I'm new to the Ford 6.0 diesel motor just got one from someone and the fusses and relays have been messed with. I have fuel up to the second fuel pump and it sounds like it's working but It just turns over. I purchased the Haynes manual but it doesn't have information on how to test the injectors or fuss box set up.
View 8 RepliesSo loss power on take off and then stopped at store quick shut it down. Came out of store ten minutes later no start just turns over and over. I replaced IPR last year the one on passenger side near frame if that's correct and perhaps this is the ICP near back of engine?
View 14 RepliesI changed out my fuel filters today on my 2016 F350 SD and right parts, no leakes, main filter full, and I did the 6 cycle fuel pump prime. Turns over but won't Start. Redid the 6 cycle prime several times now and still no start. Pulled the 2ndary filter lines while it was priming to see if flowing and got squirted on both lines.
View 8 RepliesTurns over great but nothing. just changed fuel filters all voltages read great. I have ScanGuage and what little I can tell everything reads good. Has been acting funny for a couple weeks taking 4 or 5 cranking attempts to start every now and then no real pattern. Runs great when going even when pulling a load. It has failed to start and I'm in my shop and not sitting on the side of the road.
View 6 RepliesI have a problem with my F250. The engine is turning, rail pressure 400kpa, but it does not jump at. Injectors are tested at bosch. High and Low Fuel Pressure Pump are new.Sensors and pressure regulator also. Compression is also ok on all cylinders.
View 4 RepliesI "Bulletproofed" my f-250 Super-duty last summer and she ran great for a time, actually she is still running great, except for one thing that is driving me crazy. On a cold start it turns over until the oil pressure builds up. Then she will crank and runs fine, also starts normally after warm, turns over a couple of times and cranks.
I have oil in the filter housing, have replaced the seal at the bottom of it. Just pulled the oil rails off and replaced the seals on them, and a new IPR seal and filter. I am still having the problem, F.I.C.M. voltage has been fluctuating between 45 and 46 vdc. I have a P300 and P308 code.
I haven't really considered Injectors because it is idling smooth as silk and has great power.
As the title says I'm driving down the road and the radio just turns itself off, If i hit the power it turns on but it's like a ghost hit turned it off.
View 4 RepliesWhen I start my truck up and leave the parking lot from work I have to take several turns. When I do this it feels like there is no fuel getting to the engine and the truck acts like it is going to stop. I assumed it was some kind of fuel issue and thought it would clear itself up over time. I have had the issue with my truck for several months now...
View 4 RepliesJust bought a 13 6.7 used. It is in excellent shape but, you turn the key off and it is a few seconds before it dies? Is this maybe something aftermarket the previous owner installed?
View 8 RepliesGot up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
I have an 03 f250 that i think is getting air in the fuel line when it sits. It turns over starts and immediately shuts off. Then i have to crank it for a minute or so before it will start. After that it is good all day. Next day it might sputter on start but stays on. More than a day it shuts off immediately and needs cranking for a minute...
View 13 RepliesI bought a 99F350 with a 7.3, it was not running when I bought it. Batteries good, new starter, turns over just fine, fuel pump works, but now I don't know what to look for.
Was testing ohms for my injectors and at the plug on top of the driver side valve cover, couldn't get a reading at all, tested the ohms at the pass. Side valve cover plug and got good ohm readings.
Ok I'm working on a 2000 7.3 on a F550 truck was running but had no power so we changed out all the injectors and glow plugs and rebuilt the turbo now there is no start it turns over and were getting black smoke from the tail pipe. What is going on with it?
View 2 RepliesHad long start issues. Would turn over for 5 seconds - shut off- turn over for 5 seconds - shut off - third try on 4-5 seconds the low oil pressure would come up and HOP would fire injectors and start up.
Was not sure what was up, so look it to Ford. They did leak down test and found seal at the top of injector 4 was leaking. Replaced it and leak moved to other injector. Basically moving to the next weakest seal point. I told them to stop as i did not want to pay, parts, labour and shop time to replace all injectors, etc. They also said power across all injectors was good, but 3 & 7 were not contributing on cold start.
I drove it home and bought parts. New cups and seal for all 8 on fuel rail. New gasket kits for injectors. Plus 2 new injectors to replace 3 and 7.
Replaced injectors in 3 & 7 with the 2 remanufactured i bought. Replaced all cups and seals on fuel rails. So it has new injectors in 3, 4 & 7.
As for the other injectors i took the 5 of them right apart and cleaned them and re-assembled. Took about an hour per injector, took my time to get it right, just FYI. Went pretty good i thought. Seemed pretty straight forward actually.
Now no start - no high oil pressure at all. LOP comes up right away. Scanner shows no HOP no matter how long i crank it.
FICM power good, 47.5 - 48
shows FICM sync - YES
IPR sits at 14% and jumps to 84% on crank - starting, see photos below.
Scanner prior to crank
Scan during crank
Note zero IPC - PSI
Right now.... Got the valve cover off on passenger side. Cannot see oil squirting out the sides of any injectors, but line of sight is limited. Maybe need a small mirror to see in there. LOP comes up better than it has in years, but no HOP now. Before rebuild it seemed i had good HOP but low LOP.
I drove it home from Ford and into my garage, so i do not believe the HPOP crapped out sitting in the garage, so i am ruling that out as a fail, at this time.
Dummy plugs were replaced 5 years ago and o-rings looked decent.
Pulled the small plug screw at the top of the fuel rail. Cranked it until oil came out, bleeding air. then replaced the screw plug. Have not done that on drivers sideyet. Will try that tomorrow. However, think this is more than an air issue, as i have cranked it over plenty, unless i just have that much air.
Going to pull the valve cover on the Driver's side tomorrow. Then will have both covers off at same time to view all.
Noted that if i put compressed air into the screw hole on top of the fuel rail, i can hear air coming out from below the fuel rail. Nothing at the base or around injectors. Does not seem to be at the cups either.
Just wondering.... Buy applying air to those screw plug holes, is that the same as doing the air test at the sensor that pokes up through the valve cover.
With air pressure at these scew plugs on the fuel rail, should this be sealed and be air tight and hear no air leakage. Because it was not air tight on the drivers side before i closed that side up. I am curious about this.
I am assuming i still have a HOP leak. I do not think i have a failed HPOP. How to better chase a HOP leak?
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 RepliesHave a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesI was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 RepliesDon't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
Long story behind it but finally got my scanner working right and checked the suggested systems for p2290.
IPR was 77+ on start up dropped to around 31 at idle
FMP is in the 46.5 to 47.5 range
SYC was at 1 and occasionally at 1.5
ICP was at 550-650 during startup and quickly ramped up to 1150 then settled into around 850 at idle.
The only thing that I'm not sure of is the IPR being 31 at idle, is that what it should be. The others I think are within normal operating parameters.
The truck starts but has no power. Can barely go up a slight hill on my street. Seems like it's going to be fine but as soon as I apply a little gas it just falls off.
This is a new truck to me 03 Excursion, the owner has done a lot, gave me receipts for a lot of work and cosmetically it just seems taken care of. About a year ago hpop, ficm, oem egr and 3 injectors. He wasn't happy with that mechanic and still having problems so went to a different (supposedly better) shop. This time turbo cleaned, all 8 injectors and passenger head was redone and put back on with oem bolts. Apparently it was found that a nut was dropped down valve cover by the first shop! Somewhere along the way the ICP and GP module has been replaced.
I've only driven it a couple times and seems great until last night. It was loosing power and in about 10 seconds died and wouldn't start back up. Pops but doesn't stay running. WIF dash light on and no CEL codes. Not sure where to start/what to do. I've paid for most of it and was planning to pay the rest and transfer title but I'm not comfortable doing that till I'm confident it's good to go.
I drained the separator and seemed to gush out like it should and don't think I saw water. I'm planning to take the sensor off the filter there, inspect and clean it but I don't imagine that's the problem. I do see oil coming on the back of the engine and front of tranny on the drivers side... maybe ICP is all oily and failed? I don't know much about these, just been trying to read. What should I do as some first steps? Do I need some sort of scanner? It seems like it's starving for fuel. It was about 1/4 of fuel when I bought it and filled it up the night I took it home and have put about 80 miles on it since. Is it possible it's got bad fuel or water?