamiliar with mechanics of things, I really don't want to get ripped off. I have read the troubles with the engine but don't want to spend the 6-8k to rebuild if not necessary.
In the last 3 weeks I've replaced the oil cooler. IPR, ICP, fan clutch, intercooler, rebuilt the turbo, new elc coolant, egr valve, thermostat, new batteries, positive battery cable, and alternator and a host of other crap. Now I have a new problem.
When towing it overheats, almost instantly under load. I was towing a 9k trailer up a hill, a total of about a 30 second climb and it overheated (242 degrees). I'm thinking head gaskets at this point as they are stock and have the tty bolts installed.
I had an issue with my 2011 6.7 this weekend and I'm clueless after doing the google search for info. My truck started overheating after driving it about 10 miles in tow with a light load (20 foot boat). So my first panic reaction is to stop and check the fluids which all check out as good on the levels if I am checking them correctly.
So it cools off and we go for another spin and now that I am paying more attention I notice abnormally high RPMs before it shifts into all gears and that the heat seems to be a by product of this. there is no abnormal vibrations of any type but it sounds like someone learning to drive a standard for the first time.
I does it almost every time. So I tried the manual shift option and it had no problem and no overheat. If it reaches the 6th gear without the overheat alert posting it runs fine but getting there seems to be an issue.
In the back of my mind I do remember hearing this high RPM before but I have a short drive to work and back so I didn't think much about it as I have definitely keyed in on it now. I have only had the truck a year and I do not know when the service was done last on the Transmission.
I have changed pickup filter in tank and cleaned 2 tube filters in tank i thought that would fix it.
View 3 RepliesI have a 2013 that randomly stutters or cuts out for a second while accelerating. This happens whether I am slowly accelerating or full throttle. This used to happen once every few months but it is happening more frequently now. It will randomly happen while trying to accelerate on the freeway. The truck feels like it stalls, then takes off. It feels like it loses boost pressure so maybe a wastegate issue or possibly an EGR valve issue. No codes are set.
View 14 RepliesI have a 2004 F250 4x4 with 204,000. runs great! But last year, I noticed the A/C would work fine to begin with, but after running down the road a bit, it would cut off and I would have to turn it off, let it "rest" a bit, then it may or may not come back on, now I am a electrician by trade, and I figure it is a bad switch somewhere, but a intermittent problem is heck to find sometimes!!!
I replaced the low pressure switch in the accumulator, then I was thinking the little wiring plug might be bad, so I replaced that but it's still doing it. I was going for the relay next, but I'm not sure which one it is and can't seem to find a wiring diagram for the system. I'm stumped on which way to go. Its full of 134a and will freeze you out--- when it works!!
Where the factory BT module is located? The other day while listening to music, I hit a bump and my bluetooth cut out, then came back about 5 minutes later. Almost as if it lost connection to the stereo then reconnected....wondering if something isn't connected securely...
View 3 RepliesLately (within the last year) after about an hour in the truck my radio will make an electrical pop sounding noise and then the sound cuts out for about one second. The pop is not very loud. It will do this about every 15 seconds at first and then after ten or so minutes it's every 1-3 minutes. Doesn't matter the source, it does it on all of them. The volume is at normal (adult ) listening volumes. Interestingly the subwoofer does NOT cut out which points me towards the amp inside the radio. It also seems as if heat may be part of the issue as it takes a while before it happens. If I turn the radio off and wait 15 minutes and then turn it back on it will work for a few minutes and then start popping.
View 14 RepliesJust installed my SCT livewire TS. The truck runs good without a tune but it has egr delete so it had check engine light. So I put a performance tune with egr disabled so it cleared code. But I noticed at pretty heavy acceleration the fuel seems to cut out. Usually once boost builds. Does the same with the street tune.
View 5 RepliesThis truck isn't mine but it's an 05 F250 automatic. We just did oil cooler, STC, standpipes, dummy plugs, EGR delete, and cleaned the turbo. Truck starts perfectly and runs great 99% of the time. But after a high load throttle situation right when you let off the throttle the engine sounds and feels like it cuts out for a split second, then it comes back and everything is fine. It does it with stock tunes but it is more noticeable with his SCT tunes loaded. There are no codes being set. The weird thing is if your drive it relatively easily it never does it, and it never does it while it is actually under high load, at WOT it pulls like crazy until you let off a bit and then it happens.. It also doesn't do it every time but it is fairly often. It has edge insight with fuel pressure monitoring added, ICP doesn't drop out and neither does fuel pressure. What could cause it to do that?
View 14 RepliesWtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 RepliesMy 6.0 with 178k on it just started to have issues today. Low power. When I hit the pedal hard the motor revs and the truck barley moves. When I baby it it goes up to speed and shifts fine. Overall lacking power and not going anywhere. No CEL on. Turbo spools and seems to be ok.
View 5 RepliesFirst post since I bought my powerstroke. I was looking for some diagnostics.
On my way to work this morning and the truck started chugging like it was wanting to die and had no power, the pedal was to the floor and I was barely moving. I was able to nurse it to a parking space at work and pulled the codes, using the Torque pro. This was what I pulled:
P0284 - Cylinder #8 contribution/balance
P0299 - Underboost
P0611 - FICM
P0401 - EGR
P0671 - Cylinder 1 glow plug
On the way home I didn't even hit 5 miles and started into the same symptoms. So I decided to call for a tow, because my commute is about 60 miles one way. In waiting for the tow truck I disconnected the batteries and reconnected them thinking that it might "reset" something. I started it up and the same thing occurred, so I tried revving it up, and starting it up and shutting it down on and off for about an hour. Thinking I picked up some bad fuel. Drove it for a short distance and found things were getting better. I was able to make it home and pulled the codes again. It came up with these:
P0284
P0603 - Internal Control Mod.
P0611
P1000
Also on the ride home I had excessive amounts of black smoke from the exhaust and found a couple of large drops of oil on the driveway where i normally park, larger than what I normally see.
So my question would be what is the cause of all of this?
A little about the truck. it is a F250 CCSB with about 139xxx miles on the clock. I bought it from my brother when he had it he had the FICM replaced (with the 58V option) and the Bullet proof EGR installed. I replaced the fuel spring with the blue one shortly after I bought it.
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesI just pulled over when my truck flashed reduced power. Pulled code and it came up poo88. What to expect?
View 3 RepliesOK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 Replies2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
2011 6.7 with 3.55 gearing. Just got the truck. And it seems when its cold the truck will rev high in 3rd gear and then sort of fall into 4th gear sort of losing power for a split second. If I gas it hard, its not as bad. Usually only happens like I said when its cold. Check the trans fluid its full and looks clean. My guess is some sort of sensor or the computer???
View 7 RepliesIt's a 2004 6.0 excursion with about 190,000 miles. At 185,000 I pulled the motor and did new oem head gaskets, Arp head studs, bulletproof egr cooler and oil cooler system, bulletproof 48v ficm, strictly diesel regulated return, and I've been running gear heads srl tune before and after the truck was rebuilt.
Recently the truck has been acting up at random times. While running the gear head srl tune, the truck will lose power, the boost gauge on my edge insight will get stuck along with Icp psi, the water in fuel light and glow plug light will come on, and then after a few seconds it will clear itself and run fine. Last night I was on a two lane road and putting my foot into it and the truck did the same thing where it loses power, but this time the truck actually died on me while I was cruising at 60.
Same lights were on but this time the cruise control light fluttered while the truck was in the midst of dying. I tried restarting it and it took two sets of cranking before it fired and stayed running. On the way home I babied it and the truck lost power and the Rpms dropped and only the glow plug light came on. Got home and ran codes and I got camshaft and crankshaft position sensor codes and I tuned it back to stock, drove it around, and the truck ran fine, but while on a stock tune I am getting a egr valve code.