Ford 6.0L Power Stroke Diesel :: No Power - Studders And White Smoky Exhaust When Warm
Mar 23, 2016
Say I just purchased an 06 f250 crew cab with the 6.0.
I had her trailered home due to dead batteries. I got her started up and drove about 5 miles until she got up to operating temp.
When I came to a stop and tried to accelerate, she immediately bogged down and started studdering with white smoke coming from the exhaust.
I shut her down and started her up again. She started and idled fine, but as soon as I pressed on the accelerator, she bogged and studdered again. I shut it down again and started it back up. Normal idle, and I shifted her into gear and was able to mozy on idling forward without having her bog, but as soon as I touch the accelerator, she bogs and studders.
I towed it home and the next day (today) she started just fine and I shifted her into drive and moved it forward about 10 feet. Did not touch the accelerator so she didn't big or studder.
1. I am guessing the white smoke was coolant burning through a failed EGR circuit. Do you seasoned members agree?
2. It the a check engine code when studdering. I have yet to check codes so I am still in diagnosis mode.
3. I plan to block off the EGR pipe and throw in a new oil cooler. Anything else immediate I should be considering??
View 14 Replies
Advertisement
I just looked back and it has been since July 7th that my girl has been sitting in my shop. Well this past weekend I finally got her back together and started. It took a while to build pressure but she finally came to life..
While I am thrilled that she is running again i have low power before the boost kicks in and is idling rough with a blueish- white smoke coming out of the exhaust. Once i kick her a little she will get up and go but I've never had the smoke before.
I'm thinking maybe a bad injector???
View 3 Replies
My truck is puffing smoke after about 10 minutes and warmed up (looks white). It happens only one time for about 30 seconds and looks light grey or whitish in color, definitely not black smoke. The truck runs just fine, starts great, doesn't hesitate or studder, doesn't loose any coolant, no signs of pukage. In other words, it Runs perfect.
By the time the smoke happens I am usually at an intersection and see this white smoke billow past me or see it in the pass. side mirror. it's too hard at the time to get out of the truck at that exact 10-15 seconds it smokes to smell it or see it's true color without my sunglasses on but it looks white or greyish. not convinced it's a blueish color.
The truck doesn't smoke at start up or run rough so I'm ruling out injectors. I think it might be the egr cooler that is still connected eventhough there is no hot gasses going through it. (Did the up pipe mod). I might have an egr valve that has a bad seal on it. I'll have to remove the egr valve and see if it looks gummy in there since the egr cooler still routes coolant.
The other thing it might be is a bad oil seal on the turbo which is burning off leaked oil after it's warmed up, again I don't see it smoke for the rest of the day.
The very first time I saw it smoke was the day after I did the up pipe mod and capped off the egr cooler. I may have had a small cooler leak before I did the up pipe mod and now the coolant (if it's coolant) can't run in the exhaust or burn off there directly. My SCT turns off the egr valve but the valve may have a bad seal in it along with a defective egr cooler. will remove the valve to inspect tomorrow if possible.
View 14 Replies
yesterday I went out started my truck and white smoke started coming out my exhaust so I turned it off waited a bit started it back up let it run for a bit smoke went away drove it about 60 miles. Later that night it did the same thing but I was 2 gallons short on coolant drove it another 60 miles ran fine. Next morning decided to take it to a shop put more coolant in it drove maybe 20 miles to shop got there turned it off everything was fine never over heated once. So this shop is now telling me my trucks hydro locked and I steamed the EGR valve. And there telling me it's gonna be $8000 to fix it .
View 3 Replies
I was passed the other day by a newer (square mirrors) nice-looking Super Duty that was slightly spewing white exhaust smoke. As a life long truck driver, I know a few diesel smells (and I kinda like some ). But, this was so pungent that it was irritating my eyes inside my own cab.
It was so irritating and nasty smelling, that I had to slow down (to let him gain some ground) and open my windows to clear out my truck. So that I may be better informed, what could've caused this?
View 14 Replies
I have a 2006 F350 6.0 litre diesel. The other day I started it up drove away and it was blowing huge plumes of white smoke out of the exhaust. Shut it off.....started it up again after a while then went on a long drive and it went away. What that was?
View 6 Replies
2005 6.0 & noticed on Friday there was white smoke coming from exhaust that started when I'd turn on truck then aster 1st light or stop sign it would be a cloud of white smoke. Once I start to drive it stopped & I didn't see it again that day. I noticed the same thing again on Saturday & Sunday but the smoke was thicker on these days but would stop like the day before.
I had a code come up a month ago which I believe was P404 but read something about EGR valve. So I replaced the EGR valve 3 weeks ago & light never came back.
Today I had a Dr's Appointment and had usual white smoke in morning but once I got to the Dr's appointment the truck sounded like the turbo got louder then usual and started to see cloud of white smoke again. While sitting in parking lot I check to see any codes but nothing came up but the cloud of smoke started.
When I left my appointment, the turbo sounded louder still and noticed white smoke every single time I stopped at a light or stop sign.. Then the coolant level was high with the engine giving me the warning of over heating coolant or something like that.
View 2 Replies
Having trouble with 6.0 powerstoke white smoke out exhaust. We have installed egr delete and still have white smoke and water coming out of exhaust not as much as before. Took it back apart to see if we did anything wrong everything look ok. We did a compression test on all cylinders they check out ok.
View 6 Replies
After a couple of setbacks, including forgetting to install 3 out of the 4 orings on the oil cooler, I got the IPR Gen2 delete installed. I have a couple of issues since getting it started. I have low boost, I know the up pipe for the turbo is seated well, really surprised about that. However, the exhaust pipe may have a slight leak, but not positive. Finally, the last on this issue, I have a ripped MAP hose that I'm going to replace.
Next issue is that I hear what almost sounds like a gas engine exhaust rumble from the front of the truck. What it could be? I had white smoke initially coming out of the exhaust, but it cleared up after getting everything up to temp and taking it for a ride down the road. On a side note, the leak that I had from my previous thread seems to be gone now.
View 3 Replies
I noticed a rough idle after driving an hour with a 6000 lb trailer and stopped at an offramp. Had no performance issues to that point in an hour drive. Then I noticed a good amount of white smoke coming out of the exhaust. The idle felt just like when I had a contribution/balance code on #5 a year ago, and a new injector fixed that. Before long (10-20 minutes later) the idle got real loud, like a big knock/loud tick every revolution.
I had a bunch of stored codes, so I reset them and later found a P0281 - Cylinder 7 contribution/Balance and P0404 - EGR control circuit range/performance were the 2 that came back. I drove it 2 more hours to get home. It ran well under load, but coasting or stopped gave the loud knock, and stopped and idling was a rough, inconsistent idle. It even stalled on me 3 times when braking for a red light (auto trans). There was a lot of white smoke all the time, plus a little dark smoke on acceleration.
What would you recommend for troubleshooting steps? I could put a new injector in #7 and clean the EGR valve, but want to have a good idea that will fix it first. Is there a good chance I have a messed up piston in #7 now?
Codes I cleared:
P0148 Fuel delivery error
P0234 turbo overboost (i know i need to pull and clean the turbo anyway, unrelated to today's issue)
P0281 Cylinder 7 contribution/Balance
P0404 EGR control circuit range/performance
P0670 Glow plug (I had the module unplugged a while ago)
P0683 Glow plug (I had the module unplugged a while ago)
View 14 Replies
2007 F550 with the 6.0. About 2 months ago I replaced the EGR cooler with a Bulletproof cooler. Truck ran well for a few weeks. Then I started getting the "turbo fart". I stopped using the truck until I had an issue with another truck. I was stuck so I sent the 07 out without cleaning the turbo. This morning a decent amount of white smoke started coming out of the exhaust. The smoke would sometimes get a bit gray. Going up hill it didn't have much power at all.
View 8 Replies
Today I drove to dinner in my 2012 6.7 with no problems then on the way home my brother said he noticed my truck was white smoking quite a bit and he said there was a very strong exhaust smell coming from my truck ( he was in his car behind me) I ran a diagnostic test and what came up was code P0401 (I believe that's right). Need to figure out what is going on with my truck before I take it to the mechanics and get charged up. The truck still has DPFs in it just has a DPF back exhaust and has a AFE cold air intake running on a stock tune. However I do have the DPF deletes and EGR delete sitting in my garage just haven't gotten them on the truck yet.
View 2 Replies
I have a 2006 F350. It started running rough and white smoke from the exhaust. I did an injector buzz test and found no codes. Cylinder contribution check showed cylinder one was not functioning. I replaced number one injector, cleaned injector cup installed new injector and copper washer. Engine runs the same. If it was a wiring harness issue should that have shown up in the buzz test?
View 8 Replies
Newbie hear to the 6.0L's. But I'm learning an awful lot really quick from all of you here. I've read lots of tech stuff on these EGR Coolers, oil coolers, FICM tests. This is what I got happening right now.
2004 F-250 6.0L. Today was 45 degrees in Reno. 5400 ft elevation. Tried to start it without block heater. Would not even crank. It tried to crank but sounded like it locked up on first crank. Tried again, nothing. Same. Tried yet again and finally got to getting the engine to crank, but wouldn't start after about 5 seconds of cranking. Waited a little while not wanting to burn out my FICM, then tried again. Same as previous, would crank but not turnover. Checked batteries. Both were over 12.3 V cold, motor not running. This next time, turned key on and let it sit in ON position for about a minute. Then cranked and it took about 5 seconds and then the motor finally cranked over. Lots of black smoke as usual for a cold start like this. Battery volts after cranking over and running were now both over 13.6 V.
Keep in mind the truck has started better than this before in 15 degree weather just about a month ago.
After it started I noticed what appeared to be oil/coolant residue directly underneath trucks transmission area. It was not tranny, but in that area. I got under the truck and can see this fluid coming from EGR Cooler area.
Now for the smoke. Just stared smoking on start up. White smoke. Then it would disappear as engine warmed up. Now its constant white smoke when warmed up and applying the throttle. Smells like coolant coming out of exhaust. Not diesel.
I parked truck facing downwards on my driveway. Then I checked EGR Valve. When I pulled it it was WET. Not dry. Peeked in EGR Valve hole, didn't see coolant. Just wetness. I did change gasket and rings on it the day before as well.
As for FICM, it reads 47.9 Volts on key turn, 48.1 on cranking and 47.8 running. FICM good by all standard 6.0L literature. Degas bottle passed pressure test holding near 15 PSI for 20 minutes! No oil in degas bottle that I can see.
Truck is stock. Is my egr cooler and oil cooler shot? Would a bad egr cooler or oil cooler cause this awful cold start? When I plug in the block heater, it starts NO PROBLEM, but still white smoke. Also, NO loss of power at any time.
View 6 Replies
I have a 2001 F450 7.3 chassis cab with just over 100k. I have a new problem... So far on two different occasions the service engine came on followed by a loss of power under a load and white smoke from the exhaust. Took it to the shop the first time, they determined it to be a dirty air filter, which seemed odd since it just happened all of a sudden. They changed air & fuel filter, problem gone- for two weeks..
View 8 Replies
I have a Tymar intake, magnaflow exhaust, a DP Tuner and I have Rosewood Diesel injectors.
I had a bad oil leak recently and it seemed to be coming from the turbo area so I changed all the o rings back there and deleted the EBPV system (I cut out the butterfly and welded the holes shut, cut the part of the pedestal that held the actuator because it looked like it was leaking and welded the oil holes in the pedestal that fed it. I left the actual EBPV sender in the pedestal and kept it connected to the harness)
After all that was done I checked the oil and it was low but still on the dipstick so I drove it to the local parts place to get some more oil, about 2 miles, because I wanted to check for leaks. It was not happy, ICP low code came up it was sputtering and jerking when stopped at a light. I got to the store and parked it, it took about 3 litres of oil and seemed to run pretty good after that.
But on the way home I noticed a bunch of white smoke, I figured maybe an injector was stuck. I started it a little later and no white smoke in the driveway so I thought maybe it had gotten lubed enough and had sorted itself out. That was a few days ago.
Today I started it and let it idle in the driveway for about 15 mins and no white smoke, I wanted to get it up to speed a little so I took it to do an errand that was about 10 miles away, lots of lights and a bit of highway. It would run fine while going at speed but as I would slow down for a light the ICP would go down to around 600psi and the white smoke would start, as sitting idling a huge cloud of white smoke would form (yes, I was that guy), once I could take off and get it running a bit harder it would go away again.
I am assuming that I have a stuck injector (or cracked), I have no oil in my degas bottle and it doesn't look like it is fuller than before. Seems like I may have used more fuel than I should have, but pretty hard to tell just from the fuel gauge.
I have tried a buzz test and they all sound the same, tried a Compression Contribution test, no codes from that.
How can I locate a stuck injector? If that's what it is?
View 7 Replies
I bought a 2004 power stroke with 100k miles, ran well for 15k miles then started having low power for first few minutes to no power, regular oil changes and fuel filters at 5k, checked FICM 48v KOEO , 48v cranking, new batteries just in case. Oil pressure when cranking at 50% of gauge , even crank cycle will jump when trying to fire, no loss of coolant, block heater working, it did start a few a few times and blew white smoke until warm then full power but the last 2 times I did get it to start it ran for less than 1 minute and died could not restart.
Fresh fuel additive in both fuel and oil for stickshion, have read hundreds of posts but not seeing similar problems no codes. With key cycle 120 amp draw on passengers battery for approx 25 seconds 48 amp on right battery glow plugs good due to the amp draw? So I think my FICM is good, good oil pressure cranking, the oil pump should be good, ICP good? Because of gauge coming up? Everything I read says black smoke for EGR soot issues. Not sure where to look.
View 14 Replies
it's now 1,500 miles away on the side of the road.White smoke, knocking and lost power. Truck has 133,000 reman engine installed at 46,000. Is it common for hydro locking to bend a rod? He sent a video and it def sounds like a rod and degas is empty.
View 9 Replies
I went out to the store today all was fine came back out and started driving got 2 miles down the road to a red light and the truck about stalled no power it doesn't smoke at idle but revved up it blows black and some white and the truck shakes. I am thinking its stiction or bad FICM????
View 13 Replies
I have an 07 6.0 with 400,000 miles. Has been a great truck with no major problems. Before I started the work I had 3 bad injectors, running rough and the oil/ coolant temp just outside of 15 degrees. So I tour her down and replaced head gaskets, installed arp studs,all new injectors,all new glow plugs and new oil cooler. Ran great for a couple days. Then when driving to work lost power on and off for a few miles then completely gone could only go 10 miles an hour. I checked codes and there was the under boost code witch has been on there for a while and I forget the other code but it was for the ipr valve so I replaced the valve and right after still the same but that code went away and the p0470 popped up. So I cleaned out the ep sensor tube and replaced the valve. After several miles she now runs great but now I'm getting a little puff of white smoke when I take off and not every time and mainly when I take off some what quick. All codes are gone expect the under boost. I have an egr delete already.
View 7 Replies
So I was on my way to work on a semi-chilly morning here in Colorado. Every day as usual, a little upset in the morning, a little white smoke and after a good warm up i'm on my way. About 10 minutes up the road while accelerating on the freeway, I hit I guess the perfect RPM range (2000-2500) when all of a sudden my CEL came on. Right as the CEL showed up, the engine introduce to me a new skip and lost a bit of power. About 5 more minutes up the road, the CEL went off and the skip went away, unless in idle. I made it to work a few minutes later and the skip in idle was apparent for sure. I turned her off and just couldn't get her to turn back on. The injectors are just not firing, no smoke at all, they don't even sound like they're trying to fire almost like no signal to the whole engine.
I replaced the CPS, the IPR and unplugged the ICP to test if she'd go. I opened the fuel bowl and watched it fill up. I checked the HPOP level, it was almost full, maybe a quarter (between half) inch from the top. No codes.
She ran great until this, outside of needing glow plugs. When I was trying to get her started it was 60ish outside so I don't think glow plugs is the issue. It sounds like the Injectors are not firing at all, whatsoever.
I will note that I had a few fuses blow out of no where that I replaced, a trail light, OBD fuse and one other in the under-dash box. I had her dyno'd a few weeks back and the tech said she made great power but sounded like she had a little issue recovering from the high RPMs but I figured my injectors are tired.
View 14 Replies
