I have researched this online and it seems everyone leans towards a custom tune after this upgrade? It ran like a raped ape before the old stock turbo took a crap!
View 2 RepliesCan a bad or lazy VGT solenoid cause a P132B code? I just recently had the turbo cleaned and the VGT solenoid replaced about 3 months ago. The truck is a bit sluggish at take off. Is there anyway to check the solenoid to see if its bad?
View 14 RepliesDriving back from Baseball tonight, I stepped on the throttle truck was sluggish and a huge black trail out the exhaust. On and off the throttle a few times and no more smoke.
Checked codes when we got home and had p132b. I had this a month ago, replaced the map sensor and no issues. So am I looking at a turbo cleaning? Besides the unison ring, is there a seal and bearing kit? I am at 205k at this point and as far as I know the turbo is untouched.
2011 6.7 with 3.55 gearing. Just got the truck. And it seems when its cold the truck will rev high in 3rd gear and then sort of fall into 4th gear sort of losing power for a split second. If I gas it hard, its not as bad. Usually only happens like I said when its cold. Check the trans fluid its full and looks clean. My guess is some sort of sensor or the computer???
View 7 RepliesThis morning I went to go to the corner to buy something, I knew it was colder than usual, -12F. I did not plug in the pre-heater last night. I let the truck idle for 15 minutes before moving it. It was still idling high. The P0087 code is the only code popping- is this just because of the cold temp? I haven't owned a diesel since my '79 Rabbitt, and this engine is as different from that as night is day. this didn't happen yesterday but it only got down to -2F and warmed up to about 18F.
View 6 RepliesWhat is a "normal" number people see on their load factor? Mine was around 25-30 a few weeks ago but I noticed it is increasing to around 30-40 once I'm in gear, in park it's fine. My acceleration is also getting a bit sluggish too especially going up hills and my throttle isn't responding all the way, my turbo boost is normal though and I don't think there is any VGT stiction. I'm thinking either a fuel filter or a MAF sensor to start with. Fuel filters have been in exactly 10 months. Can a dirty fuel filter, air filter, or MAF sensor affect engine load at idle and how fast it accelerates? I feel like I'm pulling a trailer and with it being more sluggish, my transmission is shifting harder as well.
View 14 RepliesWhen I first start it in the morning and go to take off, It runs sluggish and doesn't smoothen out for the first 1/2 to 1 mile. It then seems to run fine. I have no clue as to what to start checking. The temperature was 65 degrees out, so I don't think that was a factor. I don't know if it's and fuel problem or trans issue, or what. I'm clueless at the moment. It had a recent oil change and fuel filter(s) change. Was doing it before then. 2004 F-250 Super Duty CC 6.0
View 8 RepliesSo after I've been driving for a while and stop at a light or drive thru, I will give it throttle and it seems like it wants to stall. Almost like the turbo isn't spooling and then does and all is good again. Is this a sticking turbo bearing or something else? I am not very familiar with this motor(although I have been doing a ton of searching on here) as I just got it about two weeks ago. I should mention that I am getting the 404 and 405 codes so not sure if that could be involved with the egr?
View 9 RepliesI've come to the conclusion that after 300,000 miles my turbo is sticking. I need to drive the truck up to my mechanic but he's 50 miles away 90% highway (really don't wanna pay the towing bill) would this hurt the truck any more or would it be okay? If it will hurt the truck more I'll get it towed but I'm trying to avoid that at all costs. I have drove it since the turbo began to stick but it is very sluggish and smokes a lot. As soon as I let off the pedal boost immediately drops to 0 psi.
View 3 Replies2003 f250 6.0.... recently did oil cooler,hpop,ipr,icp,fuel pump,egr valve, rebuilt the turbo.... when around 35mph truck seems sluggish and doesnt seem to pick up quick untill i floor it an then hauls butt.. vgt reading at idle is 62% and when floored around 30 to 35%.. fuel pressure is 63psi.. ipr is around 60 to 70% when floored and around 25% at idle. Hpop reading when floored is 3000 to 4000psi and idle is 624psi....
View 14 RepliesI have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 RepliesWtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 RepliesMy 6.0 with 178k on it just started to have issues today. Low power. When I hit the pedal hard the motor revs and the truck barley moves. When I baby it it goes up to speed and shifts fine. Overall lacking power and not going anywhere. No CEL on. Turbo spools and seems to be ok.
View 5 RepliesFirst post since I bought my powerstroke. I was looking for some diagnostics.
On my way to work this morning and the truck started chugging like it was wanting to die and had no power, the pedal was to the floor and I was barely moving. I was able to nurse it to a parking space at work and pulled the codes, using the Torque pro. This was what I pulled:
P0284 - Cylinder #8 contribution/balance
P0299 - Underboost
P0611 - FICM
P0401 - EGR
P0671 - Cylinder 1 glow plug
On the way home I didn't even hit 5 miles and started into the same symptoms. So I decided to call for a tow, because my commute is about 60 miles one way. In waiting for the tow truck I disconnected the batteries and reconnected them thinking that it might "reset" something. I started it up and the same thing occurred, so I tried revving it up, and starting it up and shutting it down on and off for about an hour. Thinking I picked up some bad fuel. Drove it for a short distance and found things were getting better. I was able to make it home and pulled the codes again. It came up with these:
P0284
P0603 - Internal Control Mod.
P0611
P1000
Also on the ride home I had excessive amounts of black smoke from the exhaust and found a couple of large drops of oil on the driveway where i normally park, larger than what I normally see.
So my question would be what is the cause of all of this?
A little about the truck. it is a F250 CCSB with about 139xxx miles on the clock. I bought it from my brother when he had it he had the FICM replaced (with the 58V option) and the Bullet proof EGR installed. I replaced the fuel spring with the blue one shortly after I bought it.
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesI just pulled over when my truck flashed reduced power. Pulled code and it came up poo88. What to expect?
View 3 RepliesOK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 Replies2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
It's a 2004 6.0 excursion with about 190,000 miles. At 185,000 I pulled the motor and did new oem head gaskets, Arp head studs, bulletproof egr cooler and oil cooler system, bulletproof 48v ficm, strictly diesel regulated return, and I've been running gear heads srl tune before and after the truck was rebuilt.
Recently the truck has been acting up at random times. While running the gear head srl tune, the truck will lose power, the boost gauge on my edge insight will get stuck along with Icp psi, the water in fuel light and glow plug light will come on, and then after a few seconds it will clear itself and run fine. Last night I was on a two lane road and putting my foot into it and the truck did the same thing where it loses power, but this time the truck actually died on me while I was cruising at 60.
Same lights were on but this time the cruise control light fluttered while the truck was in the midst of dying. I tried restarting it and it took two sets of cranking before it fired and stayed running. On the way home I babied it and the truck lost power and the Rpms dropped and only the glow plug light came on. Got home and ran codes and I got camshaft and crankshaft position sensor codes and I tuned it back to stock, drove it around, and the truck ran fine, but while on a stock tune I am getting a egr valve code.
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 RepliesI have a friend who is a mechanic for Yellowstone park and he drives a 6.7l for his shop truck that has a utility box on the back with a welder And tools and other stuff, and he claims that the 6.7 has no power whatsoever. He said it does good in 1st and 2nd gear but when u get to the top end it is a serious dog. The trucks he is driving are fleet vehicles and im not sure what the difference is between the fleet ones and privately owned ones if any? What kind of experience with you while pulling? Do they seem underpowered In the top end?
View 14 Replies