My 6.0 powerstroke keeps shutting off when I hit a bump. It's like everything died and reset and I loose all memory to stereo and everything. When I got to work and popped the hood I tapped on the battery cover by the pcm and it shut off again.
View 5 RepliesThe first time it happened, I wasn't monitoring any PIDs as I didn't have my phone with me. Not really sure if I hit a bump or anything, it just stalled. I pulled it off to the side and put it in park and started cranking. Turned over rapidly but wouldn't start. I started freaking out thinking what am I going to do? Shut the truck completely off and waited a couple minutes and then turned the key and it started right up. Drove to my destination and didn't have another issue.
I'm only driving my truck on weekends as I have a company van and I can't park my truck at the condo I'm living at right now. So sometimes it's a few weeks between drives. This has been the story of my truck use since I nought it 3 years ago. In fact I know my turbo is sticking as the most boost it builds is 20-22 psi. I probably have a sticking injector too, as it smokes unburnt fuel until warm.
So the last few weeks when driving, I've noticed that if I hit a big bump, occasionally it dies again. What I've discovered is that it won't start unless I shut the key off entirely. Meaning, if it stalls I put it in neutral as I coast, shut the key off as far as it will go and it will start up. If I just throw it in neutral and try to start, it won't.
Watching my Torque Pro display, I've noticed that it locks up (like normal when I shut the truck off w/o shutting the Torque app off). The display then has read lower voltages than normal for FMP, FLP, FVP (main, logic and vehicle? can't remember ). FMP is normally at 48.5v and the other 2 hover around 13.9v. The last time it stalled, I noticed 9.3v for FLP and FMP was 23.4. I'm not sure if this is what it shut off at or if I panicked and tried starting it w/o shutting the key off entirely. So please don't take those readings as gospel.
I scanned it for codes, but nothing popped up.
I have a 2000 F250 superduty crew cab short box. It has any occasional issue of either just shutting down (engine dies) which seems to happen if i hit an occasional bump. The other issue has happened a couple of times which is it will lose power and just go to a rough idle. I shut it off and restart it and it will run fine. I'm wondering if it is the throttle position sensor.
View 2 RepliesLast week the engine in my truck was shutting off while driving. Happened to me 3 times over the course of two days. The first couple of times, the engine was dead for 3-5 seconds and then the engine would come alive and drive normally again. The third time was about a 10 second event...same result, engine refired on it's own and drove normally. I was in motion all three times so the engine restarts all occurred before I was able to bring the truck to a complete stop.
No check engine light...(I didn't pull any codes because I didn't have my laptop with me). So, I decided to try a new CPS. I had one in my glove box since 2003 so in it went. It replaced a black CPS that I purchased from Riffraff about 100k miles ago. The new CPS seems to have done the trick. I've driven about 500 miles since the swap and the symptom has not returned. I wonder how long this one will last. It's a Ford replacement part so maybe I'll get another 100k miles...
Have a problem with the gauges and radio shutting down sometimes.. Thought it might be a loose wire or something.. But noticed on the scan gauge that it would happen when the volts went over 16 volts.. Is there an external voltage regulator or is it just time for a new alternator..
View 3 RepliesI have a 2003 Excursion 6.0 with edge juice with attitude
While driving first thing in the morning runs like a champ, as the engine warms up I start seeing the exhaust temps lower to 88-94, then I start getting over boost code with monitor reading of 41psi, then the Edge monitor screen will go blank, then the STALL... The excursion with start right back up but the shut off immediately. Wait 20-30 minutes in the shade and will start back up and run again poorly missing almost like turning the key off and back on... Then the next morning start all over again.
I'm thinking bad FICM or bad PMC over heating.. ??
2012 6.7 F250 with 17k miles. It's getting hotter here and the last couple of days when shutting down there is a sound coming from the engine compartment that sounds like an air pump on one of those load-leveling systems. It will go on for about 15 seconds then stop.
View 12 RepliesBrakes seem fine even when the light comes on so I'm guessing its more a sensor issue but which sensor? From researching others posts about ABS lights, seems the sensor on top of the rear differential is a common culprit, but I'm not having an speedometer issues, which also seems to be related to that sensor. It used to be if the bump was big enough to kick the cruise control off, the ABS light popped on as well, but now it's only a moderate bump and it will come on. Shut the rig off, re-start and the ABS light clears, until the next bump that is.
View 6 RepliesI have searched and have found a few threads on various transmission shifting issues. However nothing really pertaining to 13+ trucks that is only happening under certain conditions. It seems earlier trucks with problems were experiencing it all the time, not intermittent.
Here's what I got.... This only happens when:
- temp is 20 degrees or colder
- Truck has been sitting and is cold
- Trans temp under 70-80 degrees
- Only happens on the 3 to 2 DOWNshift when cold
The first few downshifts from 3 to 2 have a slight clunk/bump to them...just enough to feel it. After the first few initial downshifts from 3 to 2, it will not do it then, shifts fine and smooth. After a minutes of driving it, it will not do it until the next time it meets the list of items above. If I skip this gear manually until it has warmed up, it will not do it when returning to it.
-All other gears both up and down shifting feel good just the 3 to 2 when it does happen.
Once the transmission is warm or the temp is warmer outside the problem is non-existent and transmission shifts great in all gears and is smooth as butter!
My 2006 f-250 just started blowing the #22 fuse when i go over a bump! Where the wire harness is for this. I've checked all the harnesses I could locate that looked like they could be rubbing on something.
View 14 RepliesSo with the hurricane coming to my house I did the balljoints on my drivers side yesterday to prepare to evacuate today. Everything went smooth with no problems. Now fast forward to the drive to Orlando, I hit a bump going 65 and my front right side (ball joint replacement side) starts humming. I pull over and it stops, get out see nothing obviously wrong and start back on my way with no noise to speak of. It happened again and again I just slowed to almost a stop and it went away. Yesterday after the repair I took it on a trip through some crappy roads, the freeway, and all that to ensure she was safe with no problems. Maybe it is the bearing failing all of a sudden (it looked fine when I took it off). I have had a vibration at 55 consistently i think is the tires now that I replaced the ball joints (was waiting to have the tire shop check balance until after the repair) maybe that could be it?
View 3 Replies4450 - Literature Program 09L02: Customer Maintenance Reminder
Some owners of certain F-Super Duty 250/350 4x4 vehicles have experienced severe steering and front wheel vibrations and oscillations after traveling over a bump or dip in the road. As a result of a study with NHTSA regarding shimmy, Ford sent a Customer Maintenance Reminder letter to owners back in March of 2009. In addition, Ford agreed to send reminder letter to owners.
Although there is no service action required by the dealer, customers will be informed if after setting the tire pressures on their truck to the Ford specified levels, they believe the vehicle needs additional service, to contact their local Ford dealer. Letters will be mailed starting the week of 12/09/13 and may result in increased customer service inquiries.
Wtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 RepliesMy 6.0 with 178k on it just started to have issues today. Low power. When I hit the pedal hard the motor revs and the truck barley moves. When I baby it it goes up to speed and shifts fine. Overall lacking power and not going anywhere. No CEL on. Turbo spools and seems to be ok.
View 5 RepliesFirst post since I bought my powerstroke. I was looking for some diagnostics.
On my way to work this morning and the truck started chugging like it was wanting to die and had no power, the pedal was to the floor and I was barely moving. I was able to nurse it to a parking space at work and pulled the codes, using the Torque pro. This was what I pulled:
P0284 - Cylinder #8 contribution/balance
P0299 - Underboost
P0611 - FICM
P0401 - EGR
P0671 - Cylinder 1 glow plug
On the way home I didn't even hit 5 miles and started into the same symptoms. So I decided to call for a tow, because my commute is about 60 miles one way. In waiting for the tow truck I disconnected the batteries and reconnected them thinking that it might "reset" something. I started it up and the same thing occurred, so I tried revving it up, and starting it up and shutting it down on and off for about an hour. Thinking I picked up some bad fuel. Drove it for a short distance and found things were getting better. I was able to make it home and pulled the codes again. It came up with these:
P0284
P0603 - Internal Control Mod.
P0611
P1000
Also on the ride home I had excessive amounts of black smoke from the exhaust and found a couple of large drops of oil on the driveway where i normally park, larger than what I normally see.
So my question would be what is the cause of all of this?
A little about the truck. it is a F250 CCSB with about 139xxx miles on the clock. I bought it from my brother when he had it he had the FICM replaced (with the 58V option) and the Bullet proof EGR installed. I replaced the fuel spring with the blue one shortly after I bought it.
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesI just pulled over when my truck flashed reduced power. Pulled code and it came up poo88. What to expect?
View 3 RepliesOK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 Replies2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
2011 6.7 with 3.55 gearing. Just got the truck. And it seems when its cold the truck will rev high in 3rd gear and then sort of fall into 4th gear sort of losing power for a split second. If I gas it hard, its not as bad. Usually only happens like I said when its cold. Check the trans fluid its full and looks clean. My guess is some sort of sensor or the computer???
View 7 RepliesIt's a 2004 6.0 excursion with about 190,000 miles. At 185,000 I pulled the motor and did new oem head gaskets, Arp head studs, bulletproof egr cooler and oil cooler system, bulletproof 48v ficm, strictly diesel regulated return, and I've been running gear heads srl tune before and after the truck was rebuilt.
Recently the truck has been acting up at random times. While running the gear head srl tune, the truck will lose power, the boost gauge on my edge insight will get stuck along with Icp psi, the water in fuel light and glow plug light will come on, and then after a few seconds it will clear itself and run fine. Last night I was on a two lane road and putting my foot into it and the truck did the same thing where it loses power, but this time the truck actually died on me while I was cruising at 60.
Same lights were on but this time the cruise control light fluttered while the truck was in the midst of dying. I tried restarting it and it took two sets of cranking before it fired and stayed running. On the way home I babied it and the truck lost power and the Rpms dropped and only the glow plug light came on. Got home and ran codes and I got camshaft and crankshaft position sensor codes and I tuned it back to stock, drove it around, and the truck ran fine, but while on a stock tune I am getting a egr valve code.