I have a 2006 F250 King Ranch 6.0. At approx 45-50 mph when holding accelerator steady, there is a slight jerking like the engine is missing like the old gassers used to do. What could cause this? Have a ScangaugeII and doesn't show anything out of the ordinary!
View 3 RepliesI have a 2005 Honda CRV with 139,000 miles that recently developed a miss. It usually does it while holding steady at 50 mph but only lasts for a couple seconds. If it misses may do it once or twice and then nothing the rest of the day. Had the dealership put it on the computer for a reading and they said it's showing no misfires and is running properly. Plugs have been changed other maintenance performed and have had absolutely no issues until now.
View 3 RepliesTo start off. I have a 2004 F350 with the 6.0 in it which just had a top end rebuild done on it due to the head gasket blowing on it. During the rebuild the EGR cooler was also deleted, ARP head studs, Heads were milled down to make them flat (shop said they had to take 9 thousands off to do so), new up pipes installed, new back pressure sensor installed due to the plug head snapping off, new glow plugs, new glow plug rail harness, oil rail rebuilt due to bad o-rings on the ball tubes, injectors were installed with all new seals and had polished the spool valves hoping to avoid stiction (however its spelled can never remember), and lastly the EGR was deleted electronically with tuner. Also had to get 2 new batteries as they were stone dead and would not take a charge. And had to get a new alternator due to low output. Not sure if the alternator killed the batteries or the batteries killed the alternator either way it needed replaced to.. Unfortunately after i got that fixed i had to get a new starter as it died 3 days later.
Ever since its gone back together Ive had a consistent intermittent miss with the truck. Ive searched every article i can find but seems most complain about misses when cold. Mine is the exact opposite as it only does it once the engines up to normal operating temp. It accelerates hard and fast like it has no issues. While its cold it doesnt miss at all. Once its warmed up sometimes while cruising it will feel like its missing on every cylinder or better description would be as if your driving on a cobble stone road.. If you mash the pedal for a couple seconds till it kicks down and raises the rpms it stops.. Its most prevalent at idle though.. You can literally hear the difference in the engine when it starts missing. Truck will shake as if its got a large lopey cam. Odd part while sitting at idle it will cycle back and forth between running smooth and missing. But same with at cruise as soon as you get on the throttle it goes away. If its doing it while sitting idle at a light, it will take a couple seconds once your on the throttle for it to smooths out. But always does.
Ive tested the Ficm hot and cold, KOEoff and KOEOn.. getting a steady 48v from the main board.. Scan gauge says the Logic boards reading steady 13v... Also from the scan gauge it says my ICP pressure is in the 640 range at idle (full throttle highest ive seen is 3600psi so dont think its a pressure leak) and volts bounce between .80-.90.. but oddly once it starts missing the ICP pressure jumps up 20 psi.. IPR at idle reads 23.5-25.5.. at cruise its up around 45ish.. fuel pressures said to 70 psi.. which its usually around that most times, cruising itll be around 66psi. I had 3 injectors replaced not this past spring but the year before (ironically same symptoms).. Injectors 5,7,8 were replaced then.. ICP sensor was also replaced at the same time as it split and shorted out the connector which was the initial reason i took it in that time since it was dumping the oil on the ground.
I dont have any way to perform a cylinder contribution test and after spending 6K on a rebuild I really cant afford to take it in to have someone else do it. A local guy was able to scan the truck for me but he couldn't do the contribution test either but was able to buzz test them. Everything passed there but we also found some hidden fault codes my code readers did not find. The ones we found hidden said that injectors 2, 4, and 7(again??) are reading low contribution. Of what I've read 2 & 4 sit on either side of 7 in the firing order so have wondered if they're not pulling down 7's results.
I really cant afford to replace the injectors till near the end of next month. Is there anything else I can look at that might actually possibly be causing false readings or intermittent misses only when warm.
1999 F250 7.3 .. The truck seems to idle fine and and runs smooth all the way up top cruising speed, but when it levels out at say 65mph then it starts missing and jumping. I can ease into the throttle a little and it smooths out up until it levels out again.
I have the Vgate Elm and Car Guage Pro and a couple of other apps and the only DTCs I'm getting anymore are:
P0541 Intake Air Heater Circuit Low
P0640 Intake Air Heater Control Circuit
But from what I've read, neither of those should cause this issue.
Buzz test sounds good.
Cylinder Contribution test throws code for #4 Cylinder
I'm trying to do everything possible before throwing an injector in it.
I have a 2012 F-250 6.7L w/8K miles. I have been struggling with this issue for 6 mo. The engine feels like its missing at low RPM. I would equate it to the feeling of a bad coil pack in a gas engine. The boost indicator drops to 0 for a split second then recovers. The dealer says they can't find the issue but went ahead and replaced the turbo. After the turbo replacement It got worse. This is an intermittent problem with no codes.
View 14 RepliesI've got an issue with my truck, I was towing home my camper this weekend and my engine started missing out and vibrating very bad, then it overheated... pulled over and check codes, p0263, p0299, p0300, p0301. Oil all over engine, tons of blow by, definitely a dead miss on cylinder 1. Smokes bad out of exhaust, zero power, and blows cap off of oil filler when loose, tons of smoke and oil from ccv.
My question is, could it be in the valve train? Or is it going to lie in the piston/rings? Blown head gasket? It did overheat, but didn't puke out of bottle, turbo timer kept it running for a bit after I shut it down roadside, egts were definitely high. Also the egr is deleted, have a predator programmer with custom tune for she delete.
There are two bosses on back of hpop cover that have bolts holding heat shroud for the exhaust. How difficult are these to remove? The drivers side looks fairly accessible, but passenger side I am not too sure of. I will be back to disassembling everything in a couple of days, and just getting a heads up on it.
View 5 RepliesI have for a week suspected my batteries were getting weak. just slower cranking is all. I took my truck in to have a viper security system installed and while he was doing his work he killed the batteries. I saw him hook up a battery charger and started the truck. He pulled it around to me and explained how the system worked and off i went. 5 miles down the road, on the thruway, I notice a miss and I'm down on power. FICM looked ok, 48V and it was charging, 13.8 I thought I would bring it to my shop and load test the batteries. On my way here, the check engine light comes on. At the shop, load tested them and they were weak. Installed 2 brand new batteries, started it up, no difference. Hooked up the scanner and pulled a code P2077 (cylinder 6 injector circuit high) Now what? I'm not sure where to go from here. I'm guessing either the FICM went bad or the #6 injector?
View 12 RepliesMy 06 F250 horn would not stop blowing after I beeped to pass a guy. Since I have a toggle switch for my factory/air horn, I flipped the switch to center to cut the horn off. While the truck is running if I engage either horn system it blows. But with the truck off and key out, I can engage either system and it works normally, the horn only blows if you depress the wheel pad. I can hear the relay working correctly, clicking and the horn blowing, but only with the ignition off.
What can cause the horn to blow steady only when the ignition is on? It seems to me the air bag switch is working if it activates correctly when ignition off? I've searched until I am blue, but don't find anything positive and I don't want to throw an airbag at it to find out 800 later the horn still blows. Also, is there a replaceable relay for the horn?
Me and the wife just now noticed this issue after about a week of owning this 6.0 f350 auto 4x4. Leaf spring front and rear. Long bed. Listing all this stuff because not sure if it matters.
Around 50mph if we drive normally about 1500rpm the truck seems to jerk a little as we climb in speed. If we get the truck into the 2000rpm range it goes away.
Not sure if it's suspension, transmission or engine. Any clue what it could be. ???
Here are the basics:
1. Suppose I come to a dead stop or a rolling stop and I continue keeping a small or very small amount of pressure on the accelerator. When I try to start again gently, there are two outcomes: (a) the "hesitation" or "no or dead throttle response," when I had added only a small amount of pressure, or (b) a "lurch" when I add more pressure to counter act the hesitation!
2. On the other hand, if I come to a stop or a partial/rolling stop, and remove all pressure from the accelerator before I start again, it seems I can start from a stop normally, both gently and under control. I have been experimenting by being certain there is no accelerator pedal at all prior to any start from dead or nearly a dead stop. That isn't, however, a fail-safe approach because of various driving conditions.
But, even if that provides a partial remedy, there is still a problem because this isn't the way the accelerator should work. It should not take all that learning, adjustment, and counter-measures to drive safely.
I certainly agree with the another poster: either of the two results of this: the "hesitation," and/or the sudden "lurch," could put the truck in a dangerous situation. I already have experienced this near chaos a couple of times.
So, is this problem continuing to appear on 6.7 2011 Fords, and, if anyone has a 2012---has this problem appeared on the most recently built Fords?
I have a 2006 F350 Crew Cab with the 6.0. It is used primarily for towing a fairly heavy 5th wheel RV. I find that the accelerator pedal pressure is much higher than any previous vehicle I have ever owned. The problem is magnified by the fact that I have a previous ankle injury that makes it very uncomfortable to have to press on the accelerator so hard for long periods of time.
I try to use the cruise, which sometimes works on flat ground, but the shift point at my desired cruising speed is such that the slightest grade will make it downshift. With the cruise off and my foot kept at a constant pressure, the truck pulls up the slight grades just fine with no significant loss of speed and no downshifting.
Is there any way to lighten the pressure it take to push down the accelerator? I know it is actually moving a throttle position sensor, but is there also a pedal return spring here that is too stiff for me?
So, I was on my way back home driving through the middle of nowhere Utah late at night, when I had an injector tip crack. I was able to identify which one and unplug it so I could get to Grand Junction, CO (about 350 miles away) where I have family. After a power nap I started calling parts stores and found an injector from Advanced Auto Parts (I couldn't find a motorcraft reman, but I was restricted for time). Installed it and all seemed good so I hit the road again. However, nothing changed. It still had the bad miss (rough idle, jerking/bucking when the torque converter locks up) just like when I had the injector unplugged.
The truck is an early 2004 6.0. It's the number 4 injector. I finally got home and hooked up my AE scanner to discover a #4 injector circuit low P0270 code and circuit contribution/balance fault P0272. It's definitely missing because disabling it has no effect. This could be a loose connector at the injector or FICM, because I can't afford another injector right now.
i have a 04 ford excursion 6.0 with the egr delete, was stopped at a light to make a left turn, when i stepped on the accelerator pedal nothing happened as the engine was just idling. i pumped the pedal around 10 times and finally got the engine to rev up. i just got this excursion and don't know to much about the maintenance on it. i am going to drain the water and change the two fuel filters. my neighbor is familiar with diesel engines and he said to look at the throttle sensor. i have run this engine up to 900 miles and it has started and run perfectly. i believe the usual maintenance like oil changes etc were done on it. would any error codes show up even though no warning lights on the dash.
View 8 RepliesI have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
Truck is bucking and missing every 10 seconds or so and will stall when taking off in drive sometimes but fires right back up? I got a lot of codes in the torque pro app but some are in grey. Not sure what that means. EGR has been deleted so that's why I got those codes. I was cleaning the back of the truck the other day and found a can of quick start . Guess that might be why i got codes for glow plugs also. I'm gonna post up pic of my codes and numbers of truck running at idle in drive. So far I see I got a code for cylinder 6 contribution? It's in grey tho whatever that means.
View 8 RepliesSo I have just over 14k on my 2015....... I love the truck but have had a few small issues. I had a water leak coming in from the roof that would leak through the grab handle. Nothing major dealer replaced one clearance light seal and they said the windshield needs to be re sealed.
Then I had a god awful irritating squeak in the dash..... It only does it late In the day when it's been hot. The dealer said it was a loose air bag. I have had the truck back a week and it's doing it again.
Those are little issues that will get resolved...... I hate having problems with a brand new vehicle but I understand it happens and that's what warranty is for.
I also reported a bad shake to the dealer...... The truck will shake very violently and have a very loud "diesel" sound. It's very specific at when it occurs. It has only done 4 times in the past 6 weeks including today. The odd thing is the 4 times it has done it has been the same time of day in the exact same spot on the exact same road!!!!
Basically I leave my office sit in some traffic and by the time I get to the parkway it has been35 minutes or so. Only happens in 6th at 60 which is roughly 1,400rpm a slight load due to a small incline and it shakes real bad! The typical "diesel" sound you get when under a load is very pronounced almost to a knock. It will continue to do this as you slowly increase throttle until it down shifts and then goes away. I also caught it doing it and I manually shifted to 5th and it went away.
Because of the rpm at which it happens with slight load only doing it in 6th I lean to a Trans issue and more so a converter problem. It feels like converter shutter. I just don't understand the engine sound.
I gave very descriptive info to the dealer..... Several techs drove it and could not duplicate. I just picked the truck back up last Thursday and the dash squeak is back and the shake happened yesterday and again today. So I am a bit irritated to say the least.
I really hate the fact that I know there is a problem but I also understand if a tech can't duplicate it he can't diagnose it. However today I did get a video of it with my phone so they will know I'm not making this crap up!
2005 ford f250 6.0 Started making this noise from front about a month ago, can't figure out what it is. Only happens when letting off accelerator or changing from P - D. The truck acts normal, seems to be louder when the truck is warm.
[URL] .....
just overhauled my 6.0. run great for about 3 days now runs really rough when cold. new heads injectors rings pistons ficm fuel pump icp sensor ipr valve fuel pressure is good. Engine rolls smoothly when cold also.
View 14 RepliesWhile driving the other day, the truck suddenly began to stall when pressing the accelerator. The water in fuel light came on as did the glow plug light. This continued with the truck sometimes dying all the way and other times just stalling then picking back up. No difference in throttle pressure seemed to make a difference except that letting off totally then slowly pressing seemed to let it keep running sometimes.
So I get home and drain the fuel water separator. I gets about a thimble full of water and lots of the rusty looking junk others have talked about. Try to run the truck again, same thing as before. I then changed fuel filters and thought that had it licked but after about 10 minutes it started again. By the way, the 6mm plug seemed to have about a third of the threads rusted off. Not sure what that means as I drain it at least twice a year.
I have read a lot about the ICP and IPR issues and was wondering if this could be my problem. I am hoping its not the HPOP. My other thought was something in the fuel tank blocking the in tank filter. I checked the top mount bowl and it was only about two thirds full after running the truck
Truck info: Late 2004 Ford F350 Dually 4x4 crewcab, 6.0, EGR delete plate,4" turbo back exhaust with cat delete, no muffler,K&N filter and filter box, Diablo tuner usually set to 60hp upgrade.
I have an 11 F350 6.7. It has just under 200K miles on it. The other day I was driving home, about 100 miles, and my truck's temp spiked. Not like a little spike, but jumped to the 3/4 mark (if there was one) then slowly kept rising to to the overheat mark. I pulled off onto the hard shoulder waited an hour or so to let it cool down, then finished the drive home. All the way home my temp gauge seemed like it was on some sort of drug. It would jump a needle width when I would have to accelerate, then slowly cool to normal after I got up to cruising speed.
Up until this point this truck has been exceedingly reliable. I pull a 13k 5th wheel once a month and drive about 40k-ish miles a year. I also had to refill my degas bottle up to the fill line. Took 2 gallons of Ford VC-3-B Coolant and water mix. After a short run to verify the problem, it took another 1/4 to 1/2 gallon of mix. But, no overheating. No signs of leaks anywhere. Just a strong scent of coolant on shutdown outside the truck. Pressure tested the cap, I don't have a way of testing the system pressure.
Data from Autoenginuity:
Engine Oil temp 195-202 Degrees
Engine Coolant #1: 188.2-199.5 Degrees.
Engine Coolant #2: 125.5-129.9 Degrees.
I have the full CSV file.