Ford 6.0L Power Stroke Diesel :: Sometimes Just Cranks / No Start
Jan 27, 2016
Like usual, i have a problem that no one else has and it sounds like its something electrical/sensor/PCM related.
Every few mornings, ill go out to my truck and go to fire it up...and it'll just crank away. After i give up on cranking and shut the key off, go to try again, it fires up instantly, like nothing is wrong. Sometimes in the morning itll just have an extended crank but eventually start. Regardless...it always starts. Sometimes it cranks really strong the entire time, sometimes the crank gets weaker the longer you crank...i don't think its HPO related, but i definitely could be wrong.
Ficm voltage looks good KOEO, cranking and running. I had my batteries tested at ford a few weeks ago and they "said" they were good (motorcraft 850ccas). Alternator is strong. When cranking, ive seen the voltage drop anywhere from 10.2 to 9.4v. I never know when this is going to happen and i can't hook up AE every morning and sit and wait, but based on my scangauge, i see ICP shoot up to over 1500 as soon as it fires.
Only code I've gotten is P0148, which is fuel delivery error/engine speed higher than expected. I've gone ahead and replaced my camshaft position sensor with a ford sensor a few days ago...it hasn't done a no-start yet, but it did do an extended crank. I think my next stop is PCM replacement...
View 14 Replies
Advertisement
New alternator, fairly new batteries....after sitting 5 days or more, it cranks but no start.....put on charger for four hours, it fires right up...
Voltage on the multimeter shows 12.45 on both batteries......could there be something drawing down the amps? If so how do I find it?
View 11 Replies
2007 6.0 my dash lights will flicker when the key is turned on and the truck wil crank but won't start, but when the lights stop flickering truck starts .. How to fix the flickering dash light?
View 2 Replies
My truck usually starts up great, but every so often it takes 3 to 4 long cranks before it will start. By long cranks I mean more than 4 or 5 seconds of turnover. Seems to be no real rhyme or reason to this. It does it engine cold or hot. I have iPhone engine monitor app and numbers seem fine. BTW it's a 2005.
View 12 Replies
I got a 2003 6.0 powerstroke cranks but wont start once it gets hot let it sit for a couple of hours and it fires right up already replaced high pressure pump no leaks visible and when running its great will run till run till fuel runs out. what to check?
View 3 Replies
Couple weeks ago fuel tank started coming apart clogged all filters. Replaced tank filters and fuel pump and blew out all of lines. Started and ran fine. Stays plugged in over night but now it'll crank but wont start. No codes showing up or anything...
View 1 Replies
I drove the truck Sunday to 3 different places, parked it around 3:00 pm. Went to take it to work the next morning and it just cranked with no start. I pulled the codes as I have an edge insight. I got a P2614 code so I figured it was the cam sensor. We after some reading to what everyone had to say I checked to see if I had RPM when I got home and I did so that put me back to having no clue. I took as many readings as I could to see if any one might see something that I am not.
ICP psi 1280 cranking 23 key on
IPR 41% cranking 14 key on
IPW ms 0.00 cranking and key on
Fuel Pressure 63.1 cranking
ICP voltage 1.6 cranking .3 key on
Mass Air flow 8.3-10.7 cranking 0.00 key on
Engine RPM 166-205 cranking
FICM 47.0-47.5
View 14 Replies
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 Replies
I have a 2006 6.0 that i did head gaskets on about a year ago. While I was in there I put some new pistons a valves in as well. I finished doing the job and it started and ran great just smoking a little bit. Test drove it a couple of times and still seemed great but still smoking. (white smoke) about a week went by with me driving the truck then one day driving to work I parked it then all of a sudden the truck shut off like some one hit the key and wouldn't restart after that. Either doesn't work i put a ficm in it before the head gaskets went out. new HPOP before head gaskets. I get oil pressure in the dash but it takes a long time to build up. cranks like a dream but doesn't even try to fire.
View 14 Replies
I have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 Replies
I have a 2004 F250 Superduty with the 2003 6.0 Powerstroke inside of it. In the morning i can go out and start the truck perfectly fine starts up and runs like a champ, it will drive to any destination perfectly fine with no issues, ALTHOUGH .... once i reach where im going if i turn the truck off it will not start correctly. it cranks over and will start but sounds as if it is hydrolocking and in a matter of seconds kills itself. once it does this i have to let the truck sit for a minimum of 4-5 hours with the hood popped to allow motor to cool... as soon as its cooled completely i can start it and once again it runs perfectly fine until i turn it off again. if i leave it running at an idle it will sit and idle all day long and i can jump in and drive it fine. It just happens when it gets turned off.
View 5 Replies
2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 14 Replies
I'm TSing a no-start on my 2005 6.0L F250. Engine cranks fine. I've been working my way thru the TSing guide and using my new ScanGaugeII. No codes found. At glow plug warmup, (dash light goes off), I'm getting 40.5v FMP, 11.0v FLP, 14.8% ICP, and 0psi IPR. After cranking for 10-15 sec, get 35.5v, 10.0v, 84.7%, and 446psi. I've had a trickle charger on all night to keep the batteries charged. Have not seen FMP over 45 or IPR over 470.
View 14 Replies
I have looked through every post and idea possible with no remedy for my no start condition. I have tried everything that I am capable of doing without diagnostic computers and other specialized tools. A little history of what happened. While idling in the parking lot for a few minutes, truck all of the sudden start running rough, and acts like it is going to quit. Hurried out of the parking lot to make sure that I made it home, but the the truck would only get up to about 25 MPH, but I finally made it home(about 3-4 miles).
NOW, the truck won't start at all, but just cranks. Some more detail about how it cranks. It cranks fast, I separated the batteries by disconnecting the grounds on each, and made sure both are charged. Batteries are only 3 months old from Ford Dealership. As the engine cranks, oil pressure registers after a little while, (longer the first time for some reason), and as soon as oil pressure shows up on the dash indicator, black smoke starts coming out of the exhaust. The engine is trying to start a little bit, but it mostly just cranks.
Things that I've done: Changed fuel filters, Motorcraft (new orings). At first the pump was pumping large bubbles through the line up into the upper fuel filter, but after sitting it appears that it is not pumping bubbles anymore, and I cycled the Key more than 10 times. Did the bubble test while upper filter was removed. Unplugged ICP sensor. Pulled EGR, installed new one. Pulled oil filter and made sure that oil is pumping.
Checked FICM voltage, with key on Injectors buzzing, also engine cranking for quite a while. Never dropped below 48.5 V. Pulled FICM just incase and performed repair procedure, still same volts and no start. Coolant level is good. Checked oil level. unplugged EGR. Checked filter Minder. checked for chafing on FICM harness. Unplugged MAF. Checked FICM relay operation, Fuses all around. I need this truck to run.
View 9 Replies
Went out to start my truck this morning and it wouldn't start. Cranks fine and almost started once but died. Checked all fuses all my voltages are good. Oil and coolant are good. When I turn the key on I can hear the fuel pump and sounds like it's priming correctly. Might be an issue with a clogged fuel filter? Maybe? Haven't had any problems or issues otherwise.
View 6 Replies
Where to monitor or what to check. The past few weeks this truck all the sudden went from a quick starter(barely hit the key and it would pop off) cold and hot to one that consistently cranks for around 5 seconds before it starts. Doesn't matter if I wait for the glow plug dash light to go out when it's sat for two days or if the engine has a ECT of 198 F and was just running 5 minutes prior...it still cranks over for 5 seconds before starting. Seems like it's an electronic issue vs mechanical, but that's just a guess.
The truck runs, drives and tows excellent outside of this starting quirk...so I know I shouldn't complain but this isn't right from what it used to start like and seems like it's a warning that something is likely to fail down the road. I'd Rather find it now than when 100's of miles from home if possible.
I updated it with better dummy plugs, standpipes, STC fitting, rebuilt FICM, 2 fresh batteries, new fuel pump, ICP sensor all within the last 10K miles. I scanned it with a code reader and found no codes in the history and the check engine light is not on.
Monitoring with a Scan Gauge all inputs seem normal for what I've read on this website with the exception of SYC it says 0? Which should mean it would never start I think but yet it does? I checked my code numbers from the list and I had it entered correct. Is this my issue a bad crank or cam position sensor?
View 3 Replies
So I have a 03 f250 6.0 with 285,000 miles, when I shut the truck off and let it sit for like 20 mins and go to restart it, it cranks then just stops and I hear what I think to be the starter still turning till I let off the key. It'll do this for a while sometimes. So what do y'all think it could be? P.s I know it's very bad for the truck, but I have ran out of fuel about 9 times on the stock pump because my fuel gauge is off, and after the most recent breakdown is about the time it started.
View 8 Replies
2004, DWR, 4x4, 6.0 PSD. One day he started the truck moved it 100' shut it off and the next day it would crank over but not fire. It will fire and run rough if you give it a shot of starting fluid. It shows codes P0401, P0275,P0528, P132B.
View 14 Replies
I just bought an 04 Ford F250 diesel 6.0 with 92k miles. Previous owner installed a UNGO alarm with remote start. Last week, after work, I started it using remote start. I got in the truck and realized I had forgotten something, so I exit the truck and leave the keys on the seat. Truck is still running. The doors lock. I reached in through the cracked window and pushed the unlock button. Here's the problem.. the truck died immediately won't start.. mechanic says it's the high pressure oil pump. I'm thinking it's the anti theft system but no luck.
View 1 Replies
Lately it seems that my 6.0 cranks over longer before it starts. it used to turn over quick and start not it turns over at least 5-8 seconds maybe more. .
View 7 Replies
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 Replies
