Ford 6.0L Power Stroke Diesel :: Size Of Wrench For Battery Terminal?
Jul 2, 2015
I'm not near my stuff--is the battery cable terminal bolt 8mm?
View 14 Replies
Jul 2, 2015
Advertisement
Ford 6.0L Power Stroke Diesel :: Battery Light Has Been Coming On - Alternator Amp Size?
I have a 06 F250 6.0 My battery light has been coming on. Doesn't stay on but I'm planning a trip back east and don't want any issues to occur. I was thinking maybe the batteries. So I stopped at the local Oreilly's Auto store and had them tested. Told the guy what it was doing and he said it sounded like the alternator. He tested it and said it was going bad. He also tested the batteries and said they were good. So I went looking for a replacement alternator and they have different amp sizes. So I'm not sure on what size the original one is and if the replacement should be a bigger size amp wise.
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Battery Terminal Sparked
I was changing out the hydroboost and left the passenger battery connected, the positive terminal on the driver side sparked and now the trucks having a hard time starting? What should I check? Fuse or somthing else
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacement Of Battery Positive Terminal?
Got new batteries installed yesterday and found that the passenger side battery has a nearly broken positive terminal. Had to handle it very gently.
Don't want to replace the entire battery cable just to get the terminal. Using bolt-on replacement terminals? What did you go with and where can it be found?
Ford 6.0L Power Stroke Diesel :: Wrench Light Came On
This morning on my 15 min drive to work my wrench light came on. i don't get over 30mph the whole time. I tired to get the code before i shut the truck off with my sct livewire but it showed no codes with the light on. It didn't drive any different no loss of power. When i checked memory codes with our shops modis scanner nothing unusual came up besides the fuel circuit fault, which i know about the gauge cluster needs repaired every now and then i cant listen to the radio or roll down the windows.
All my numbers on my livewire looked normal. This is the first time it's come on since ive had the over boost issue fixed. What it could be. Kinda of a kick in the pants after i just saved myself a few hundred on wheel bearings and ball joints. Had a grinding noise at different speeds. Couldn't find anything lose on the front end but still had a grinding noise. Ended up being the exhaust shifted and was rubbing up against the frame.
Ford 6.0L Power Stroke Diesel :: EGR Failure - Wrench Light Comes On
So I have a 2006 Ford F-250 6.0 that broke down about 2 months ago due to an EGR failure. Took it to the dealership got it fixed along with a new injector everything has been running fine only thing I notice is a big split in EOT and fW(218 EOT and 192 fWT). Well yesterday on the way home my wrench light comes on I tried to scan it with the scan gauge but it said no codes found and when I got home and turned the truck off and back on the light went off. What could cause this?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On But No Codes
Today on the way home after about 45 min drive my wrench light came on but when I checked for codes on my sct I get no codes. Is that weird or common?
View 6 RepliesFord 6.0L Power Stroke Diesel :: Wrench Indicator Light Comes On Every So Often
6.0l oil cooler going - My wrench indicator light comes on every so often so I after about 40 min of highway driving. So I figured my oil cooler might be going out so here are my temps ....
View 8 RepliesFord 6.0L Power Stroke Diesel :: Wrench Light Comes On - Small Oil Leak
I have a problem when I have been on the road for about an hour or more the wrench light comes on. There is no change in how the truck runs, and when I run a systems check it says that all of my temps are good to go. The one think I have noticed that the next morning I have a small oil leak on the ground on the days that the wrench has come on. The egr valve was just cleaned. I am getting ready to make a trip across the country with a 10,000 lb trailer so I am a little worried about this. Can I take it in to a shop and have them get a code when the light isn't on? Also I am replacing all of the glow plugs this weekend but from what I have read it shouldn't have anything to do with the wrench light.
View 9 RepliesFord 6.0L Power Stroke Diesel :: No Response When Hit The Gas Pedal / Wrench Light Came On
I was sitting at a light and when it turned green I hit the gas pedal and had no response engine was idling perfect and a wrench light came on , I then shut off the truck restarted it and light was off hit the gas it came back on and it was intermittent with taking so I replaced the pedal and it is still doing it...
View 7 RepliesFord 6.0L Power Stroke Diesel :: Non Flashing Wrench Light On Dash
Recently, we took a trip pulling our 5th wheel, even after suspecting another stuck unison ring, sticking turbo issue. When Climbing a gradual grade, we had the "wrench" light come on the dash. The truck seemed to go into the "limp" mode. I pulled over, let the turbo cool down for a minute, and then shut off the engine.
I let it sit for a minute, knowing we were on the freeway shoulder, restarted it without clearing any codes, and it started up without the wrench lit. No limp mode and continued home. I did this twice throughout the trip. I then tried to pull and OBD codes and found none such as a P0299. Seems like there should have been a code saved to evaluate the issue.
Ford 6.0L Power Stroke Diesel :: Wrench Light Comes On Initially / Click Under Dash And Cab Lights Go Off
2006 F-250 6.0l,Auto, 175,xxx mi
When I turn the key to on, I hear the vacuum pump cycle (passenger side fender), but don't hear the glow plugs or injectors cycle. Glow plug light comes on and stays on for 30secs. Wrench light comes on initially, but goes off after 3 secs, but then comes back on after about 8-10 seconds. When the wrench light comes on, I hear a click under the dash and my cab lights go off.
When I turn the key to start, nothing happens. If I jump the starter, engine turns over, but doesn't start. I have check numerous fuses, disconnected the fan clutch, tried moving the shifting lever to neutral, wiggled wires around the FICM/PCM/GPCM with no success.
I tried checking for DTC codes, but my scanner (300 reader) doesn't get any power. I have checked my light, it has power.
Twice before, the truck failed to start like this, but after removing & inspecting fuses/relays (all were good), it started back up. Also, occasionally the truck would stall, (just like someone turned the key off), but would start right backup. But when it stalled, the glow plug light would illuminate for a second,then go off.
Own truck for 8 months, replaced the batteries & injectors 6 months ago. Very light puff of smoke when starting up otherwise ran well when shut off.
How to proceed? My first diesel so I may need some extra details.
Ford 6.0L Power Stroke Diesel :: 2005 - Wrench Light Keeps Coming On Mostly When Doing Highway Driving
I have ran 05 f250 and the wrench light keeps coming on mostly when I'm doing highway driving or when I go to pass someone. iv putt code readers on it(autoparts store readers and the good expensive ones)and i keep getting bad egr and some other codes but when I have the truck looked at everything is prefect I had a flush done on the truck and and it still comes on randomly . Could the fact that it needs an oil change cause the light to come on intermittently or is something else going on??
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Wrench Light Came On While Driving On The Highway
2007 f250 6.0 .... I just had the wrench light come on while driving on the hwy. wasn't towing, or hauling anything. Just traveling around 70mph for an hour or so. I didn't notice any change in power. Got to my destination and cut the engine off. Couldn't pull any codes with an OBD II scanner. When I started it up again, light was gone. Owner's manual points to electronic throttle control, not much else.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Wrench Icon Displaying In The Instrument Panel - Communication Codes
Couple of weeks ago, the display in the instrument panel displayed a large orange wrench. No accompanying text or chimes, just the damn wrench. Checked for codes, nothing out of the ordinary (I occasionally get communication codes, but they usually show up when I do not wait to start). Long story short, the damn thing showed up one more time the same day, then never again.
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2016 - Oil Pan Size?
I'm not anywhere I can look this up, what is the size of the oil pan on a 2016 6.7? I just need the length / width of the bottom of the pan.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Nut Size On Outer Tie Rod?
So what size nut is on the outer tie rod? So far I'm good on the ball joint nuts, calipers, caliper bracket, hub to knuckle (21mm or 22mm--but either way I'm good), and locking hub. I'm putting this all down in my manual so I don't have to guess since i have to load everything up when doing the heavy work.
View 6 RepliesFord 6.0L Power Stroke Diesel :: Injector ORings Size?
What the size of the internal oring is? So far I have had no luck finding the size. I'm looking for the lower housing to body oring.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Carrier Bearing Replacement / Size Of Nut
What is the size of the nut that needs to be removed so I can pull the carrier bearing off the drive shaft? I need to purchase a socket.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Weight Of Motor - Doing Stud - Stand Size?
What is the weight of motor planning on doing studs in future and need to know what size stand and picker to buy. Pulling cab isn't option cus no lift and stand was planning on buying one 2 times the weight so it's good to hold for the weeks to get it done around work.
View 9 RepliesFord 6.0L Power Stroke Diesel :: Bolt Size For Water Pump Pulley
Need to know the thread pitch and diameter for the water pump pulley bolts? The previous owner of the engine I bought clearly didn't know how to get the fan off as the pulley and plastic fan are both loose so I cannot loosen large nut.
View 1 Replies