Ford 6.0L Power Stroke Diesel :: No Start / Cranking And Large Pop Noise Came From Under The Hood
Mar 13, 2016
Had Just replaced glow plugs and batteries along with a new set of tires. Truck had been running fine for the three days that is was. Went out the next morning and went to start and "POP" a large noise came from under the hood. I have yet to discover where this noise particularly came from or what it may have been that caused it. But ever since the POP it will not turnover what so ever. Key on every thing is normal all power just when go to turn key over it makes a faint click. You can feel the click in the relays on your hand when you try to turnover. But nothing. I am absolutely clueless.
View 14 Replies
Advertisement
Scangauge reads icp ok. Ipr ok. Fmp voltage is all over the place from 42 down to 2. Flp is also all over the place from 11 down to 2 volts. And no Sync. Load checked batteries well. Voltage is 11.5 down to 10.5 when cranking. Fuel good. No pre warning signs. Parked running good. I have read tones of forums but none with 3 issues. Could it be the relay?? Would a bad ficm show no sync on cranking?? Why is my flp voltage so up and down.
View 14 Replies
Finally got everything buttoned up, and truck was going for it's first drive today. Started cranking, and it just barely tries to start, and then nothing until I cycle the key again. Doesn't even give me a full Vroom, Just like a Vro- and then back to cranking.
I've had it started and running a few times, so something has changed. And to add to the fun, something between my tablet, my torque pro app, and my dongle isn't playing nice. Tablet just won't see the dongle. So I get to figure that out too.
View 14 Replies
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 Replies
I need to start ford power stroke, 2005 with vt365 engine, is v8 cylinder, front timing cover was change and since then the truck only cranking and refuse to start, what have done so far, test icp power, ground and ecu 5 reverence voltage was ok,crank engine and monitor icp signal voltage was 1.2 and above at a crank,installed 1500psi gauge in icp hole and monitor oil pressure at engine crank reading 800psi and above, fuel pressure was 45 psi and above, check engine rpm was 175 and above, measure cam sensor ohms was 800 and crank sensor ohms was 400, check cam and crank supply power was 1.87v and ground was ok, replace ipr with brand new, no fuse that cut, scan for code i found(221 internal sensor supply voltage low or below normal range FIM4)FMI4,Engine crank but no smoke from silenser, using fluid and yet engine didn't make any attempt to start was only cranking, what could make the engine not to start and which component has failed that display above code.
View 14 Replies
This morning when attempting a cold start of my 05 6.0, it would not start was noticeably harder cranking. I had no CEL. I checked my scan Guage and the volts were 13.4 and fcm main power was 48.4. I checked and I had a p0405 code. What could be going on? I read that it can be a stuck or bad EGR valve? Could it be battery related?
View 9 Replies
Dang, won't start again. My auction truck needed batteries, so I put mine in it and bought new ones for my work truck. Couple of days later, didn't start. Checked SG and I wasn't getting enough RPM. Jumped it and it fired right up. Replaced one of the new batteries and it's started fine the last few times, until just now, in the parking lot of the tire store.
The RPMs were weak - they'd go over 160 but then fall back to the 140s. I walked home and got my auction truck, jumped it, and it still doesn't start. Just spins. RPMs still fall back to the 140s after a few seconds of cranking, but they got as high as 220 so I don't think that is the problem. Fuel pump runs, the upper bowl is full, no bubbles. Oil pressure registers on the dash after a few seconds of cranking.
The last time, I wiggled some fuses and it started. Not this time. FICM at 48, ICP around 700 while cranking. Volts and IPV are good. FPW is 0, but I think that's right, until it cranks. Same with Sync - at 0 while cranking - does it ever go to 1 without starting?
It acts like it has in the past - cranking just fine but no start. And in the past, when it finally starts, it acts like nothing was ever wrong. I checked my IPR screen about a month ago after replacing it about 6 months ago when it didn't start. What am I missing? I'll go read some threads for clues.
View 14 Replies
I just finished installing a new set of injectors, standpipes and the blue spring kit on our 2005 Excursion 6.0. The truck idles and runs much better but now it takes almost two seconds of cranking to start the engine. Cold and hot are the same and the length of time between shut down and start doesn't seem to matter either.
What to check? I am planning to check the ICP tonight when I get home. Could I have air trapped some where in the system? This is my first powerstroke so I don't know if this is a possibility.
View 8 Replies
About 7 months ago my truck started cranking longer than normal to start after sitting for more than 2 hours. This went on for about 3 weeks, then it started normally again. (By longer crank time, i timed it between 5-7 seconds on average. Normal is about 2 seconds). Now it has started doing this again about 4 weeks ago. Now I'm thinking HPO slow leak. Yesterday all is good again. What should I be looking for as a starting point to fix this permanently? When it cranks longer, the icp stays at 0, the ipr goes to 77%. Then it just fires off. No slow build of pressure. You can see all my mods and updated parts in my sig. I wonder if one of the new dummy plug o-rings is starting to give up already after only 15k miles. (Batt voltage is at 13.9-14.2, ficm is at 49.5 steady).
View 5 Replies
I have a 2003 f350 6.0. awhile back i was driving down the road and it died. popped the hood and there was a small amount of oil sprayed on the hood. rocker arm bolt had broke. that's been replaced and no it won't start. cranks and acts like it will what to fire for a second then it just cranks and does nothing. reading the tech on no start issues theres a lot to look at.
View 6 Replies
My 2011 F350 - 6.7 has developed this KRAZY thump, snap noise under the hood, loud enough to be heard inside the cab, and I cannot find out what the heck it is. It is not directly connected to the motor, you can rev it and the noise does not change. the thump is like, every few seconds or so, especially when the motor is cold. I am afraid this is a 2000 dollar noise and the truck is out of warranty.
View 8 Replies
I have a 2011 f250 6.7, I park under my house everyday, so I am used to weird noises coming from my truck when I shut it off, but now that I just did a dpf and egr delete, and tuner, I noticed that my tuner doesn't shut down until the noise under the hood stops, which takes a few minutes to stop, I use to hear the air valve on the egr cooler shut when every got quiet, but I don't remember it lasting this long, any one else have a H&S mini max and it doesn't shut down right away? the place where I bought my mini maxx said it should shut down as soon as your head lights go out, but that's not the case, the headlights go out long before this noise stops and the tuner powers off
View 10 Replies
Just pu my new 2013 6.7 Diesel with 1300 miles... There is a most annoying whining coming from under the hood and sound like its coming from the secondary filter area or turbo (you can even feel it if you put your hand on the filter lines and housing) and it starts a minute or so after the vehicle has been running and you can her in the cab at 70-mph... At drive through restaurants I have to shut the tk down to place my order and never goes away..
[URL] .....
View 14 Replies
I have a 2006 F350 6.0L Powerstroke. While towing my RV this weekend in 96 degree weather, it appeared that my transmission started to whine after several minutes of pulling some large hills. I was in tow/haul mode. It did not appear that I was loosing power however the sound was very concerning. The sound went away after leveling off, or switching out of tow/haul mode. The sound coincidentally appeared as I approached the top of the hills which ranged from 1 to 3 miles in length.
View 11 Replies
I've been trying to figure out a slow start condition on my 06 F350. What should the starter rpms be when cranking? My scanguage reads 180. Does this sound low? Batteries are new.
View 9 Replies
Cranking without fuel is probably never a great idea - but it happens - maybe after repair or when someone runs out of fuel, etc....
Is it any harder (worse than usual) on these Bosch fuel pumps than any other vehicle? I realize that the closer tolerances and the very high pressure might make things a little more fragile in a "no fuel" situation...
This question came from a discussion that I was in (maybe beer was involved) a couple of days ago... Of course we had 4 different opinions... I would like to know the facts - if someone is more qualified then us "redneck mechanics"
View 12 Replies
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
View 11 Replies
Some information about the truck2004 Excursion, Motor has a December 2003 built date listed on the valve cover
Bullet proof complete by Hallas performance just prior to Mike's passing (3 years ago). ARP, EGR, Oil Cooler, lifters, etc..
Newer batteries, DC amp 185 alternator, newer starter, she cranks hard and fast~230,000 miles
Here is the situation: Starts good and fast when cold, even subzero temperatures. She cranks long and barely catches if I make a short stop at a store or restaurant. A few hours later or the next morning is fine.
I found the following codes:
P2284 - Injector Control Pressure Sensor Circuit Range/Performance
P2291 - Injector Control Pressure Too Low - Engine Cranking
P0528
I took her into the local Ford Dealer for diagnosis and here's what they reported. ICP tests good and has the latest pigtails. They reported a leak in either of the following.
Oil injection pump Estimate of 8.5 hours to repair.
Under the Valve Cover Gasket. Estimate of 3.5 hours to repair.
So here are the questions I have. Does this diagnosis sound appropriate? Is it reasonable that they do not know which area is causing the problem? Are the hours reasonable estimates for the repairs? Assuming I go ahead with these repairs, is there anything else I should have them look at while they're in there?
View 14 Replies
I have a 03 f250 6.0 . I rebuilt the whole top end. When i finished it 15 months later due to personal issues I started it. It ran for about 4 hours i turned it off the next day i went to start it again and didn't kick over so i figured it was batteries they might of died (it was about 3 degrees out) so i went to get new batteries put them in and it started using diesel 911 and starter fluided i let it run for awhile. I went back the next day to start it and it did t turn over it just kept cranking and started to die out so i stopped trying. Now a week later I am at it again. Could it be not starting because of bad fuel trying to get through the system or could it be something else?
View 3 Replies
What are the odds that the fly wheel is ok and I just need to replace the starter? I can hear it engage the flywheel, it's making the zzzzzzzzzzz noise after it disengages the flywheel, can these starters be oiled or anything to prevent that noise?
View 7 Replies
2005 Ex with 6.0. It has been bulletproofed. But has had a long crank after sitting for over 5 hours. I was starting to think glowplugs but no codes, Then thinking FICM, nope voltage has always been good. After I run the truck for a few miles if I kill it. It would crank right up. No issues. Only happened after it sat for awhile. I knew it had to do with HPOP system since it took about 5 to 8 seconds to show over 500PSI.
The passenger side does not have a leak since the oil is to the top of ICP sensor. When I was going to remove it. So I took off the drivers side. I inspected the dummy plug. No issues there "they are the 12mm with teflon plugs" I inspected the stand pipe. No issues there either. I inspected the small test port on the top of the rail. No issues there either. So I decided to air test it. So I used my auto-ingenuity to close the IPR valve after I heard all the oil blow out.
Then after sitting with 120 psi of air for about 10 minutes. I hear a bubbling sound coming from the Drivers side Rail. It was a plug I have never seen mentioned here. It is at the back of the rail. I removed it and sure enough the oring is split in 2. I went to ford and picked up a new Oring it was like $4. It also looks like its a different material. I am still in the process of putting the truck back together so i have not started it back up. But I am pretty sure this was my problem.
View 9 Replies
