Ford 6.0L Power Stroke Diesel :: Transmission Engages Hard On Reverse / Vibration And Some Knocking Sounds On Takeoff
Jul 19, 2015
05 F-350 6L .. Automatic Transmission
When I got the truck I noticed it would slam hard into reverse. Ever since it is taking longer to engage reverse gear and now I have to rev it to 1000 rpms for it to engage with a hard SLAM.
I also noticed that if I do a fast take off, there is a knocking sound coming from drive shaft/differential area (like knock knock knock knock knock then goes away). Then a slight vibration ending at around 30 kph (~20 MPH). There is also some oil leaking from the transmission. I added some mercon sp yesterday - it was a bit low.
My guess for the knocking and vibration is the center support bearings and U-joints. Transmission??? One thing I know I am going to be banging away at that shaft but the transmission problem really scares me.
View 5 Replies
Advertisement
I'm having problems with my 6r140 in my 2011, the truck is an early build around 8/2010 I believe.
After cold soak when shifting into reverse after allowing engine to warm a bit the transmission almost always slams hard into reverse.
After that shifting from 1-3 is awful, the transmission will try to go into 3rd but downshift to 1st then fail to go back into 3rd multiple times. This situation is extremely dangerous when trying to pull into traffic.
Oh and once the transmission gets into 3rd it will skip 4th and go right into 5th. There is only 94k miles on this transmission/truck.
I just bought this truck about a month ago, does this sound like an issue with the solenoids in the valve body?
I'm very mechanically inclined and can swap them if need be but now we're talking few hundred in solenoids and then getting the trucks pcm flashed right?
Also fluid has been changed and I used mercon lv.
View 14 Replies
Late build 03 f350 auto, I got a p0500 code and noticed sometimes after 2rd-3rd gear engages theres a shudder or fast vibration for few secs unless i let off, it didn't start this till i took batteries out, where is the location of the vss at, I am seeing some say at each wheel, on top rear diff, on top back of trans so not real sure?
View 7 Replies
2011, 69,000 miles. My truck is experiencing very hard shifts from park to drive or park to reverse after a cold soak. It goes away once warmed up. I can't find any excessive driveline play and my transmission fluid level appears fine and in good condition.
The last repair done on my truck was around 7,000 miles ago and it was for a transmission fluid leak around the bell housing. They just replaced the seal between the torque converter and transmission.
View 13 Replies
I tow a car hauler that is about 8000 lbs. On my last trip occasionally when the truck would downshift into 5th under a load, it would bang in there pretty hard. Not a smooth transition, not every time just some times. Just wondering it that was normal or the start of a potential issue.
View 6 Replies
I have a new issue that started last Friday. When I put the truck in gear and let it begin to pull itself, drive or reverse, it has a strange jerking or slipping deal. It doesn't happen every time but when it does you can feel it in the drivetrain. I took it to the shop that did the motor work and they ran a diagnosis(while I watched) on the motor and its turns up nothing. It runs perfect, shifts like it always has, but just has this jerking/slipping thing when I let off the brake and it starts to pull itself.
If I go from brake to throttle its fine. I had the rearend diff worked on to fix the leaky ring and pinion seal and the differential cover sealed at the dealer last month. I searched and don't see anything like what I am experiencing. Could my tranny be giving it up now? It has never been overworked and never overheated. I had the full fluid service done at about 70k and now it has about 130k on it.
View 14 Replies
I am using my son's truck this week, 2012 F250, 120,000 miles or so. I left it running in the drive while I got something from inside the house. Guess it was idling approximately 10 minutes. When I put it in reverse the transmission would not shift and the truck didn't move. I killed it, re-cranked it and it went in reverse.
As I was driving down the road the transmission would change gears up and down for no reason. I stopped the truck, and put it in park. I would put it in drive and the transmission sounded like it wanted to slip. I put it back in park and the transmission would not engage. I then killed the truck, re-cranked it, and it drove fine for awhile and started doing it again,
I kill the truck, re-crank it, and we go down the road.
View 13 Replies
I have an 2011 6.7 that has a h&s tuner. Lately my transmission seems to be confused about what gear it should be in when I'm driving about 45mph. It will sometime downshift hard. I have a early build 2011 and heard that it could be a solenoid problem with the transmission.
View 8 Replies
I have an 2011 6.7 that has a h&s tuner. Lately my transmission seems to be confused about what gear it should be in when I'm driving about 45mph. It will sometime downshift hard. I have a early build 2011 and heard that it could be a solenoid problem with the transmission.
View 3 Replies
Everything was fine, running PHP 200X tune, switched to PHP 65 tow and took the 5er toy hauler on vacation last month. Pulled a lot of mountains,etc. While camping, took the truck unloaded to get fuel. Engaged tow/haul going down a mountain to utilize engine braking and the tunes "exhaust brake" and the trans slammed HARD into first gear. This happened twice. I refrained from using tow/haul. Heading home 450 miles with the 5er, I utilized tow/haul again (had it on the whole time, just like on the way down) and the truck and trans were flawless. Get home, switch back to 200X, and I'd say within a week or so, began having trans issues. Loaded stock tune, reset KAM with SCT, disconnected batteries with headlight switch on for a couple days, reloaded 200X and drove it for a couple days. No change.
It felt like the trans was slipping, not "going" like it should when on the throttle, and would sometimes not want to upshift. It would just act "weird". This would usually occur under 40 - 70% throttle (I rarely ever get on it more than that), but sometimes less. Never got any check engine light or tow/haul flashing.
So today I finally did what I should have weeks ago, took off work and ran the truck to a shop.
- First the tech hooked it up to the scanner. No codes.
- Test drove it. He said it drove fine for him. It was fine for me as well, driving it from my house to the shop (I didn't "get on" the throttle though).
- He monitored the voltage from the trans temp sensor. He said the voltage was fine, didn't spike or do anything crazy. He didn't seem 100% positive on this but, said it starts out at 5V cold and voltage should drop as the temp increases, which it did. However, the temp started out at 300 and then dropped to 200 as he was driving. #1 the temp isn't (shouldn't be) that high, and #2 it should increase while driving not drop. The temp shown on my Torque Pro app hit 149 on the way to the shop and 168 on the way home (90 degrees outside). So he seemed to think there was something screwy there.
- While driving it, his scanner showed a trans overheat (over temp/high temp, whatever) code, but no check engine light or tow/haul flash.
- Drove it home. Trans was fine until I got on it a bit and then it acted funny again. But just driving normal with light throttle it is fine.
* Thinking about trying a new temp sensor.
* Could it be in limp mode which is why it feels like it is slipping, i.e. doesn't have the normal power I'm used to?
* When the tow/haul light flashes, is it the tow/haul light on the instrument cluster? That's the only thing that lights up when I'm in T/H. Where you push the button never lights up. Assumed it was just white lettering and not a light.
View 14 Replies
Well I've been towing for almost 150,000 miles with a 2012 6.7 Lariat 4 wheel drive. Things have been going pretty well with the truck. I noticed some sluggish and indecisive type shifts early on but now I'm worried. I depend on this truck for pulling a horse trailer all over the country and Canada. Just recently I've been getting a hard shift or a thump or a clunk when shifting up or down in to second gear. I'm at about 152,000 miles and did a hot flush with LV ATF at about 148,000 miles. Should I worry or keep running?
I have a 97' PSD I'm thinking of giving a nice paint job and a flat bed but am reluctant to do so due to financial concerns and the fact that some folks may not want to see me pull up in an old truck no matter how nice it looks. My tranny temps have been stating under 200F and I really keep an eye on the temps when running up and down the hills while towing. The trailer is a 35' Gooseneck with a max GVRW or 14,000 pounds. Should I wait for the tranny to grenade and then drop in a built tranny and if so who's building these tranny's stronger than stock? Long time no see but this site has always been my go to for all my Ford truck questions, upgrades, etc.
View 5 Replies
I have experienced a hesitation on my truck since I purchased it 6 months ago. I get a one to two second hesitation at take off from a stop. I have checked the back pressure tube and the one that goes to the turbo controller no problems. I have a Edge CTS programmer that only shows ... for EBP.
View 13 Replies
I'm taking my new to me 2011 KR 6.7 I've had it 1 week, to the dealer tomorrow to get them to look at the hesitation on takeoff. I have read on here that not all trucks are doing it. There is 25500 miles on it and have been averaging 15.3 mpg empty, is this about normal for what people are seeing? I'm running the 3.31 gear ad I thought I would get better mpg. This truck was built in Feb. of 2011 would it have the 400/800 settings or would it have to be flashed?
View 14 Replies
I currently have a 2006 F-250 6.0 with 187,XXX.
My problem that i am having is that the transmission recently within a couple weeks started acting weird about the same time 3 of my fuel injectors started failing. When i start up the truck and put it into drive it takes about 3-5 seconds to shift. Once it's in drive it runs pretty well but it will start shifting out of normal when i go to accelerate. Also when i go to slow down sometime the transmission shifts hard to a lower gear. I also have a video of the sound that it had started to make since its hard to describe.
Here are attached videos and photos. I want to hopefully fix the problems myself so i can learn more about my truck. I am going to handle the fuel injectors here soon since 2 are failing and ones about to these have been causing the truck to shudder at around 47-53 mph but after that its fine.
The transmission is stocked and never been altered, i do admit for 3-4 years I have changed the fluids or filters.
The truck is bullet proofed, sct tuner, upgraded turbo from stock, 4" exhaust, head studs and new everything when the engine was rebuilt and bulletproofed.
I plan on going to ford tmw to have them figure out the problem and hopefully its just solenoids so i can fix it myself. I have a link posted also where you can hear the noise it has been making when in R P and when shifting going down the road and it is a automatic.
YouTube.....
View 14 Replies
So loss power on take off and then stopped at store quick shut it down. Came out of store ten minutes later no start just turns over and over. I replaced IPR last year the one on passenger side near frame if that's correct and perhaps this is the ICP near back of engine?
View 14 Replies
So I am not sure exactly what is going on with my truck. It is a 2004 F250 has a 6.0 L. Sometimes when I take off from a stop the truck has no power and blows some black smoke. Then the turbo kicks in and all is fine. It comes and goes when it pleases no matter the temperature. What started happening is when I drive it a steady pace on the highway sometimes the turbo gets quieter and louder and quieter and louder sometimes when it gets quieter I see a little bit of black coming out of the tailpipe. Sometimes it doesn't do it at all. Also sometimes when I let off the gas the truck sounds like it's trying to laugh at me like a wastegate is fluttering.
View 10 Replies
I picked up a 2016 F250 Powerstroke in the first of March. I owned a 2011 before and loved it.
The 2016 has been great so far, but I've noticed a sound that wasn't present in my 2011.
When the transmission is warmed up, I get a "cla-click" sound from the transmission area when sifting from park to reverse. It doesn't do it all the time and I can only hear it, not "feel" it.
This AM I heard a similar click sound when I came to a complete stop. I only heard it while stopping, not while taking off. I could repeat it almost every time I stopped. I was in drive the whole time I heard the click sound while stopping.
What it may be? I know sounds are one of the hardest things to communicate/diagnose.
View 6 Replies
When i take off in morning truck will change from low to 2nd and hesitate for a second and then go on ok. was sitting at light the other day an went to take off an mashed dn on fuel pedal an it just sit there an then took off, dont no whats going on.:-
View 9 Replies
Can a bad or lazy VGT solenoid cause a P132B code? I just recently had the turbo cleaned and the VGT solenoid replaced about 3 months ago. The truck is a bit sluggish at take off. Is there anyway to check the solenoid to see if its bad?
View 14 Replies
06 250 w 65k and it is sluggish on take off, and puffs black smoke most of the time. other than that it runs good.
View 14 Replies
Ok I have a 2004 f250 6.0L, has 104k on it. A little back story... truck was running well when I started to get surging on takeoff and it was blowing black smoke when it surged. After it hit 1600 rpm it would blow out and run normal. So did some research and found it could be the FCIM, I have the 4 pin and tested it and had 48.5v so it tested good. Did some more research and found symptoms leading towards the ICP so I replaced that and the ICR also.
Upon doing this my surging issue cleared up but now I'm getting a miss around 1200 + rpm weather it's in park Reving it or driving, but it is not throwing any codes, I did check with my code reader. I have also changed both fuel filters and have the EBP sensor on order as I hear they can be troublesome. My question is what should I do next or look at? I was trying to avoid the dealer so I can learn more about the truck in diagnosis.
View 14 Replies
