Ford 6.0L Power Stroke Diesel :: Oil Pressure Gauge Showing No Pressure
Dec 30, 2015
Last week I was driving on the highway and noticed the oil pressure gauge showed no pressure. Limped a half mile to the mother-in-laws and called for a tow. As my truck was pulled onto the flatbed I could see oil all over the bottom of the engine, tranny, rear end, etc. Turned out to be a bad oil pressure sender, which was leaking enough oil to blow the plug off the top of it.
I replaced the sensor, cleaned the engine and under-carriage, checked oil level (which showed no loss of oil) and drove around for a week without an oil pressure gauge while I waited for a new pigtail. Put the pigtail in yesterday and drove it today for the first time since. Gauge was working, got to the bank and it was reading zero pressure again. Limped home and watched the gauge go back up quickly and then back down. This happened twice and was showing pressure when I shut it off. Checked under hood, no oil leaks and plug is still secure.
View 9 Replies
Advertisement
The tire pressure warning light has been on in my car for about a week. The dashboard computer says that the tire pressure in the front right tire is 17 psi, but when I use the pressure gauge, the reading is almost 40 psi. Is this something I should be concerned about? What could be causing this problem?
View 16 Replies
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 Replies
I currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 Replies
Have 2006 Ford Power stroke with 6.0 in it.. Just started doing this ... When Im driving the oil pressure gauge is fine and motor sound fine, but sometime when I come to a stop sign the oil gauge will drop all the way down to zero, the motor still runs fine and has plenty of oil in it. After I press on the fuel pedal to raise the RPMS just a couple the gauge goes back up. the odometer will all so blank out and it will flash "read gauges" when this occurs,, its driving me crazy and not sure where to start..
View 14 Replies
Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 Replies
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
View 11 Replies
I finally received all the parts needed for installing my fuel pressure gauge, but I am wondering if I am going to need a schrader valve on my fuel pressure line going to the sending unit, or if I am going to be safe with just doing a 6 time cycle of the fuel pump like we do when we change out the fuel filters. Seems like that should work for getting the air out of the fuel lines, same concept I would think.
View 14 Replies
Well, I was cruising down the highway @70MPH and notice the fuel pressure gauge dropped down to 50 then back to 65. Kept watching the gauge and it would swing back and forth from 55 to 65.
Got off the highway. Nailed it at the light and watched the gauge drop to 53 and swing back to 65. Fuel pressure is not steady either. It swings back and forth from 52 to 65. Thinking the pump is on its her last legs? Truck got 194K on her.
View 5 Replies
Couple of years ago I installed a fuel pressure gauge. I wrapped the fittings with teflon tape. Well within about a year it started leaking. So I shopped around and used Permatex Permashield fuel resistant sealant on the fittings. It says diesel resistant on the package. Couple months later leaking again. So I take it apart again, clean every fitting and follow the instructions to the letter. Well its leaking again. What will resist diesel fuel under 55 psi pressure. All the fittings seem to be pipe thread.
View 7 Replies
I had new nitto snows put on my truck and low tire pressure light is on.....Checked tire pressure 65 front and 80 back.....Started truck and screen said tms pressure low.....Hit ok and drove around on and off for 2 days now and cant get the light to go out......Is there some way to get the light out or do I have to go to my dealer to have it reset???
View 14 Replies
OK so 2006 f550 6.0
If I want to monitor fuel pressure with a gauge in cab while running all the time... (not just testing) can I purchase one of the secondary fuel filter caps that have a port in the top and connect the sensor to this to run or is there a better way? (Or is that not going to work)
Cap I am talking about is something like this
[URL]
(I know this is a combo kit but they do sell the fuel only) But since it has a threaded port in the top I could connect the fuel pressure sensor to that and go from there correct? Would that give accurate readings?
View 4 Replies
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 Replies
My truck gave me low fuel pressure and reduced pressure limp mode at 21,000 miles. The fuel and air filters were changed at 16,000. The dealer said all they found was the fuel filters (at 21,000) were what needed to be changed. Also, why does my truck hum??
View 14 Replies
The backlight for my fuel level and oil pressure dash gauges are out. Would that require a simple bulb replacement or if there is something more difficult to replace, i.e. entire panel? The red needles illuminate, it's just the gauges themselves that are dark. The truck is my 05 Super Duty in the siggy.
View 3 Replies
After having my oil changed at a local place, the oil pressure gauge showed "high." hoping it would go away, i drove for a week. it didn't... took it back to the shop and they said it was a little full which would cause it to show high pressure. That was earlier today. The gauge however has not changed. Still shows high oil pressure. I need to drive 400 miles tomorrow and am not sure if it is safe? Perhaps just a bad sensor??? I need to know if i can hit the road or not.
View 5 Replies
The installation of the new 50 gal. Titan tank went well overall. Start up was smooth with no leaks but the fuel gauge is showing empty with about 45 gallons in the tank.
The sending unit was properly oriented ("clocked") so I'm guessing the electrical connector is not secure at the top of the sending unit. Not sure I can reach the connector without lowering the tank somewhat.
View 6 Replies
For the second time in 6 weeks My 2004 F250 Powerstroke has run out of fuel with the gauge showing a 1/4 tank. First time it was just under a 1/4 showing I had it towed to dealer and they told me it had sucked in the filters requiring replace and flush of system. The told me that this happening very often and I would be replacing all of the injectors at my cost. I told them that I didn't want this to happen again and to check out the fuel gauge and sending unit and replace if in doubt. Well they checked it out and found nothing wrong, told me it was accurate and should not be an issue again. Now 6 weeks later on the Friday night before a holiday, it did it again, this time with over a 1/4 tank showing. I really don't want to spend 6 grand replacing injectors and would really like to trust my truck again, getting to the point that I'm nervous at 1/2 tank.
View 9 Replies
I have a 1999 Jeep Cherokee Sport with 140K + and recently had an oil change. I went on a 8 hr road trip split up between 2 days (there and back). On the way home I noticed my oil pressure gauge acting funny, going up and down but not past 40. Today, I drove home from work (10 miles or so) and the check engine light came on and the oil pressure gauge was very low, almost 0. I made it home but was very nervous and noticed both today and this weekend there was smell, burning or burned type smell. What should I do? I don't really trust the garage that changed the oil and was skeptical taking it there but was in a pinch.
View 12 Replies
I need to install an oil pressure sensor sending unit. I've already occupied the 1/8"NPT test port on the rear of the oil cooler, where else might I be able to tap into oil pressure? (LPOP)
View 4 Replies
I bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
View 8 Replies
