I I have a pretty good o ring leak where the egr cooler meets with the intake. My question is can i replace the o ring without removing​ the intake. If so what is the process.
View 2 RepliesI've been watching fluid build up on what I think is the hi-pressure line on the hydroboost. It appears to be originating at the coupling in the line because it is dry back at the unit.
Is there an o-ring or nylon washer in this fitting?
Can it be tightened?
Does the o-ring or washer need to be replaced?
Is it a sign of something else, like a build up of pressure in the line that is too high?
I currently have zero problems or noise coming from the steering or brake system.
2 1/2 years ago I installed a BPD remote oil cooler with BPD filter. The stock oil cooler was clogging up for the second time and didnt want to chance it. The BPD oil cooler works great. I have never seen high oil temps in any driving condition. Last week I was replacing the hubs and seals on the front of the excursion and noticed the oil was leaking from the 90 at the end of the hose oil filter location. I called BPD and sent them a picture. The 90 is corroded and is failing. They said something about a 2 year warranty but because of the rust they would not send one out for free. I purchased a new hose and the other 90 that goes right after it.
They recommended that I spray it with undercoating or something. I live in upstate NY and deal with a lot of salt on the roads in winter. I do keep the truck clean in winter as much a possible. I am posting this so if there are any others in similar situation you should do something to prevent that 90 from rusting like mine did. If I had known this when we installed it prob would not be replacing it now. Will be replacing it tonight or tomorrow. BPD said I will need a 1 1/4 crow foot or remove the turbo to get to the other end of the hose. Not posting this to bash on BPD just sharing so any others can prevent this part from rusting out.
I installed a BPD EGR cooler about 4 years ago just as a preventative measure (along with an oil cooler) in my '06 F-250 6.0. About 6 months ago some coolant was found to be coming down the rear of the engine and onto the garage floor but only in the mornings after cooling down and even then not every morning.
A couple weeks ago I did a coolant flush and put the red ELC coolant in and now I can see better where the coolant is coming from. It appears to be coming out from the O-ring between the cooler and the intake manifold. I did check the torque on the stud and bolt and they are tight.
Is there a way the drop the cooler enough to install a new O-ring with out going through the whole process of removing the intake manifold and everything that is associated with that? The thought is daunting...
I have a 2005 F250 with 6.0 and almost 175,000. On vacation right now and noticed when I came out of a store that there was a puddle of water under the passengers side. Chalked it up to AC defrost. The second time I was not running AC and puddle again.
Felt and smelt of it...antifreeze. Just put in all new Zerex G05 and a new degas tank because when working on it I noticed a pin hole in the base before we left. I replaced the EGR cooler and hose from Sinister about 3 plus years ago.
Would the EGR cooler hose be leaking? I've noticed that white residue on top of the intake around the where the hose is. What would cause this, Heat, wear and tare....my luck ?
I am doing the usual upgrades on a 2005 F250. What started as a small leak at the rubber coupling between egr tube and oil cooler turned into doing everything else while motor is down this far.
I am curious what the difference in the upgraded oil cooler is? Well besides not prone to failing as early.
Can I change these out to hydraulic hoses with clamps that are rated for the fluid. Mine are rusted and starting to leak.
View 6 RepliesI just replaced the oil/egr cooler, stand pipes and dummy plugs along with all suggested upgrades, just filled with oil hooked up batteries and while filing with coolant it started gushing out from under the intake in front. I think I see an o-ring pushed out.. I hope I can lift the intake without removing the turbo!!!
View 1 RepliesI have a 04 that has 153k on it. 4" cat back exhaust with no cat. SCT tuner running a custom street tune. New FMIC with the extra tune on it. Head gaskets where done at 90k along with ARP studs. EGR cooler, The oil cooler was cleaned, New coolant tank. 1-new head and The cooling system was flushed at 90K. All done by the dealer along with some other items. Installed a bypass coolant filter at least 60k miles ago.
I have been having a no heat issue sometimes at idle this past winter and a mystery loss of coolant. I replaced the cap with a OEM one. I did a vacuum test on the coolant it held at 25 inches for well over a 1/2 hour. Pulled the egr valve it looked somewhat like tar inside not 100% dry. At startup it sometimes blows some white smoke and other times it's black smoke. I've had the scan gauge on for the last week to check my deltas.
Running 65mph the deltas stayed around 10 degrees diff.
Running 70mph the deltas stayed around 14-16 degrees diff.
Yesterday just running around rural roads 55mph and under the deltas stayed around 10 degrees diff.
I have not found a lower pressure gauge to do a coolant pressure test.
It does look as though it has burped the cap. Because of the deltas I'm thinking a plugged oil cooler my be the problem.
I'm doing standpipes and dummy plugs. There is a 4mm plug with an oring and mine was trashed. What is the P/N?
View 13 RepliesWhat is the consensus on this setup? Is it worth the money? Or is it more hype than function? Their logic behind it definitely seems to make sense.
View 11 RepliesJust found out that my EGR cooler is bad. How big of a job is this/how much down time if a compatent tech is doin the job?
View 14 RepliesI just replaced my oil cooler and 500miles later its clogged again. Delta reached 40F.. No fun... I replaced it with the factory ford cooler and installed the coolant filter but I guess when I did the first flush I missed sum gunk.
So my question to you PROs, should I reflush/restore again then replace the cooler? OR Go with one of these??
- Coolant-to-Liquid Oil Coolers
- IPR External Oil Cooler Kit for Ford 6.0 Powerstroke
The budget is tight, but I gotta keep the truck going.
I'm considering the BPD cooler MINUS the filter. Anything wrong staying with the original filter?
View 7 RepliesWell it looks like I'm going to have to put a new oil cooler on my truck. Does ford have an upgraded version or do they still offer the same cooler?
View 5 RepliesI have a leak in my inter-cooler system. I have replaced all the hoses. Is there a reason I should not pressure test the system with 20psi? 2001 F350 7.3 turbo
View 4 RepliesMy 2011 has 62k miles and has been throwing P0401 codes, which results in losing power. I assume the EGR cooler is clogged. So I went to the dealership to see if it's covered, and was told there's no warranty coverage.
I would rather blockoff the EGR cooler than repair it. I would also like the extra performance from a tuner like the MiniMaxx. I do prefer the stock exhaust and not real excited about the drone/smell that comes with deleted DPF.
Will I have issues if it's tuned with the EGR blocked off, and stock exhaust? Or am I better off doing a full delete at this point?
My truck threw a CEL after the first start today. The CTS reports it twice. I noticed it about two minutes after start.
P02E1 - Diesel Intake Air Flow Control Performance
The air box gauge is green and it doesn't reset when I push it so that appears to be fine.
The one thing I can easily notice is the sound of the turbo. Typically when I stop and park, the turbo spools up, then down, then spools again and gives a sigh of relief and it's then silent. It's not doing that currently.
Now, I can hear it constantly when parked and it spools down after I turn off the engine, even two minutes later. That is not normal for my truck when I wait for the above to finish its routine. When I start the truck, the turbo immediately spools to where I can hear it which is also not normal, as if it's building 0.5 psi. I realize that's funny to say on a turbo diesel but I know the sounds of my truck. The EGT's are fine, EOT, ECT, TFT are fine and I can build boost when driving without issue. I took the drive to work easy this morning so the highest I noticed was 10 psi.
I restarted the truck after a 20 minute drive to the office and it didn't clear the CEL. The CTS squawked four times when it woke up the second time but it didn't show me which PID it was upset about.
I'm thinking this has nothing to do with the CAI and this is something downstream of there. EGR related? I haven't opened the air box yet, at work and in dress clothes so that'll need to wait. My past four or five regenerations all started between 1.94 and 1.97 soot gpl. That is also not normal and is something I have been keeping my eyes on. Currently the DPF is at 2.10 so it has made it further. Normal behavior (post emissions flash) is above 2.54 soot gpl for an AR.
Is there a way to fill up the reservoir for hpop and cooler after replacement? I didn't want to burn down the starter and kill batteries cranking all day until everything is full. I did the usual upgrades on the motor and about ready to try and get it started up. Where does the oil drain to when filter is removed?
View 3 RepliesMy dad's 03 has had some work done after his oil cooler was clogging. New oil cooler, egr delete, head studs etc. The oil temp seemed to run some what high when he got it back. After a couple interstate runs on cold days 15-20 degrees, the water ran around 185 and oil as high as 218 but usually a bit lower. What's going on here? how could this thing be clogged again? It hasn't seem to gotten much worse since we got it back but not better either.
View 8 RepliesGot everything done today. So I thought. Went for a drive. turbo not building boost. I checked the map hose and barb. Clean. Checked connection at ebp and vct, both plugged in. No exhaust leaks. turbo shafts feels good and spins good. made boost fine before repairs. 2006 6.0 f250 .....
View 14 Replies