Ford 6.0L Power Stroke Diesel :: Remote Mounted Oil Cooler Installation?
Mar 3, 2015
I am sure some of use around the forums have seen some of Diesel Tech Ron's videos, well in this video he is installing one of Bulletproof Diesel's remote Oil Coolers on a 6.0
Bulletproof Diesel's remote mounted oil cooler install on a 6.0 Powerstroke - YouTube
I like the idea of these if you ever have to do any work on the Oil cooler or replace it it would make it pretty quick and you don't have top spend a day tearing the engine apart
I haven't hear of too many people having issues with remote coolers set up's like this. Maybe there are some remote oil coloer owners that have em that can shed some light on how they have worked so far on their 6.0's ...
View 8 Replies
Advertisement
I'm getting pretty comfortable with these forums now. Not sure if this is in the right section, but even if it was, I'm not sure how to find the right one. I recently purchased Bullet Proof Diesel's Air-to-Oil oil cooler along with the BPD oil filtration. I've already drained the oil, but do I need to drain the coolant as well? I have read of people doing a complete flush before even installing a new oil cooler (OEM oil cooler). That way once it is installed, it doesn't have all the grit and sand pumping through it right off the bat. But does it matter with BPD's system? Should I go ahead and drain the coolant completely before beginning this job?
View 10 Replies
My buddy install a BPD air/oil oil cooler in his 2003 F250 last week and now there is coolant pouring out the tail pipe. I haven't seen it but he tells me there is quite a bit coming out. It wasn't doing this before we installed the BPD oil cooler. Normally I would say bad EGR cooler but his EGR is deleted. This is the 3rd BPD cooler I've put in and this is the first time I've had any issues after the install. The install went smooth other than we broke the radiator and had to install a new one. I feel bad cause I'm hoping it wasn't something I caused but I just can't think of anything I did during this install that would cause coolant to be getting into the exhaust. He just had it towed to the local Ford dealership.
View 3 Replies
2 1/2 years ago I installed a BPD remote oil cooler with BPD filter. The stock oil cooler was clogging up for the second time and didnt want to chance it. The BPD oil cooler works great. I have never seen high oil temps in any driving condition. Last week I was replacing the hubs and seals on the front of the excursion and noticed the oil was leaking from the 90 at the end of the hose oil filter location. I called BPD and sent them a picture. The 90 is corroded and is failing. They said something about a 2 year warranty but because of the rust they would not send one out for free. I purchased a new hose and the other 90 that goes right after it.
They recommended that I spray it with undercoating or something. I live in upstate NY and deal with a lot of salt on the roads in winter. I do keep the truck clean in winter as much a possible. I am posting this so if there are any others in similar situation you should do something to prevent that 90 from rusting like mine did. If I had known this when we installed it prob would not be replacing it now. Will be replacing it tonight or tomorrow. BPD said I will need a 1 1/4 crow foot or remove the turbo to get to the other end of the hose. Not posting this to bash on BPD just sharing so any others can prevent this part from rusting out.
View 14 Replies
I have a 04 that has 153k on it. 4" cat back exhaust with no cat. SCT tuner running a custom street tune. New FMIC with the extra tune on it. Head gaskets where done at 90k along with ARP studs. EGR cooler, The oil cooler was cleaned, New coolant tank. 1-new head and The cooling system was flushed at 90K. All done by the dealer along with some other items. Installed a bypass coolant filter at least 60k miles ago.
I have been having a no heat issue sometimes at idle this past winter and a mystery loss of coolant. I replaced the cap with a OEM one. I did a vacuum test on the coolant it held at 25 inches for well over a 1/2 hour. Pulled the egr valve it looked somewhat like tar inside not 100% dry. At startup it sometimes blows some white smoke and other times it's black smoke. I've had the scan gauge on for the last week to check my deltas.
Running 65mph the deltas stayed around 10 degrees diff.
Running 70mph the deltas stayed around 14-16 degrees diff.
Yesterday just running around rural roads 55mph and under the deltas stayed around 10 degrees diff.
I have not found a lower pressure gauge to do a coolant pressure test.
It does look as though it has burped the cap. Because of the deltas I'm thinking a plugged oil cooler my be the problem.
View 9 Replies
I changed my fuel filters a couple weeks ago. When I opened the hood the other day i noticed a kinda hissing or sucking sound coming from the engine mounted fuel filter. I've watched epics video a couple time and think his made the same sound but not sure. I am just paranoid with all the hpfp problems. It runs fine and had no long starts or hesitation at all. Lemme know if you all have the same thing. I just can't remember if it sounded like that before. I have done the air purge properly and several times since changing the filters. I notice the sound while doing the air purge procedure with engine off and key on.
View 3 Replies
I've been looking for a remote start system to install on my truck it has no remotes of any kind now. I've been googling most of the day and i can't seem to find anything except something that hooks to a edge tuner of some kind.
View 6 Replies
I am doing heads studs and gaskets on the truck. I forgot to remove the stand pipe and started to lift the head off the truck with the engine jack. Well i bent the stand pipe and the port to the bock was a little loose. Tightened it back down and it seems ok. Could I have damaged anything by doing that? how is that all connected to the high pressure oil pump? I just want to make sure i didnt damage anything by doing that and since im already here I would rather make a fix instead of needed to tear down again.
View 5 Replies
What is the consensus on this setup? Is it worth the money? Or is it more hype than function? Their logic behind it definitely seems to make sense.
View 11 Replies
Just found out that my EGR cooler is bad. How big of a job is this/how much down time if a compatent tech is doin the job?
View 14 Replies
I just replaced my oil cooler and 500miles later its clogged again. Delta reached 40F.. No fun... I replaced it with the factory ford cooler and installed the coolant filter but I guess when I did the first flush I missed sum gunk.
So my question to you PROs, should I reflush/restore again then replace the cooler? OR Go with one of these??
- Coolant-to-Liquid Oil Coolers
- IPR External Oil Cooler Kit for Ford 6.0 Powerstroke
The budget is tight, but I gotta keep the truck going.
View 2 Replies
I'm considering the BPD cooler MINUS the filter. Anything wrong staying with the original filter?
View 7 Replies
Well it looks like I'm going to have to put a new oil cooler on my truck. Does ford have an upgraded version or do they still offer the same cooler?
View 5 Replies
My 2011 has 62k miles and has been throwing P0401 codes, which results in losing power. I assume the EGR cooler is clogged. So I went to the dealership to see if it's covered, and was told there's no warranty coverage.
I would rather blockoff the EGR cooler than repair it. I would also like the extra performance from a tuner like the MiniMaxx. I do prefer the stock exhaust and not real excited about the drone/smell that comes with deleted DPF.
Will I have issues if it's tuned with the EGR blocked off, and stock exhaust? Or am I better off doing a full delete at this point?
View 14 Replies
Is there a way to fill up the reservoir for hpop and cooler after replacement? I didn't want to burn down the starter and kill batteries cranking all day until everything is full. I did the usual upgrades on the motor and about ready to try and get it started up. Where does the oil drain to when filter is removed?
View 3 Replies
My dad's 03 has had some work done after his oil cooler was clogging. New oil cooler, egr delete, head studs etc. The oil temp seemed to run some what high when he got it back. After a couple interstate runs on cold days 15-20 degrees, the water ran around 185 and oil as high as 218 but usually a bit lower. What's going on here? how could this thing be clogged again? It hasn't seem to gotten much worse since we got it back but not better either.
View 8 Replies
Got everything done today. So I thought. Went for a drive. turbo not building boost. I checked the map hose and barb. Clean. Checked connection at ebp and vct, both plugged in. No exhaust leaks. turbo shafts feels good and spins good. made boost fine before repairs. 2006 6.0 f250 .....
View 14 Replies
2004 6.0 90k miles... Oil cooler plugged & coolant puking due to egr cooler flash boil.
Flushed the coolant with tap water then replaced water pump and tstat weekend before. This week backflushed heater core & block. This weekend backflushed the oil cooler. My coolant system would be considered severe contamination due to tap water use resulting in rust. Average ect was 195-205 & avg eot was 230-240 before flush. Here's a baseline before flush.
Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac. The pressure was pretty intense holding the hose into the bore just running water through it. Hit the trigger about 20 cycles of water then air blasts.
Filled with 1/2 gal of restore & tap water. Ran it for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Then dumped restore while hot, was pretty cloudy but not that dirty. Let engine cool then filled with tap water, ran for 10 mins then dumped again. Stuck hose in degas with only the the drivers block plug pulled & revved engine a few times to have the water pump push any crap out. Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac again. This time the back pressure on oil cooler was much less vs first time.
Took a mason jar with restore plus in it & boiled it in water. Got it up to 190 then poured it directly into the oil cooler & let it sit for 30 minutes. Then backflushed again.
Put rest of the whole gallon of restore plus in & topped off with tap water. Ran again for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Dumped restore plus while hot & it was very green & contaminated with rust. Topped off with tap water, ran for 10 mins at 190 then dumped. Revved the engine again with hose in the degas bottle & only drivers block plug out to blow more junk out. Filled with tap water & dumped again.
It was late last night so I filled it with distilled & parked it. Plan to do 3 straight distilled water flushes this week running rpm 1k+ for 1 hour each time in hopes to rid all the chemicals.
The backflush didn't result in lower deltas, but it didn't puke from the degas bottle at all during both chemical flushes. The oil cooler definitely needs replaced but at least it's not puking anymore & will hopefully stay this way for about 1k miles of driving so I can let the coolant filter rid anything that breaks loose during driving. My hope was to get some sort of flow across the egr cooler to stop the flash boiling puking & get as much junk out of the system as possible. So I guess there's some sort of achievement in the end.
Currently running cheap regular green (mixes with all) elc. I am running the cheap stuff because when the coolant was puking a gallon of coolant every trip i couldn't justify upgrading to the Rotella ELC yet. Plan is to flush with rest of restore(1/2 gallon) after oil cooler r&r then switch to Rotella ELC.
View 14 Replies
I thought I remember a posting about removing the radiator to do the cooler because it made it easier to work standing in the engine bay with the engine in front of you instead of leaning over and removing everything from outside ? I'm getting ready to do my 4th external oil cooler? And is it difficult to remove radiator, and/or worth removing it ?
View 14 Replies
]I am in the process of swapping my oil cooler. When i pulled the smaller cover off of the cover that goes over the oil cooler, i heard a pop. The cover, not the one that bolts onto the motor the one that bolts to that, is cracked...bad. is there a place i can get one? need to know parts illustration with numbers?
View 14 Replies
My orange one leaks, bought a blue one. How the heck to I install it? I have decent tools.
I reviewed the threads on coolant flush and fill, and bought a coolant filter kit, I will be doing that at the same time.
View 14 Replies
