OK here's the deal. Cruising down the road at 55 mph, I felt a pop and then the engine just stopped running.
When I tried to start it up, no oil pressure. It appears that the IPR valve may have failed, but I'm curious if the pop was a catastrophic IPR failure or an indication of something else?
Driving home from work last night my truck just died. I was under load, going up hill, and she just shut down. No power, completely dead.
She'll crank, but not start.
Ever hear of this?
luckily about 5 minutes from home my trailer running lights AND the lights on my dump truck body stopped working. i assume they hooked the lights to my dump body to the trailer lights. i was towing an old trailer that has electrical issues so I'm sure that caused it. Under the hood there is a 30 amp fuse #26 that i think is the culprit. (All the other similar fuses are shiny and that one is kinda black). I've never bought fuses like this before, what type is it? it's a big square one. Are they available at auto zone? Does the whole thing pull out and do you need a special tool for it?
View 3 RepliesMy uncle bought an '05 that stopped running one day. He was driving down the road and engine lost power. He was able to coast into his driveway. Unfortunately, it's been 10 years since I've work on a 6.0 and no longer have any of my computers.
He did state there is no check engine light. He's going to change the filters today / tomorrow. I'm hoping to make it down there this weekend to look at it, but what to look for. Even more unfortunately, we really don't have any specialty tools or gauges.
I've got a 2012 F250 SD and when i go over some bumps in the road or even down a gravel road, the door panel on the driver side vibrates and it's noisy. Is there any way to pull the panel and add some foam padding or something to stop this? I can see the panel vibrate or heck, maybe it the whole door.
View 10 RepliesWhile stopped, engine running, in D, the engine cut off just like I turned the key off. I sat there for about thirty minutes and on the 7th or 8th try, the engine finally started. I drove it back to camp and thinking it might be the CPS, I swapped it out. Unfortunately it must be something else because I can't get it started anymore.
ICP and IPR are fairly new, but I unplugged the ICP and tried to start it anyway. It didn't choke out (like it was a fuel issue) but I checked the fuel bowl anyway and the pressure builds fine. I got it restarted once, so it can't be a fuse but I checked them all anyway.
Oil pressure builds to 780+ when cranking. Batteries still have plenty of cranking juice and without my AE, I'm frustrated beyond belief.
I was driving from my house the other day when the engine suddenly cut out and the dash went blank. there was no warning, it was like someone pulled the plug.
-When I turn the key to the first position (Acc) all the accessories work as normal. the lights, radio, windows, ect all work like normal.
-When I turn the key to the second position (run) nothing changes. no gauges, no dash lights, warning lights, and no (wait to start) squiggly line. only thing I hear is the high pressure pump on the engine cycle.
In the third position (start) the truck will turn over but will not start.
I am having a problem with a 6.7. The truck has 9900 miles on it. It has a dpf delete, egr delete, Spartan tuner and a snow stage 3 kit. The truck lopes at idle but once throttle is applied it levels out but still runs a little rough. Its keeps saying its in reduce engine power no matter how many times I clear the code. If I clear the code it will come back in 2 seconds with out cranking the truck or anything. Rail pressure is telling me 31090 psi and not changing running or not. I have changed rail pressure sensor, and pressure control valve with no result. The green and violet 5 volt reference that feeds those sensors is only putting out 1.2 volts. Put a new pcm in it still the same and now has quit running totally. The codes are P0193, P0335,and P06A6.
View 14 RepliesEarly build 6.0 (2003) starts fine in CT winter weather as long as its plugged in, HOWEVER, will not start after engine has been running! It just started doing this a week or so ago and after plowing all day yesterday, it just wont start after the engine is up to operating temp. It will start on a shot of ether but I only did that once to get it home.... Other than that, the truck runs great! I changed the oil today, checked the ficm (48V) and the injectors were all done less than a year ago. The only code I get every once in a while is Cyl 1 injector circuit low and that goes away on its own. I'm not really sure where to start.....
View 4 RepliesI've been getting a surge or revs when getting up to cruising speed before it drops into overdrive or or a constant speed. Happens around 1800-2200 rpm before up shifting to the next gear. More noticeable if under a load or going up a grade when it will hold gear longer before shifting. Only thing I can think of that would be related is the truck does lack some power on a cold start for the first couple miles before getting up to temp. I've cleaned the ebp sensor and it appears to be working correctly, reading within .1-.2 of BAR/MAP key one engine off. VGT solenoid is clean but have no real way to tell if it's working correctly. Other values icp/ipr temps fluid levels appear to be correct. Just changed the oil and it continues, changed the transmission oil and filter about 3000 miles ago. I've had this going on for about 1000. Started about the same time I changed tunes to PHP. They haven't been able to find anything in the tuning yet that could be causing this or if it is just making it show up now.
View 14 RepliesStill chasing a surge for some time while cold, mainly. While hot and cruising 65 mph the turbo still surges faintly.. but today was a different story, very fast and high surging from the turbo only, while on overdrive as usual. It calmed down as i dropped the boost a bit but it was quick swings of about 3-5 psi which is quite bad for what it had been doing which was manageable.
Short of taking off the turbo, I took out the VGT solenoid and it had some oil burnt on the end, cleaned that up and pushed the plunger in all the way a few times and it 'seemed' to have worked greatly, until today.
I pulled some other numbers;
KOEO
Map 13.7
EBP 14.1
Baro 28.2
Cold Idle
Map 14.0
EBP 16.5
Baro 28.2
When cold, mainly below 130F the RPM gauge itself will surge or hesitate around 1700-2000 RPM. Any higher or lower it will be smoother I suppose....
I looked but can't find it again. I have mini h&s and was wondering when wanting to do live data inspection with engine running can you just unplug tuner and still run the engine or does it not work? If I remember right I've read and seen that someone can still drive and use truck with it unplugged just isn't at full power?
View 14 RepliesI get what I can only describe as a "missing" when Im on the interstate just cruising along with rpms below say around 1900. That seems to be when I have noticed it. It is not very frequent but often enough to not let me forget about it. Happens when I'm towing it seems more than when not. Seems the rpms have to be below 18-1900 and in 5th speed. You can just feel the truck ever so slightly missing like in the old days of points and distributor caps. No tunes
View 7 RepliesJust a quick question but is it normal for the ICP voltage (ICV) to jump around a lot at idle or while cruising or accelerating? Started watching this pid and not sure what's normal and what's not.
View 13 RepliesOk this may be the norm, but I'm hearing something like a motor running after i kill my engine? It sounds like a fuel pump or something!!! O ya I have a 2011 6.7. I've had the truck for several months but just now hearing this....
View 11 Replies,the symptom that I'm wondering about is that when the truck is cruising at different high speeds like 65 or 75 it starts to jerk/jolt, if I accelerate it goes away, or if I let off the accelerator.
Once I settle on a different cruising speed it does it again. There is no smoke out the exhaust pipe, it does not loses any power, I look at the RPM's and they don't move when the jerking/jolting starts. Truck runs fine except for this issue.
I do get the P0404 and P0405 codes which are for the EGR valve and the sensor. By the way **is there an EGR SENSOR** anywhere on this engine, I seen some posts where people refer to it as the EBP Sensor, is this correct? I cleaned the EGR valve, but it did not do anything to fix the issue. I'm thinking I damaged the valve when I cleaned it, but I would like to verify that this symptom could be the EGR valve before I buy a new one.
I have a coolant leak somewhere on the top of the engine running down to the oil pan and bell housing. I have done some research and discovered it could be the coolant inlet tube to the turbo.
View 14 RepliesI recently purchased my 2011 F250 Powerstroke a week ago today with 87000 miles on it. the dealer assured me they did all the maintenance on the truck before i was able to drive it home. I noticed on my dash that it kept popping up i needed to change oil soon.. so i got out to investigate and realized i was about a quart low on oil so i looked around more and am seeing that i have a leak coming from the back of the engine running down to the oil pan.. I have not noticed any on on the ground at all but what this leak is coming from...
View 14 RepliesI have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 Replies2003 F350 6.0 with 290k+ ... It has a skip in the engine at idle and running. At times when running down the road skip seems to get worse. Changed both fuel filters, didn't work. Truck start up is normal, no leaks, and flashing no codes.
View 3 RepliesWell it finally happened, a couple of weeks ago I was headed to an MX race and my check engine light came on and it started running rough. Long story short a piece of an exhaust valve broke off and went out through the head. Dealer has been great even though I was 300 miles from home and they did get me a rental(small POS SUV). Truck was supposed to be finished this week, but now they are saying the head gasket is on back order and they probably won't have one until the middle of April......... I can't be without my truck that long, but not much I can do. By the way truck is completely stock with just under 20K on it, and I have never had any issues with any of my Ford trucks or Ford diesels, even my old 6.0.
View 7 Replies