Ford 6.0L Power Stroke Diesel :: No Buzz When Ignition Is On / No Crank And No OBD
Jul 9, 2015
2003 6.0 auto KR. Ign turns on, dash comes on like normal, windows & lights all work, vacumm pump works.. Thats it. Starter turns well if I hotwire it. Other then that she's dead. No buzz on inj when ign is on. OBD port has the power on blue/white wire but rest have none. Scanner says can't connect. Fuel pump doesn't run. Starter doesn't crank. All fuses have been checked.
Checked with test light on all the engine related fuses and they all light up. Relays have all been switched around. Tried another used PCM to test. Unplugged fan, ebp, map, maf. My brain is going on overload trying to get all these electrical issues fixed. I much prefer a HPO leak or inj going bad, that I know how to tackle. I hate electrical.
View 14 Replies
Advertisement
My nephew has a 2004 F350 that will crank but will not start. It will build oil pressure on the gauge. There is no injector buzz and no communication through OBD2 port. Is the PCM dead?
View 10 Replies
What this part it is? It sits over the alternator on the driver side and looks like a couple vacuum hoses plug into it. Mine is making a very loud buzzing noise.
View 8 Replies
While priming the high pressure oil system were using the starter jumper wire but after a while I wanted to watch the insight so I pulled the ficm relay but then it wouldn't crank with the key but before I pulled the ficm relay it would. Now it will start if you turn the key on and use the starter jumper wire but it still won't crank with the key. The truck has a viper alarm system I am thinking that might be causing the issue. How to trouble shoot that? Also I don't know if it is related but it has to crank for too long before it starts.
View 3 Replies
Turn ignition nooise, to get rid of the annoying buzzer. So I would like to do the same on my 2011 f250?
View 7 Replies
Stopped at the store, came out, started truck, ran for two seconds, shut off, hasn't run since,had no codes,or any other issues. I have checked all the fuses,breakers,main power supply off of passenger battery, still nothing. I have head and taillights, power points on dash, dome lights, chime for headlights. 79674 miles.
View 6 Replies
Ihave a 2008 E 350 6.0 , while driving i hit a small pothole no big deal the van stops running and coasts to the side of the road. get her towed. The dash lights show the PATS is engaged so it is no start no crank.
The 30 amp fuse PCM power relay is blown. when i replace it it blows as soon as i turn the key. im checking for wire chafing but so far have found none.
View 2 Replies
2003 crank no start, 196k bone stock truck egr still in truck and stock head bolts. Replaced the icp sensor and ipr sensor, both from ford. What happened is I got fuel then about 15 minutes afterwards my truck acted like it was going up a hill and was just losing power and shut itself off. ficm tested 48.5 volts all 8 injectors tested good and there is oil pressure. Had an egr fault code but I'm at a loss.....
View 7 Replies
The truck was running fine then I shut it off one day and it wouldn't start back up long powerful cranks but wouldn't start pulled the valve covers checked branch tubes and dummy plugs all looked good (not for sure though) replaced the icp and even tried unplugging it after the hot crank no start to see if that worked because that was the only a code I threw but alas it did not work.
I did a air test and closed the IPR valve via fancy tool and was getting some minor gurgling out of the oil filter resivuar and was guided to change the hpop being that was the beloved issue I couldn't get the j-tube out to inspect but everything else was clean as a whistle ... I was getting some air flow threw the oil filler cap and the air intake box on the driver's side valve cover but was told that is normal but not sure how normal when I replaced hpop it appears it stopped gurgling as much.
When I did the following air test but it started when cold but then it struggled but it did start then my batteries died out turns out I do have a bad negative connection I getting the batteries re charged gonna pick them up today and tighten that connection along with a new air filter via reading in the hanes manual that can sometimes cause a hot crank no start .
View 7 Replies
So, a year ago or so I had the truck die on me, it would start after cranking it a long time and cough/sputter for a few minutes with no power. I thought it seemed like a weak hpop or leaking oring, so I tore it down and put it all back together with a something or other hpop. Now I have a no crank no fuel pump condition, the injectors don't cycle when I turn the key on, I do get relays clicking, but no start, the yellow/blue wire gets the starter to turn over, but no fuel, so couldn't start if it wanted to... I am getting 120 ohms (like 122) on the dlc 6,14 and millivolts, basically nothing between 4 and 14...
I sent the ficm off to get rebuilt and they told me that it was already good (charged me anyway though, ah well...) I wiggled wires around and pulled my ficm plugs apart and pushed the wires in some, didn't seem to move any... What is next? There can't be that many things that cause all three, No Fuel Pump, No Crank and No Injector Buzz, can there?
View 14 Replies
My 2011 6.7L F250 Superduty died on interstate the other night. Picking up throttle pulling onto interstate when a message came on the dash "reducing engine power" and the truck died. It will crank but will not start. It will start on ether but dies when that runs out. Has the following codes... p1249 Wastegate control valve, p0087 fuel rail/system pressure too low, p1291 & p1292 injector high side short to ground or battery (bank 1 & 2), p2291 injector control pressure too low-engine cranking. The codes are telling me I don't have enough fuel pressure but scan tool says I have 4000 w/ key on and 6370 while cranking and I thought 5000 was the pressure needed.
View 9 Replies
I have a 2011 F250 w/6.7 Powerstroke. Love it. In September I came out of work, turn the key to on position...no glow plug indicator light, no high pitch whine of the fuel pump and most importantly, it won't crank. Gauges all light up, but no glow indicator, no fuel pump sound and no crank. Get towed to dealer. Next morning they try it, and it starts right up. They can't get it to fail. Sent me home with no trouble found.
A few weeks later, same condition in my garage. I had thought that maybe there was some sort of safety switch that perhaps thought it wasn't in park. I put in neutral, roll back about 6 inches, glow plugs light, fires right up. Now I think I'm on to something. In the last 2 weeks, it happened 2 more times, and both times I'm able to get it to light up by rolling a couple inches. Then, last night, same problem, but parked against a curb. Try to push up hill, but no luck.
Have to get towed to dealer again. Tow truck drops at dealer, and because I knew it would, I tried to start, and it worked. Dealer called me, says they can't get it to fail (again), but found one battery was "bad". I'm not really buying the battery story, but also understand the dealer having trouble figuring out what is wrong when nothing goes wrong for them.
View 14 Replies
I have a 2004 6liter. I parked one day two weeks ago and a went out last week to move it and I will only crank over. No fire No start!!!! Have new batteries. New fuel filter and have fuel coming in to the fuel bowl. I have gone over the harness, checked my fuses. I do not have a reader or scanner. Any recommendations. I want more than just a code scanner.
View 14 Replies
I was driving down the road and suddenly lost tons of acceleration power had to almost flour it to move at all so I pulled off the road to stop and check it out. After I stopped I couldn't get it to start again it would crank like it wanted to start but nothing. So I had I towed home and it sat for a little while and then I tried to crank again, and it started and idled like crap and when I pushed down on the gas pedal there was no reaction, rpms didn't go up or nothing but still would idle like crap.
Symptoms stayed the same for about a day and no I have a crank no start. So then I did what little I could do just to see if it was an easy fix I changed the ICP sensor, IPR sensor, and EGR valve needed to be replaced so I replaced that too. Headstuds and gaskets have been done as well by previous owner but not I think it might be an HPOP problem? I am unable to read codes at the moment as well just FYI. Could this be a fuel filter issue even tho the secondary housing fills with diesel?
View 1 Replies
So my 6.7 left me hanging the other day, went to start nothing. Towed it into town started. Went to start it couple days later nothing. Jump the plug by right battery starter turns. When key is turned to run no glow plug light, no fuel pump prime. Tested ignition switch good. Tried 2 new Batteries nothing. got power on fuse 52, continuity from fuse 52 to pcm connector. Fuse 49 and 50 also have power. Took all 3 connectors at pcm out and blowed air through and sprayed W.D nothing. Even tried with connector on transmission. Scan tool will not communicate with pcm.
Codes after cleared:
instrument cluster:
uo100 lost communication to pcm
u300a-64 ignition switch...
transmission:
u0294 lost communication with pcm
Body control module:
u0100-87 lost communication with pcm
B10f1-14 key in switch short to ground or open
View 7 Replies
I'm having a long crank cold start issue. It takes about 2 five second cranks before the truck will start up. It just started acting this way yesterday before I fired it up to go to school. After its warm it fires up no problem the rest of the day, just takes a bump of the key.
I don't think it's the GP system as this truck has started at -20 to -25C all winter long unplugged with no issues. From my reading some sources say that it could be a HPOP leak, maybe dummy plugs?
Is there any way for me to do some more diagnosing - places to look or test for? There are no stored codes other than an EGR code due to the delete. Truck is completely stock with atlas 40.
View 6 Replies
ok, so after all the work done (headgaskets, head bolts, egr valve, ipr valve, egr cooler, oil cooler, blue spring kit, new ficm injector harness connectors), this is what I'm left with on start up. I am now getting no SYNC -0
I had ficm sync before i changed the connectors on the injector harness (last thing i did besides blue spring kit). Has this motor turn this way? And my glow plug light now comes on during and post crank along with a weird fuel light with 3 teardrops I've never seen before. I need to check this out.
48.0 ficm KOEO, 48.3 crank
IPC 3 KOEO, 1100 crank
IPR 14.1 KOEO, 46 crank
IPC volt .23 KOEO, 1.23 crank
Passed bubble test
View 14 Replies
I have a 2004 f250 Super Duty crew cab. it was in a front end accident.I will able to drive it over 600 miles home and it ran for a few weeks until one day at the gas station I tried to start it and it backfired.ever since then it hasn't been able to fire up at all. It will not crank a full turn at all. I was told to start with pulling glow plugs and if there was oil on them, then either my crank shaft is siezed up or I need new head gaskets. I have rebuilt many gas motors over the years, but this will be my first diesel. My question is, at what point should i be looking to buy a new motor?
View 9 Replies
2003 6.0, all stock. Crank, no start with an occasional sputter when it actually shows FICM SYNC = YES.
It had the following relevant DTCs when I scanned it:
P0261, P0270, P0276 and P0279 - Cylinders 1, 4, 6 and 7 - Injector circuit low
P132B - Turbocharger/Supercharger boost control A performance
P2614 - CMP Open circuit
P2617 - CKP Open circuit
CMP/CKP SYNC transitions to and maintains YES while cranking, however FICM SYNC transitions back and forth between YES and NO while cranking. When it transitions to YES, a cylinder or two will fire when FIPW comes up, but FICM SYNC almost immediately transitions back to NO.
Based solely on the scan tool results, Cranking shows IPR DC at about 50%, ICP PSI ~1500, ICP V ~2.0. These are stable and steady. FICM main power is at 49.5v and drops to 49.0 when it fires the occasional injector while cranking. RPM reads above 150 while cranking.
I'm thinking that since CMP/CKP SYNC stays YES and is stable and RPM reading is consistent, the CMP & CKP sensors and circuits are most likely good. I'm thinking with the codes for injectors 1, 4, 6 and 7 it probably points more toward a FICM issue.
Another thing that may or may not be relevant is the pre-cycle clatter sounds off to me. With an ambient temp of about 70F, the pre-cycle seems to repeat 3 times. The second and third cycles sound worse than the first. This is in the video below.
I work on far more 7.3s than I do 6.0s, so I'm looking for anything I may have overlooked, a second/third/fourth opinion, or if there's a flaw in my logic for someone to point it out.
6.0 No Start - YouTube
View 14 Replies
Brother in law company 6.0 died on him in his driveway after a night of plowing
It stalled out, his boss sent out a "tech" and he said it doesn't have "nearly enough" oil pressure
Now I want to further diagnose the truck myself with my scan gauge II but haven't used it for that......yet......
What should I check for IPR pressure psi or %?
I know I can get ICP pressure in PSI on my SCT x4 not sure about the Scan Gauge......
I assume a blown IPR or failed STC fitting......
Truck is a 2005..... I can figure out the scan gauge I just need to know what to look for for an idea of a blown IPR or STC or ICP.
View 14 Replies
05 6.0 will only start if I cycle the glow plugs, crank 3 seconds shut off glow again then it starts immediately. If I try to glow 2 cycles with out cranking it won't start either. When he truck is hot it seams to start easier. I have new batteries new alternator running 5-40 synth. New glow plug control module. It does it hot or cold weather.
View 7 Replies
