Ford 6.0L Power Stroke Diesel :: P0275 Code For Cylinder 5 Contribution
Jun 15, 2016
I have a 2004 F250 with a powerstroke 6.0. I have done the egt delete and oil cooler upgrade. Last weekend I did head gaskets, arp studs, new heads, injector o rings, updated stand pipes and dummy plugs, glow plugs, glow plug harnesses, water pump, and exhaust gaskets. After everything was done and truck was primed and started it ran really rough. I drove it a little to possibly purge any air and it still ran rough and I got a code p0275 for cylinder 5 contribution. I removed valve cover and oil rail and swapped injector 3 and 5. 5 was covered in fuel. After reinstalling oil rail I cranked engine over and saw cylinder 5 intake valves were not moving. Removed rail and rockers. Pulled push rod and it was bent. Installed new push rod a and reassembled. Crank engine over to verify all rockers were moving. Reinstalled valve cover and started truck. Truck ran great. Cleared codes and test drove. After test drive truck sounded like it was missing so I checked the codes again and p0275 was back! I know at this point I need to check the harness but any other possibilies you may know of? FICM voltage it good at 48v and oil pressure reads good as well.
View 7 Replies
Advertisement
I have an 04 f350 with an 03 6.0 motor. Truck started running very rough a two weeks ago. Checked codes and found p0274 and p0275. Both codes are for cylinder 5. I replaced #5 injector and truck ran like normal for a few days then began to miss again when operating temperature hits about 187+. It will show code p0275 once hot as it misses. When cold runs fine, starts fine. No smoke. Could I have put In a bad injector? It was purchased from AutoZone...
View 14 Replies
2003 f350 dually. Fully bulletproofed about 10k miles ago. Everything was running great for about 5k miles. A friend of mine got stuck and I went to pull him out. Got him out but got on it really hard...never overheated or anything.
Next day truck throws a cyLinder 5 contribution balance code. Ran ok but idled rough. Pulled injector and put a used one from a running truck in it. Code went away and runing fine for a few weeks. Took a long trip from FL to Texas, and on the way home same code occurred but idle was not as bad. I would clear the code and it would be fine for a few hundred miles, then would show up again. Made it home, still was driving around town a little with the code only showing sometimes. A couple blocks away from home taking off from a stop sign lost all power and motor shut off. Turned out the Injector o ring blew and hydrolocked the motor.
So now, ordered all new 155cc30% injectors , 58v ficm and new oem injector harness. Installed and Drove the truck to Illinois. After about 700 miles I noticed a little rough idle and had a cylinder 4 cont code. Made to Illinois and back to fl. At fl line I had cyld. 4 and 5 codes now. Cleared and cyld 4 was gone but 5 stayed. Got home and balance test showed 4 and 5 bad injectors. Sent them off to be fixed just got them back in. Truck started fine, smooth idle, ran for about 10 miles and cyld 5 code come back and so does the rough idle. I'm at a loss now.
Will be doing compression test tomorrow. Other than a rough idle truck runs flawless, will roast the tires and pull anything hooked to it. No hot starts, no symptoms of anything else. Possibly a problem with the oil rail feed on that cylinder? Main ficm harness? Bent pushrod?
View 7 Replies
I have an 03 ex with 03 motor. I use torque pro all the time and periodically check for any codes. Well, I got P0278 but no check engine light. It does seem to start a little different than our 05 with 04 motor. It sounds like it just doesn't fire right away or like it turns over and then decides to start. It doesn't make the destinctive sound at the end of cranking when it starts. I hope that makes since. I could tell it sounded different, that is why I checked for any codes. It also seems to run just fine down the road and at idle. Where to start or what to look for?
View 14 Replies
I have a code for #6 low contribution and a thumping noise out the exhaust. When I turn number 6 injector off the popping/ thumping goes away. Truck is straight piped and deleted. It started doing this after getting on it hard to get on the high way. Sounds like beating an empty pop bottle on something
View 14 Replies
#2 contribution/glow plug/injector code ????? Harness looks good. What's the malfunction?? Runs rough. Never seen those 3 codes together.
View 2 Replies
My truck is currently stock and recently started making a knocking noise louder than it usually does. I researched and have found the injectors can make a knocking noise when not performing correctly. I took it to a local shop who hooked it up to a snap on scan tool and ran some tests. It passed the Buzz test but continually failed the contribution test on cylinder 8. I'm going to go home and remove valve cover and unclip the injector to see if the noise goes away. I'm sure hoping it does as an injector by the looks of things is definitely the cheaper option. I'm scared because if I was listening to a gas powered truck and heard the sound my trucks making I would assume it was a lower end noise. My truck only has 148,000 miles....
View 14 Replies
Pulled p0678, glow plug 8. I've changed out the glow plug on cylinder 1 a few years ago.
Cylinder 8, being on the driver side rear, is it difficult to change out? Should I just pay Ford or another shop to fix this?
View 6 Replies
Truck all of the sudden out of no where started to shake at idle my first thought was that it is a miss. Then on hard acceleration blows black smoke with NO tune on at the time, plugged reader in and got code P0278 cylinder 6 contribution/balance. I'm assuming it is a dirty nozzle on the injector. Shake/miss clears out at about 900-1000 rpm. Truck as 247k on it. 50k on injectors. Has ported and o ringed heads, studded, and fully deleted, with bullet proof ficm. Would my assumption be correct?
View 6 Replies
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
View 7 Replies
Have a 2004 F350 which had problems starting cold and once started had bad throttle response until warm. It also had a shudder at cruising speed when going up a slight incline, would shudder until turbo kicked in.
Pulled codes which related to FICM and codes for all 8 injectors. 7 injector codes were circuit low, cylinder 1 high. Tested FICM voltage and sent FICM out for repair.
Installed rebuilt FICM, cleared codes, and hard start went away, but cruising shudder is still present.
Only existing code is P0262 for cylinder 1 injector circuit high. I'm assuming that cylinder 1 injector is bad -- are there any tests to confirm before I take it apart to replace it?
View 7 Replies
I have for a week suspected my batteries were getting weak. just slower cranking is all. I took my truck in to have a viper security system installed and while he was doing his work he killed the batteries. I saw him hook up a battery charger and started the truck. He pulled it around to me and explained how the system worked and off i went. 5 miles down the road, on the thruway, I notice a miss and I'm down on power. FICM looked ok, 48V and it was charging, 13.8 I thought I would bring it to my shop and load test the batteries. On my way here, the check engine light comes on. At the shop, load tested them and they were weak. Installed 2 brand new batteries, started it up, no difference. Hooked up the scanner and pulled a code P2077 (cylinder 6 injector circuit high) Now what? I'm not sure where to go from here. I'm guessing either the FICM went bad or the #6 injector?
View 12 Replies
I know this is a common code and a common problem. I have had a buzz test and glow plug test done, no codes. Scanner code came up with P0275. I have read about injector change out, to O ring failure, to new EGR style. I have a 05, 6.0 SD SRW auto.
View 1 Replies
My 2011 6.7 suddenly lost power, started making noise and then stalled out.
After finding out that there are zero 24 hour service companies available in the LA area, I was able to get it towed to the local Ford dealer.the next day they told me it had dropped the #5 cylinder and that they would have to tear into it to find out what happened.
While I realize that any thoughts on the situation would be primarily idle speculation, what would cause this to happen at only 125,000 miles.
View 14 Replies
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
View 14 Replies
2007 F350... I noticed I have a small power steering leak where the master cylinder bolts onto the hydroboost. Is there a o-ring or seal between the two? or do I have to replace the hydroboost? Been looking online for a schematic but can't seem to find one.
View 13 Replies
I have a 06 f250 with 135k that I keep getting a #2 contribution code. Power balance shows cylinder 2 low as well. No circuit codes and everything sounds good on a buzz test. Valvetrain is actuating as expected. I changed all 8 injectors w/ motorcraft with no luck. I get over 300 psi on a compression test ( 175 psi on 1st stroke then maxed my gauge on the 2nd). It smokes until I disable cylinder 2 then it pretty much clears up. I did notice I could move the top of the valve stems about 1/16", this seems really sloppy. Very little blow by and the oil cap stays on up side down until it rattles off. Any other 8 deal other than pulling the heads? I just bought this truck and have little history on it.
View 12 Replies
I bought an 06 6.0 f 350 4x4 dump bed cheap. seller said it was sitting for 1-2 years and wouldn't start. ficm is at 48 volts fuel pressure is at 100 oil pressure builds fine, then checked compression and reading no compression in any cylinder. My mechanic says new motor or possibly both head gaskets are blown.
View 14 Replies
Truck has been running very well while in the warmer North Carolina climate pulling trailers with no limp mode or wrench light. However, when daughter started the truck this morning, SGII showed one DTC and when she pulled it up it was P0675. OK, glow plug num 5 maybe or the module. No issues starting or rough cold idle. I told her to clear the code and we'll see if comes back.
She did ask if it is something she should have it repaired before the trip back to Vermont. So I thought I'd ping the group here since reading posts, they seem to be fairly easy to replace (and assuming it isn't a chafed wire) and I could probably save her some $. Just want to make sure there isn't any chance of real engine damage.
View 4 Replies
I have an 03 X with 225k on it. I put 8 new injectors in it because I was leaking fuel into the engine oil. I got them from dieselogic from ebay in Jacksonville FL. 4 of those were leaking and they warrantied them. Then 2 of them were getting contribution codes and they would not warranty them because they said I had fuel contamination. They did not send them back to me either. I got 2 more from advance auto parts. They were working fine. For a little while. So now here is where the problem is. I was getting a cylinder 1 contribution code. So I swapped cylinder 1 and cylinder 3 injectors. That code is gone now.
Now I have cylinder 4 contribution code. I swapped 4 and 6. Still have cylinder 4 code. When the engine is cold it runs perfect. When I drive it for about a mile or so and come to a stop sign it's still running perfectly. While I'm at the stop sign it's like someone flipping a switch and then the misfiring starts. And no codes until the "switch" is flipped. Ficm measures 48 to 48.5 at all times. I don't see any chafing of wires. And I forgot to mention that I had a leaking fuel into the oil again. Ran another dye test but did not see any signs of leaks this time. But that was after I swapped injectors around. Could have been leaking from the orings. I can't can't figure out this misfire. So I was thinking compression test next but why does it run fine when cold?
View 1 Replies
So I got an IDM code and then after running AE buzz test got a P1273 (#3 cylinder high low open).
Ohm'd out the 42 Pin - got 3 across the board. Only test 42 pin from valve cover to injectors.
Double checked UVHC
Swapped solenionds
Swapped injectors
Did ford wiggle test.
Ran Injector buzz between all those steps and still get P1273.
What's the next step? Ohm from IDM to 42pin? May actually be a bad IDM?
View 10 Replies
