Noticed a problem on the way to work my passenger headlight doesn't work when they are on automatic but do work when I turn them on manually with the switch
View 9 RepliesMy dads truck is an 04 and we have went through this before. We replaced the whole head light switch and they still didnt work. All the sudden one day they started working again. They have worked recently until now. Same condition as before, the fog lights work, parking lights work and when you pull the lever back for high beams they come on as well but no headlights. Looking for a diagram to track this down.
View 7 RepliesI just happened to look out the window of the house and see that the headlights on my truck were on. However, they were turned off from inside. When I stepped on to the porch, I immediately smelled something electric smoking. I tried turning off the lights by switching the lights from on to off, but that didn't effect the lights at all. There was a humming close to the turbo and the smoke seemed to be in the cabin more so than under the hood. I've had this truck for most of its life and it's never had an electrical issue. What it could be?
View 8 RepliesMy headlights are blinding other motorist an I can't figure out how to adjust them...
View 6 RepliesWell a few days ago I pulled up to a gas station on my way to work for some coffee and since I leave for work before 6:30 AM my headlights were on. Well only the running lights were working. Well I shrug it off and later that night I come to the realization that both headlights weren't working. I tried the high beams and they do work. I also pulled both bulbs and both the filaments on each bulb seemed to be intact. What could cause this? I checked fuses 9 and 11 under the hood and they were both fine. I'm kinda at a loss right now.
View 9 RepliesWanted to replace my front headlights on the '06 with the PIAA Extreme White bulbs.
Before I ordered them I looked to see how easy the bulbs were to access...
Looks like its a bear to access. Is there a video??
As a side note I already have the Brite Box installed, which I really like
How do you remove the front grill? I'm changing the bulbs in my headlights, and I know it's stupidly simple just can't remember how to do it.
View 1 RepliesJust bought a 03 F-350 dually today. 6L 4x4.
Headlights don't work , everything else does? Dash lights , taillights , cab marker lights all work. Headlights and front park lights don't?
I also see the overhead console is dead and shows nothing? Plus the ignition turns without a key being in it?
It blows, but only lukewarm..... feels like it's out of or low on freon, but I won't know until tomorrow. Searched the forum but I appear to to be the first with this issue? I just hope it's covered under warranty, whatever it is.
View 14 RepliesCan you replace the passenger side up pipe without pulling the turbo, etc? My bellows blew out. Y-pipe is still ok. I've already deleted the EGR, so what's the best to put back? Go back to the original style or just put in a straight pipe? Where to get one?
View 2 RepliesDefrost not working. Looking for the vacuum pump so I can troubleshoot it. Where to find it in the engine bay and trouble shooting it other than listening to whether it's on or not when engaging 4x4?
View 14 RepliesI can't seem to get my fog lights to work. i checked am both bulbs are good. I did pull out the headlight switch. I checked fuse 43 an its good. I popped dash out an checked wires to headlight switch an found the wire for the fog lights, yellow wire on my 05.
Its getting power when I pull the headlight switch out to turn on fog lights. Pulled plugs of of fog lights an getting no power to them.
They use to work. i put in some HID headlights an they still worked. then i put some led's in my instrument cluster an sometimes they would work an sometimes not. now they wont come on at all.
I went on a 4oo mile trip the other day and kiddos were in the back playing games and powered up- Next thing I know the AC seems to not be working. It was pretty cool outside so I tested it a little and I could not feel any cool air in the seats and teh vents were not very cold.
Clutch seems to be engaged and not cycling.
I am taking back to them Wednesday.
I know jack about tie rods. But what I do know is the passenger lower-outer tie rod is clunky [Right where it connects near the wheel. Jacked up the truck and moved the tire from right to left and the passenger side lower tie rod made a very obvious clunking noise right where it connects with the upper piece.
My question is, can I just replace the passenger lower arm or do I need to replace the upper [not sure what it's called] that it connects into? While under the truck I found it difficult to figure out exactly how they are joined together and taken apart? My drivers side is nice and tight, no clunking.
2005 F-250 CREW CAB 4X4
Coolant seen leaking under passenger door it was running down frame rail looked under hood and seen coolant around the air filter cover . Tank was low 2012 cab chassis 33,000 miles
View 4 RepliesI just see a fluid by the front passenger tire leak when the diesel is running and ac is on.There was fluid up by both aluminum lines going into a plastic canister in the engine compartment on the passenger side.I couldn't find any cracks in the hoses or aluminum lines..The plastic canister I believe is (AC ACCUMULATOR ) did have a hiss of air when I shut the truck off. I can't see where the clear liquid is coming from. Just started to leak by the front passenger tire.
View 3 RepliesI discovered my passenger side carpet was a little damp not bad but was wet. I hosed down the window, windshield, door, and the sunroof areas and didn't see any water coming in!? The only thing I've noticed, when running the AC it seems to have "more" water coming down the frame area but not totally sure but sure seems like a lot more than I remember! Just wondering if, when driving down the road, that the water from the AC is coming in somehow?? Again, the carpet isn't completely soaked but damp, even up under the glove box area on the carpet. Heater core?
2006 F350 4x4 CC KR with 138K completely stock!
I have to change out the inner seals on my front axle on my 04 f250 6.0 4x4. was wondering what the torch spects are for the bolts on the end caps and the torch spects on the differential cover? I already have the passenger side axle out. was changing my ball joints on that side when I noticed a bunch of oil in the axle case and on the hub knuckle. Also, this might be a long shot but is there any way to change the inner seal on the drivers side without taking out the axle on that side? I have the passenger out and if I could get away without pulling the driver side that would be awesome.
View 10 RepliesMy truck does mostly pavement duty so no telling how long ago 4WD quit working but I needed it the other day and it's now a no-go. It's the '06 truck in my sig and it has ESOF.
When I flip the switch (4hi or 4low acts the same) my A/C continues to come out of the dash vents, it doesn't change. With KOEO I can hear a whirr-click from under the truck when switching 4wd on and off, I get noise both ways. 4x4 light on the dash seem to work correctly.
Broke out FORScan and got the following info:
===GEM DTC P1832===
Code: P1832 - Transmission Transfer Case 4WD Solenoid circuit failure
Module: Generic Electronic Module
Diagnostic Trouble Code details
Transmission Transfer Case 4WD Solenoid circuit failure
===END GEM DTC P1832===
[Code] ....
Any tips to quickly nail it down between the switch, GEM, wiring or solenoid? Looks like the whole thing is failing. I've climbed under the truck and all the wiring appears undisturbed. No recent work under there. In FORScan, these DTC's were generated in a user initiated test and I didn't pick up the instruction to re-run the test in 4x2 mode until I posted just now.
Under the hood everything seems to be routed correctly and connected. Vacuum pump runs a short while on start up like always has. I can lock hubs manually and they don't seem to be binding hard but they are a little stiff, haven't done that before so I don't know how hard it should be to turn them. I have a MiteVac but haven't tried using it to try and lock the hubs. Not sure any of that matters (yet) with the DTC's listed above.
Do the gauge cluster out of one super Duty will work in another truck, just plug and play? I have a 2015 550 that the fuel gauge has quit, which is causing the truck to go into limp mode because it will not allow a regen on the DPF. This is a business truck and i need it to be rolling. There appears to be a national back order on gauge clusters from Ford. I have another truck in the fleet that I could do without so I was wondering if I could just swap the clusters would it work?
View 6 RepliesI currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 Replies