Ford 6.0L Power Stroke Diesel :: Oil Temp Running High
Jun 28, 2015
I recently noticed on my truck that my oil temp was running high, I would go down the interstate at 75 mph and the oil temp would get up to 215-218 while my coolant temp would sit around 192-196. So, I took it into the shop and was told it was most likely a bad oil cooler and had it replaced 2 years ago when I had my injectors and gaskets replaced along with my egr deleted. So, got the truck yesterday, going 60mph down the highway, truck ran an oil temp of 192 and the coolant at 188. Was great, but later on once I got to the interstate going my 75 mph, The oil temp jumped to 209 and my coolant sat at 192. Not sure what the deal is, was told the oil cooler was replaced and wanted some input on what else I could be looking at. I currently have 5w40 synthetic oil running in it. I have an EDGE CTS tuner on it and tuned it back to stock mode, but oil temp still jumps up to 209 and coolant remains around 190-192.
View 14 Replies
Advertisement
I know they're supposed to be within 15 deg of each other. How bad is this? Pulling a small trailer with a polaris rzr on it. Running 75mph
View 14 Replies
So the other day while towing my 5er my temp alarm on my CTS went off at 220. I let off and it cooled down, but not where it usually runs. Unloaded it will run at 200 where it usually runs at 180 or less. Its an 06 EGR deleted, coolant filter, studs, the works. Water pump? Thermostat? Coolant level is ok.
View 14 Replies
My dad's 03 has had some work done after his oil cooler was clogging. New oil cooler, egr delete, head studs etc. The oil temp seemed to run some what high when he got it back. After a couple interstate runs on cold days 15-20 degrees, the water ran around 185 and oil as high as 218 but usually a bit lower. What's going on here? how could this thing be clogged again? It hasn't seem to gotten much worse since we got it back but not better either.
View 8 Replies
While driving home last night my truck started to overheat, the temp jumped from where its been running at lately (around 210) to 240, I stopped and took it easy getting home. This morning I sprayed down the radiator to clean out any mud that may have gotten in it from field work at the office (its always going through some pretty deep stuff). It ran fine for about an hour then it started to over heat again, I got it home and did a complete radiator flush and then did a test drive. It still overheated so I decided to try something, I released the pressure in the system by unscrewing the cap partially and drove it around again, this time it didn't overheat, put the cap back on and the temp jumped right back up to 240.
View 14 Replies
Trans temp used to be about 185 max, now it's running side by side with coolant temps (200-203 with Mishy 200 thermostat) after I did the 08 pan and filter upgrades. I added 9.5qts after the change of Valv Max Life and checked and double checked the dip stick bout half way up hot. This is normal operating conditions, not towing anything. Checked with TorquePro App. Why it would run so high? Did I do something wrong?
View 14 Replies
I have a 05 6.0l. Egr deleted. And my truck has a rough idle and power loss. Ive tested the ipr and the icp and they are reading at specs. I've also replaced the Hpop about 1500 miles ago. It has a real rough idle until it's at running temp. And it has power loss, I'll be driving down road and theres no where near has much power has there should be. And the idle will jump between 1500 rpm and 2000rpm.
View 9 Replies
I have a 2006 350. When I am pulling my camp trailer (about 12,500 lbs) up a grade I hear a fan or blower turn on and I get a high pitched squeal. It will also have a beep and my in dash display will say high engine temp. I have a bullydog pmt programmer (i tow with it in stock mode) the display will show my coolant temp at about 180 degrees. If I pull over and let it idle for about 2 minutes the warning clears and the temp gauge returns to normal. the display reads about 180 degrees the whole time this goes on. I know the engine is not over heating so why do i get this warning and squeal?
View 4 Replies
I have a code for iat sensor 1 circuit high. It's the only code I can pull. I replaced the sensor in the manifold and still no change. The truck revs up when started but kinda finds its idle rpm after a second and the idle fluctuates some when the truck is warmed up too. I have a snap on solus and all parameters seem to be good. Icp sensor is also new thinking it might be the cause. Other than that the truck runs perfect and doesn't miss a beat.
View 14 Replies
I'm excited to be a Powerstroke owner again! I had a 2000 with the 7.3L and since bought and now sold a Chevy 1500. Last week I bought a new 2015 6.7L. I am MORE than impressed and love the truck. Today I brought it to get the windows tinted. I have not had one issue with the truck since I have had it. When they finished with the windows, my check engine light was on. The shop I had it done it EXTREMELY reputable. They brought out their snap on scanner and pulled the code. p0073 for the ambient air temp sensor circuit high. Is this a coincidence that this came on after they got done, or could something they did while tinting the windows tripped this?
As I drove off down the road after determining I wasn't going to hurt the truck, the air temp sensor went from showing -40 to the actual temperature. What would cause this? I deleted the code when I got home with my actron, and the MIL has stayed off since, however, it shows P0073 Permanent ...
View 11 Replies
Ever since having the EGR delete done, the oil temp has been LOWER than the coolant temp. I am assuming this is bad info from the sending unit? They are reading with in a degree of each other at start up, but when at operating temp the gauge will read lower. Before the EGR delete I had a delta of about 4-7* oil hotter than coolant.
View 1 Replies
I notice my trans temp gets really hot fast. For instance just moving my trailer from front of my house to side yard makes temp go to 250. Without any load and driving a couple miles it does the same thing. It's been doing it since I installed the trans temp gauge just trying to figure out what's up.
View 14 Replies
I will start off with saying I am posting this for my dad. His truck is a 1999 F350 crew cab DRW 4x4 auto 7.3 with about 189K miles on it. He is leaving wednesday on a cross country road trip pulling a 40FT 5th wheel (no idea the weight but the thing is huge). He has glowshift gauges installed, one of which is the trans temp gauge. I believe the transmissions on these are 4R100, but I am not positive about that, but I'm sure many people here will know. He just told me that he had the mechanic he goes to replace the pan gasket on the transmission because it leaked quite a bit, just as a precaution. He also had them replace the brake booster as it was leaking inside by the brake pedal. When he got it back, he said he was driving it, and the temperature started going up to I believe 220 degrees not pulling anything. He said since he installed the gauges it has been between 180-190, and it jumped to 220.
What this could be. I have read that the TFT sensor can cause this issue, but it would throw a code and possibly go into limp mode. He has no check engine light and it was driving just fine. So the temperature is just all of a sudden high. Fluid level is fine, was checked after about an hour of driving, is red, and doesn't smell bad. I am suspecting the temperature isn't actually hotter, so there is another issue. It's only a big deal now because in a few days he will be dragging a huge 5th wheel behind him.
Last year, we towed some pile of crap 5th wheel down to our city for somebody with his truck, and we had to pull over halfway back because it started to smell like something burning. We think it was the trailer, as the brakes were questionable on them. When we got it to the people we were delivering it to, when we left, it wouldn't shift passed 2nd gear. He only lived a few miles from there, so he drove it home, parked it, then went out the next day and it was fine. He had the fluid flushed later and that issue hasn't come back since. No other work was performed on it since the pan gasket a few days ago. I am not sure if they are related being a year apart, but figured I'd mention it anyways.
View 12 Replies
I have an 07 6.0 diesel and I'm having trouble once it gets hot. It begins to lose throttle response and shakes while cruising and also has a rough idle. sometimes it dies while idling but after cooling off for a few minutes starts back up and runs fine. I've checked the high pressure oil and the ficm and both of those are fine. I've done an EGR delete so it has nothing to do with that either. My MPG also goes way down when this happens.
View 5 Replies
This is not on my truck. This is on my buddies 04 we just did the egr delete and oil cooler and a bunch of other stuff to.
Coolant temp doesn't go past 170 which I assume a new thermostat will fix this issue no problem.
but, the oil temp never goes past 140 no matter what driving for an hour at 70 and it doesn't change.
Bad sensor? Or would replacing the thermostat bring the oil temp up to where it should be?
View 6 Replies
I recently observed coolant temps of up to 217 degrees as reported by my mini max and oil of 230 as reported by the dash while towing 9000 pounds from San Diego to Las Vegas on the 15 going up the 16 mile mountain grade. My temp gauge on the dash never moved a bit, it stayed in the same spot from 199 to 217 so I assume its not too hot. My mini max defuel setting has the coolant temp at 220? I slowed down and tried to keep it under 210.
View 8 Replies
I have 2007 6.0, rough idle starts, rough and no power till engine reaches running temperature, runs great after that. If the engine is off for half hour, and restarted, runs rough again till engine temp is back again.
View 3 Replies
To start off. I have a 2004 F350 with the 6.0 in it which just had a top end rebuild done on it due to the head gasket blowing on it. During the rebuild the EGR cooler was also deleted, ARP head studs, Heads were milled down to make them flat (shop said they had to take 9 thousands off to do so), new up pipes installed, new back pressure sensor installed due to the plug head snapping off, new glow plugs, new glow plug rail harness, oil rail rebuilt due to bad o-rings on the ball tubes, injectors were installed with all new seals and had polished the spool valves hoping to avoid stiction (however its spelled can never remember), and lastly the EGR was deleted electronically with tuner. Also had to get 2 new batteries as they were stone dead and would not take a charge. And had to get a new alternator due to low output. Not sure if the alternator killed the batteries or the batteries killed the alternator either way it needed replaced to.. Unfortunately after i got that fixed i had to get a new starter as it died 3 days later.
Ever since its gone back together Ive had a consistent intermittent miss with the truck. Ive searched every article i can find but seems most complain about misses when cold. Mine is the exact opposite as it only does it once the engines up to normal operating temp. It accelerates hard and fast like it has no issues. While its cold it doesnt miss at all. Once its warmed up sometimes while cruising it will feel like its missing on every cylinder or better description would be as if your driving on a cobble stone road.. If you mash the pedal for a couple seconds till it kicks down and raises the rpms it stops.. Its most prevalent at idle though.. You can literally hear the difference in the engine when it starts missing. Truck will shake as if its got a large lopey cam. Odd part while sitting at idle it will cycle back and forth between running smooth and missing. But same with at cruise as soon as you get on the throttle it goes away. If its doing it while sitting idle at a light, it will take a couple seconds once your on the throttle for it to smooths out. But always does.
Ive tested the Ficm hot and cold, KOEoff and KOEOn.. getting a steady 48v from the main board.. Scan gauge says the Logic boards reading steady 13v... Also from the scan gauge it says my ICP pressure is in the 640 range at idle (full throttle highest ive seen is 3600psi so dont think its a pressure leak) and volts bounce between .80-.90.. but oddly once it starts missing the ICP pressure jumps up 20 psi.. IPR at idle reads 23.5-25.5.. at cruise its up around 45ish.. fuel pressures said to 70 psi.. which its usually around that most times, cruising itll be around 66psi. I had 3 injectors replaced not this past spring but the year before (ironically same symptoms).. Injectors 5,7,8 were replaced then.. ICP sensor was also replaced at the same time as it split and shorted out the connector which was the initial reason i took it in that time since it was dumping the oil on the ground.
I dont have any way to perform a cylinder contribution test and after spending 6K on a rebuild I really cant afford to take it in to have someone else do it. A local guy was able to scan the truck for me but he couldn't do the contribution test either but was able to buzz test them. Everything passed there but we also found some hidden fault codes my code readers did not find. The ones we found hidden said that injectors 2, 4, and 7(again??) are reading low contribution. Of what I've read 2 & 4 sit on either side of 7 in the firing order so have wondered if they're not pulling down 7's results.
I really cant afford to replace the injectors till near the end of next month. Is there anything else I can look at that might actually possibly be causing false readings or intermittent misses only when warm.
View 14 Replies
I've been searching for a while now but have not found an exact match to my problem.
So, Yesterday I was pulling a large load home (15K lbs) over flat land/small rolling hills and I experienced a coolant temp spike. And I am trying to figure out what caused it. I was traveling 65 mph about 2k rpm and 20lbs of boost, I was motioning the ECT, EOT, TFT, and Fan Speed via my scanguage and 99% of the time the ECT was in the 209-220 range, once it got up to 220 the fan would come on and the ECT would drop to 209 ish pretty quickly.
However, twice the ECT shot up from 215 ish to 240 within seconds then the dash indicator said check coolant temp then the fan came on and cooled it down to 200 within seconds, I did lose about 1/2 gal of coolant. So today I'm going to get a new degas cap (still OEM original) and continue to monitor the situation.
My EOT ECT delta has been a constant 10-13 degrees for the 3 years i've been monitoring it so i believe my oil cooler is still functions within spec and all my cold soak temps are within a degree or two for various ambient temps (20 -80) so all my sensors should be good.
Also, tonight I'm going to pull the EGR valve and check if there is any coolant in the intake, but if there is not, where should I start looking and what should I start worrying about e.g. head gaskets?
View 12 Replies
This is the only 6.0 I have owned. My tranny temp (with the Torque Pro) is pretty much always the same as my ECT. My ECT will move, and less than 2 seconds later, the tranny will move to the same temp. Is this normal? I was expecting lower tranny temps, but maybe it should be the same because of sharing the radiator.
View 11 Replies
Looking at another 6.0. It's an 2005 with 156k. When test driving it on the scan gauge water temp stayed around 160 and don't believe it ever went above 170 if it even made that. Bad t-stat? Or a more significant issue? The other issue I seen that concerned me, is cruising at 65 for 10 minutes plus to check deltas their was up to a 20 degree difference so I'm thinking plugged oil cooler and bad egr cooler. Temps were 190 eot and maybe 170 ECT. Wasn't sure if the water temp issue affected the results on this reading or not.
View 14 Replies
