Ford 6.0L Power Stroke Diesel :: Missing When On Interstate Just Cruising Along With RPMs Below 1900
Jun 14, 2015
I get what I can only describe as a "missing" when Im on the interstate just cruising along with rpms below say around 1900. That seems to be when I have noticed it. It is not very frequent but often enough to not let me forget about it. Happens when I'm towing it seems more than when not. Seems the rpms have to be below 18-1900 and in 5th speed. You can just feel the truck ever so slightly missing like in the old days of points and distributor caps. No tunes
View 7 Replies
Advertisement
While I'm cursing at highway speed everything is fine. But when u punch it it pass someone it's like I actually slow down, same from a red light. I've got a livewire programmer in it and this problem is somewhat new. It just seems to keep getting worse, I was going up a hill on the interstate this morning and at 2800 rpms I was actually slowing down. I'm not sure if the fuel pump is going out or if the transmission is slipping or what.
View 7 Replies
I have a 2012 F-250 6.7L w/8K miles. I have been struggling with this issue for 6 mo. The engine feels like its missing at low RPM. I would equate it to the feeling of a bad coil pack in a gas engine. The boost indicator drops to 0 for a split second then recovers. The dealer says they can't find the issue but went ahead and replaced the turbo. After the turbo replacement It got worse. This is an intermittent problem with no codes.
View 14 Replies
I have a 2012 F350 I keep the hubs in auto all the time. In the winter I just flip the switch to 4 high when I hit snow conditions. I know to shift in or out I need to be below 55mph. How fast can I safely drive in 4 high on the interstate? I drive hundreds of miles at a time in the winter. Some times if the roads clear I will cruise at 70-80mph. This is a question of mechanical safety on truck components not driving safety.
View 13 Replies
2013 CCLB, 33,500 miles, stock emissions
While towing a 9000 pound trailer at interstate speeds (75 to 80 in Wyoming), when pulling a hill, the truck downshifts to 4th gear, boost is about 18psi, eng and transmission temps in the 230F range, EGTs around 500C or 935F. RPM increases normally to 3000 then the turbo gets very loud and boost drops to about 10psi. The truck shifts to 5th gear, noise decreases but is still present, shifts to 6th and noise goes to normal after a couple seconds and boost builds normally.
This just started today. I have about 8000 miles towing this trailer and never had this before. I have about 350 miles until I'm home so I'm headed back out. Will play around with manual mode and see what it does. I also took a video of the gauges while this happens. Audio is difficult to discern. I will try to get better audio and post when I get home.
View 5 Replies
I've been getting a surge or revs when getting up to cruising speed before it drops into overdrive or or a constant speed. Happens around 1800-2200 rpm before up shifting to the next gear. More noticeable if under a load or going up a grade when it will hold gear longer before shifting. Only thing I can think of that would be related is the truck does lack some power on a cold start for the first couple miles before getting up to temp. I've cleaned the ebp sensor and it appears to be working correctly, reading within .1-.2 of BAR/MAP key one engine off. VGT solenoid is clean but have no real way to tell if it's working correctly. Other values icp/ipr temps fluid levels appear to be correct. Just changed the oil and it continues, changed the transmission oil and filter about 3000 miles ago. I've had this going on for about 1000. Started about the same time I changed tunes to PHP. They haven't been able to find anything in the tuning yet that could be causing this or if it is just making it show up now.
View 14 Replies
Still chasing a surge for some time while cold, mainly. While hot and cruising 65 mph the turbo still surges faintly.. but today was a different story, very fast and high surging from the turbo only, while on overdrive as usual. It calmed down as i dropped the boost a bit but it was quick swings of about 3-5 psi which is quite bad for what it had been doing which was manageable.
Short of taking off the turbo, I took out the VGT solenoid and it had some oil burnt on the end, cleaned that up and pushed the plunger in all the way a few times and it 'seemed' to have worked greatly, until today.
I pulled some other numbers;
KOEO
Map 13.7
EBP 14.1
Baro 28.2
Cold Idle
Map 14.0
EBP 16.5
Baro 28.2
When cold, mainly below 130F the RPM gauge itself will surge or hesitate around 1700-2000 RPM. Any higher or lower it will be smoother I suppose....
View 14 Replies
OK here's the deal. Cruising down the road at 55 mph, I felt a pop and then the engine just stopped running.
When I tried to start it up, no oil pressure. It appears that the IPR valve may have failed, but I'm curious if the pop was a catastrophic IPR failure or an indication of something else?
View 7 Replies
Just a quick question but is it normal for the ICP voltage (ICV) to jump around a lot at idle or while cruising or accelerating? Started watching this pid and not sure what's normal and what's not.
View 13 Replies
I ran out and test drove a new to me 2001 F350 7.3L tonight. Everything seemed good, until I got back from the test drive. I pulled in and was sitting there with it idling. It seemed to idle fine, then a very small miss and very small shimmy then idle fine again; then another small miss and another shimmy. It continued like clockwork. Every time it seemed to miss and shimmy, the RPM would drop just a little, but not much. Does an ICP sensor sound like the problem, or maybe something more serious? 2001 F350 7.3L with 235,733 miles new trans, turbo replaced at 150,000 something miles. No blow by. Idled fine before driving, also drove fine. It doesn't seem to surge when idling, just kind stalls and shimmys for a split second then idles fine for a few seconds.
View 1 Replies
,the symptom that I'm wondering about is that when the truck is cruising at different high speeds like 65 or 75 it starts to jerk/jolt, if I accelerate it goes away, or if I let off the accelerator.
Once I settle on a different cruising speed it does it again. There is no smoke out the exhaust pipe, it does not loses any power, I look at the RPM's and they don't move when the jerking/jolting starts. Truck runs fine except for this issue.
I do get the P0404 and P0405 codes which are for the EGR valve and the sensor. By the way **is there an EGR SENSOR** anywhere on this engine, I seen some posts where people refer to it as the EBP Sensor, is this correct? I cleaned the EGR valve, but it did not do anything to fix the issue. I'm thinking I damaged the valve when I cleaned it, but I would like to verify that this symptom could be the EGR valve before I buy a new one.
View 6 Replies
I have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
View 3 Replies
To start off. I have a 2004 F350 with the 6.0 in it which just had a top end rebuild done on it due to the head gasket blowing on it. During the rebuild the EGR cooler was also deleted, ARP head studs, Heads were milled down to make them flat (shop said they had to take 9 thousands off to do so), new up pipes installed, new back pressure sensor installed due to the plug head snapping off, new glow plugs, new glow plug rail harness, oil rail rebuilt due to bad o-rings on the ball tubes, injectors were installed with all new seals and had polished the spool valves hoping to avoid stiction (however its spelled can never remember), and lastly the EGR was deleted electronically with tuner. Also had to get 2 new batteries as they were stone dead and would not take a charge. And had to get a new alternator due to low output. Not sure if the alternator killed the batteries or the batteries killed the alternator either way it needed replaced to.. Unfortunately after i got that fixed i had to get a new starter as it died 3 days later.
Ever since its gone back together Ive had a consistent intermittent miss with the truck. Ive searched every article i can find but seems most complain about misses when cold. Mine is the exact opposite as it only does it once the engines up to normal operating temp. It accelerates hard and fast like it has no issues. While its cold it doesnt miss at all. Once its warmed up sometimes while cruising it will feel like its missing on every cylinder or better description would be as if your driving on a cobble stone road.. If you mash the pedal for a couple seconds till it kicks down and raises the rpms it stops.. Its most prevalent at idle though.. You can literally hear the difference in the engine when it starts missing. Truck will shake as if its got a large lopey cam. Odd part while sitting at idle it will cycle back and forth between running smooth and missing. But same with at cruise as soon as you get on the throttle it goes away. If its doing it while sitting idle at a light, it will take a couple seconds once your on the throttle for it to smooths out. But always does.
Ive tested the Ficm hot and cold, KOEoff and KOEOn.. getting a steady 48v from the main board.. Scan gauge says the Logic boards reading steady 13v... Also from the scan gauge it says my ICP pressure is in the 640 range at idle (full throttle highest ive seen is 3600psi so dont think its a pressure leak) and volts bounce between .80-.90.. but oddly once it starts missing the ICP pressure jumps up 20 psi.. IPR at idle reads 23.5-25.5.. at cruise its up around 45ish.. fuel pressures said to 70 psi.. which its usually around that most times, cruising itll be around 66psi. I had 3 injectors replaced not this past spring but the year before (ironically same symptoms).. Injectors 5,7,8 were replaced then.. ICP sensor was also replaced at the same time as it split and shorted out the connector which was the initial reason i took it in that time since it was dumping the oil on the ground.
I dont have any way to perform a cylinder contribution test and after spending 6K on a rebuild I really cant afford to take it in to have someone else do it. A local guy was able to scan the truck for me but he couldn't do the contribution test either but was able to buzz test them. Everything passed there but we also found some hidden fault codes my code readers did not find. The ones we found hidden said that injectors 2, 4, and 7(again??) are reading low contribution. Of what I've read 2 & 4 sit on either side of 7 in the firing order so have wondered if they're not pulling down 7's results.
I really cant afford to replace the injectors till near the end of next month. Is there anything else I can look at that might actually possibly be causing false readings or intermittent misses only when warm.
View 14 Replies
Truck is bucking and missing every 10 seconds or so and will stall when taking off in drive sometimes but fires right back up? I got a lot of codes in the torque pro app but some are in grey. Not sure what that means. EGR has been deleted so that's why I got those codes. I was cleaning the back of the truck the other day and found a can of quick start . Guess that might be why i got codes for glow plugs also. I'm gonna post up pic of my codes and numbers of truck running at idle in drive. So far I see I got a code for cylinder 6 contribution? It's in grey tho whatever that means.
View 8 Replies
just overhauled my 6.0. run great for about 3 days now runs really rough when cold. new heads injectors rings pistons ficm fuel pump icp sensor ipr valve fuel pressure is good. Engine rolls smoothly when cold also.
View 14 Replies
I have an 11 F350 6.7. It has just under 200K miles on it. The other day I was driving home, about 100 miles, and my truck's temp spiked. Not like a little spike, but jumped to the 3/4 mark (if there was one) then slowly kept rising to to the overheat mark. I pulled off onto the hard shoulder waited an hour or so to let it cool down, then finished the drive home. All the way home my temp gauge seemed like it was on some sort of drug. It would jump a needle width when I would have to accelerate, then slowly cool to normal after I got up to cruising speed.
Up until this point this truck has been exceedingly reliable. I pull a 13k 5th wheel once a month and drive about 40k-ish miles a year. I also had to refill my degas bottle up to the fill line. Took 2 gallons of Ford VC-3-B Coolant and water mix. After a short run to verify the problem, it took another 1/4 to 1/2 gallon of mix. But, no overheating. No signs of leaks anywhere. Just a strong scent of coolant on shutdown outside the truck. Pressure tested the cap, I don't have a way of testing the system pressure.
Data from Autoenginuity:
Engine Oil temp 195-202 Degrees
Engine Coolant #1: 188.2-199.5 Degrees.
Engine Coolant #2: 125.5-129.9 Degrees.
I have the full CSV file.
View 6 Replies
I have a 2006 F250 6.0L. Just had a used motor with 108k miles put in. Had the motor studded, fire ringed, new injectors, new glow plugs, new radiator fluid filter system installed, had egr delete done, ficm board replaced, fuel pump replaced, a few other small items replaced as well. The problem I'm having is the truck runs like it has a miss until it warms up.
After that, it runs fine. It takes about 10/15 miles of driving before it runs like it should. Letting it run in the driveway for 10/15 minutes to warm up doesn't make a difference. When the truck starts, it lopes at an idle for about 5 mins before turbo kicks in & starts whistling. When I start driving it shakes & feels like it has no power until it warms up. Then you'd never know anything was wrong. Put way too much $ into the truck so far and can't keep going.
View 7 Replies
I have 1 bad injector well it's missing when it's cold and two others that are "weak" I'm wondering what kind of job it would be to do by myself?
View 14 Replies
I have a 2003 Excursion with the 6.0 power stroke. I recently had a few codes, cylinder 2, 3, and 8 contribution/balance fault. I asked a buddy of mine, and he said I needed new injectors. I replaced them all, properly torqued everything down, and got it running. She ran for 20 minutes before it started missing again. I shut it down, and since then it hasn't started. That was two Sundays ago. Since then, I've replaced the ficm, all fuses related to the ficm and fuel pump, and even went in and checked all the connectors. Everything is in place, but it still won't run.
View 14 Replies
Bought a 2004 f350 lariat last fall. Overhead console was missing. Finally got around to replacing the display. Temp, compass works fine, but mileage and distance to empty are way off. Display typically shows 13.5mpg but when manually calculating am usually closer to 17. Distance to empty is way off as well. I did some research but didn't find much on how to recalibrate it. No difference with or without tunes.
View 8 Replies
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
View 14 Replies
