Ford 6.0L Power Stroke Diesel :: No Boost - P2290 Code For Low Injection Control Pressure
Sep 10, 2015
My 05 excursion died on me a couple weeks ago. First it threw a p2290 code for low injection control pressure. It did this a few months ago and had no problems. Cleared code and did not come back until now. So I cleared the code. Drove a few more miles and lost all boost pressure. Still fires up and runs. It does run a bit rough but only a little bit.
I replaced the oil cooler, did egr delete, and put an IPR remote oil cooler and full flow coolant filter on it few months ago. Since it died i pulled the ipr valve and it looked good. I put a new screen o-rings, and wiring pigtail on it since it was out. Put back together and still no boost. I really did not figure that would fix the boost issue but i wanted to make sure the screen was not clogged or torn.
Truck will fire up cold and warm with no problem and run. The hose from the map sensor to manifold is good and i put new clamps on it.
2005 6.0 with 95,000 miles.
ICP duty cycle = 0.29
map kpa = 102
Injection control pressure = 5.91 MPA
View 14 Replies
Advertisement
I just did a bunch of work on my 6.0. Here's a list- head gaskets, arp studs, new heads, 2 new injectors, updated stand pipes and dummy plugs, water pump, and all new injector o-rings. After messing around with a bent pushrod, cylinder 5 code and and replacing injectors the truck runs excellent. After driving it a bit I get a code "P2290 injector control pressure too low". The truck runs great with no low power, stalls, or hard start cold or hot. I do puff black smoke but that's because of the sct tuner on performance tune.
View 8 Replies
2004 Excursion 6.0L .... Recently after a 200 mile trip through the mountains running good, I get home and the next day it idles down the driveway at a high idle and after a few minutes seems to run better but within 5 miles the CEL comes on and throws P2287 - intermittent injection pressure control circuit. I cleared the code, ran around town again and the light came on again same code. I'm getting appropriate ICP-voltage and pressure readings. I took it home sat overnight and thought I would pull the ICP sensor.
I replaced the ICP sensor less than 6 months/5,000 miles ago. I also changed out the main engine harness at the same time. I looked at ICP sensor and it looks clean. Started the truck and tried the scientific wiggle test while running and monitoring ICP-voltage. Started at the sensor bending and wiggling back to FICM. No fluctuation in voltage. Ran the truck around town, 20 miles and no light. Yesterday we made the same 200 mile trip over the mountains, seemed to run strong. In town this morning within 5 miles the CEL is back on and the only code is P2287.
My Ford powertrain diagnostics manual doesn't have the P2287 code in it for troubleshooting. Should I go after the FICM, and how do U test that if so? I'm currently that 200 mile drive from home and don't want to damage anything more.
View 8 Replies
As the title says I am suddenly having a long crank when starting and low oil pressure when when warm (above approximately 100 degrees). IPR goes to 85% when cranking. Stored codes were P2290 and P2291. Other symptoms are low power and what sounds like a power steering pump with low oil whine and low power. (It is not power steering related however, I checked.) I pulled the oil filter and cranked engine and filter bowl filled in less than 10 seconds.
Oil did have a fair bit of air bubbles. Oil has 5000 miles and is Motorcraft 10w30 diesel. I have not added any since the last change. I do not have the new style pump so it's not the STC fitting. What my issue is? I do have AE if any other info is required. Particulars are in sig. The searches I have done combined with the mileage I have lead me to either the low pressure pump is failing, or the high pressure pump has lost the ball bearing out of the side.
View 6 Replies
Long story behind it but finally got my scanner working right and checked the suggested systems for p2290.
IPR was 77+ on start up dropped to around 31 at idle
FMP is in the 46.5 to 47.5 range
SYC was at 1 and occasionally at 1.5
ICP was at 550-650 during startup and quickly ramped up to 1150 then settled into around 850 at idle.
The only thing that I'm not sure of is the IPR being 31 at idle, is that what it should be. The others I think are within normal operating parameters.
The truck starts but has no power. Can barely go up a slight hill on my street. Seems like it's going to be fine but as soon as I apply a little gas it just falls off.
View 13 Replies
I have a 2007 F250 6.0 L with 116000 miles. I have never done any modifications or changed anything on the truck. Now that the weather is starting to warm up I've noticed that once the truck is at operating temperature it starts to chug and sometimes even die while driving and while its doing this the truck has no power. It does not seem to do it when its cold. Here is a picture of my gauges KOEO operating temp at idle...
View 4 Replies
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 Replies
Having trouble with this code. Replaced stock air filter with aFe filter 10,000 miles ago. 20,000 on truck. Threw code sunday dealer replaced filter with stock. said code may come back. which it did 5 miles later.
Edge CTS says max boost is at 22 psi. Is this something i will live with or indication of something else?
View 6 Replies
Earlier this week, I had the p1260 pop up. Then while driving to the beach, I had the p2290 pop up. I do not actually have a check engine light on, but used my torque app to find the codes. I have found a oil leak on the driver side coming from somewhere. I have a mishimoto thermostat coming in next week. I will try to collect parts needed for this repair. From my understanding, it's a hpop leak and the adrenaline and stc fitting should be my next move.
View 13 Replies
I'm having a little trouble with my 05 Excursion 6.0L .... We took off camping the other day pulling our 30' camper and the engine light came on pretty much as soon as we hit the highways. I checked my Dash boss and it came up as P0299 under boost condition. The truck never skipped a beat. The boost gauge never dropped and it seemed to have lots of power. Actually I've noticed too much boost while pulling. It's climbed up to 36psi before and was still climbing when I backed off the throttle. I'm thinking the turbo is fine but not sure what to check next.
View 7 Replies
P0237 code. The truck is a 2003 f250 with an edge evo . The truck will run great then throws this code and won't build boost of over 11 psi. Now it even drops it right off to 0. I replaced the map sensor a month ago and doesn't seem to have fixed anything.
View 2 Replies
Boost gauge is pegged and have no turbo don't know if the code has anything to do with the problem or not its a po6a7...
View 6 Replies
Last night when I was towing my son's Ranger home - somebody stole all his gas & he thought the fuel pump quit - heard a pop and the truck started running like crap. Thought I had blown the CAC boot loose but that wasn't the case. As it turns out, the tube for the EBP sensor came off from the manifold.
I had taken it loose about a year ago to clean it out. I guess I didn't tighten it well enough. Truck blew black smoke, lost boost, and filled the cab with exhaust fumes. Easy enough fix, kind of hard to diagnose because that's not expected. Just throwing it out the for somebody's future search.
View 1 Replies
My truck threw a CEL after the first start today. The CTS reports it twice. I noticed it about two minutes after start.
P02E1 - Diesel Intake Air Flow Control Performance
The air box gauge is green and it doesn't reset when I push it so that appears to be fine.
The one thing I can easily notice is the sound of the turbo. Typically when I stop and park, the turbo spools up, then down, then spools again and gives a sigh of relief and it's then silent. It's not doing that currently.
Now, I can hear it constantly when parked and it spools down after I turn off the engine, even two minutes later. That is not normal for my truck when I wait for the above to finish its routine. When I start the truck, the turbo immediately spools to where I can hear it which is also not normal, as if it's building 0.5 psi. I realize that's funny to say on a turbo diesel but I know the sounds of my truck. The EGT's are fine, EOT, ECT, TFT are fine and I can build boost when driving without issue. I took the drive to work easy this morning so the highest I noticed was 10 psi.
I restarted the truck after a 20 minute drive to the office and it didn't clear the CEL. The CTS squawked four times when it woke up the second time but it didn't show me which PID it was upset about.
I'm thinking this has nothing to do with the CAI and this is something downstream of there. EGR related? I haven't opened the air box yet, at work and in dress clothes so that'll need to wait. My past four or five regenerations all started between 1.94 and 1.97 soot gpl. That is also not normal and is something I have been keeping my eyes on. Currently the DPF is at 2.10 so it has made it further. Normal behavior (post emissions flash) is above 2.54 soot gpl for an AR.
View 4 Replies
I have this sensor unplugged. Is there a way to defeat this sensor so I don't pull this code?
View 3 Replies
I have a 2011 F350 6.7 cclb 4wd dually. 212k ... I have the dtc p0284. The run good at idle and driving. I use it to pull a 40ft enclosed trailer. I have noticed that the boost gauge peaks at the half way mark and slowly drops half way down. I can feel my truck lose power when that happens. I also noticed that it runs alot better at night than the day. I have not modified anything except a s&b cold air intake. I have the #8injector replaced.
View 2 Replies
I have a 2004 6.0 with 75000 miles on it. My truck is throwing a P0470 code pointing at the exhaust pressure sensor. my question is do I need this sensor or can i bypass it? When I look up the part it only shows 2005 and up.
View 6 Replies
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
View 14 Replies
My truck threw a P2073 code. Its Manifold Absolute Pressure/Mass Air Flow - Throttle Position Correlation at Idle. I do have aftermarket intake. It threw this code 2 weeks after install. Does this mean my mass air flow sensor is going to fail soon?
View 14 Replies
Okay, so I have a 14' 6.7L, about 18,438 miles on it and the check engine light came on when I was at the gas station ready to leave, and so I took a field trip to auto zone and they scanned the CEL and it came back as P20BA - Reductant Heater 'A' Control Circuit Performance and they said I need to change out the pump assembly so I took it to the dealership and they cleared the code which worked for awhile, about 4 months ago the light came back on and I'm wonder if I should get the pump/heater changed out or get it deleted? The warranty is going to end in august this year..... It's been fine no issues with the truck, even tho I drive with the CEL on and just wondering what I should do? The CEL has been on for almost 5 months.
View 4 Replies
I have a 2012 6.7 with a Spartan tuner. Threw this code a few months ago. Reset everything, trucks runs great, no issues. Never had this code come up again. I've looked it up and it says, "Internal Control Module Torque Performance". I'm just not sure what this means.
View 2 Replies
