Ford 6.0L Power Stroke Diesel :: Loss Of Power When Driving Or Leaving From A Stopped Position
Jul 12, 2011
I have searched and the only thing close is bad sensor for water in fuel light but it does not say they lost power. When driving or leaving from a stopped position, if I put any extra load on engine by pressing on accelerator pedal fast the water in fuel light comes on and the glow plug light comes on and the truck loses all power. Not 12V power just engine power. I have to let off the pedal and the lights go out and I have power again. Until I press the pedal hard again and it does it again. I have drained the filters and replaced them and still the same.
View 14 Replies
Advertisement
So loss power on take off and then stopped at store quick shut it down. Came out of store ten minutes later no start just turns over and over. I replaced IPR last year the one on passenger side near frame if that's correct and perhaps this is the ICP near back of engine?
View 14 Replies
Occasionally when I'm driving, I'll accelerate and get a brief loss of power, then it'll pick back up, followed by a puff of white/blue smoke. This usually happens when the oil is over 120*, but not quite to full operating temps. It doesn't happen every time either. Only 3 times in the past week. Otherwise, there is a very faint haze of white smoke that seems to be constant. It is very difficult to see unless against a dark background. Oil level is good, I check it once a week, no rising or lowering levels.
I pulled the EGR yesterday, all good, although a tad dirty. Cleaned up no problem. Haven't had a chance to do a bubble test yet. There are some DTCs, but I can't remember off the top of my head what they were. I'm about to go clean the inside of the truck, so I will pull those and update in a few minutes.
Truck has about 148,500 miles.
Torque Pro lists these codes: C1145, P0299, P0677
View 7 Replies
I have an 07 6.0 with 400,000 miles. Has been a great truck with no major problems. Before I started the work I had 3 bad injectors, running rough and the oil/ coolant temp just outside of 15 degrees. So I tour her down and replaced head gaskets, installed arp studs,all new injectors,all new glow plugs and new oil cooler. Ran great for a couple days. Then when driving to work lost power on and off for a few miles then completely gone could only go 10 miles an hour. I checked codes and there was the under boost code witch has been on there for a while and I forget the other code but it was for the ipr valve so I replaced the valve and right after still the same but that code went away and the p0470 popped up. So I cleaned out the ep sensor tube and replaced the valve. After several miles she now runs great but now I'm getting a little puff of white smoke when I take off and not every time and mainly when I take off some what quick. All codes are gone expect the under boost. I have an egr delete already.
View 7 Replies
Just replace the b solenoid in my transmission last night; everything running good now, but for some reason it started doing this weird thing where if I come to a complete stop at a red light, then ease into the throttle, it will start surging,bucking. If I give it a little more gas on the pedal it will smooth out though. It only does it if u ease into the throttle after a complete or near complete stop. What's going on?
View 7 Replies
Turbo def needed rebuilt, unison ring was worn out. Ton of carbon build up also. Was leaking oil too. Rebuilt it, good to go now.
Egr cooler wasn't leaking and was plugged on the one end. Got the IPR kit installed, nice kit. Re sealed the oil cooler at the same time. CCV re route done.
Here is the kicker. It still SMOKES!!! Only when leaving a stop light. There was quite a bit of oil in the turbo piping. I cleaned that all out. Could it still be oil in the intercooler and it just needs times to get blown out? Or??? I did a power balance test, cylinder contribution test, injector kill test, and etc all passed.
Maybe hook the boat up pull a 6% grade and get all that blown out?
View 5 Replies
I have a 2006 f350 with 75k on it, has a mild sct towing tune, and 4' turbo abck dual exhaust. It recently started blowing whiteish smoke, so i did an EGR cooler and valve delete kit, and it stoppe dsmoking for a while.. coinsidence?
It has recently started again, at idle there is no smoke, and taking off slow from a stop, it doesnt ALWAYS smoke. but leaving a dead stop, if i get right into it, it billows whiteish smoke, and if im cruising, romp on it, let off it, then get on it again it will smoke.
Ive been told fuel pressure, injectors, turbo seal etc. when i had the down pipe off, no sticky black residue was present, so im counting out turbo seal (for now). I purchased the blue spring upgrade for fuel pressure, because i was told its not getting the right amount of fuel, once i get that ill throw it in and see if it fixes it.
whats yall's opinion? is it worth have it checked for a failed injector? as i said, no EGR in the truck, no loss of coolant either, oil is clean. It does seem a little sluggish at times off the line now as well.
View 11 Replies
I have been getting about a 1-2 second power loss while driving. happened last friday when at a stop light, pressed the pedal and started to go then it dropped out for a second or two and then caught right back up. only cut out twice in 10 minutes then ran fine for another week. This friday oddly enough , it happened again while driving down the road. happened about 5 different times in 10 minutes, then back to normal. I replaced the passenger uvch with dorman, but not driver side a couple of months ago . Does this sound like the other uvch, or tps?
View 6 Replies
My issue can be while driving with cruise on, or accelerating, the truck just losses power, then recovers. At idle, the rpm can, but not always, fluctuate.
There is no "misfire" when it happens, but it just falls on its face. I have NO diagnostic tools, and my injectors are not stock, so I am unable to unplug my DP.
My thoughts are to unplug the ICP and give that a shot? Meanwhile, I will put in a order for a elm327
View 14 Replies
Been a while... Problem today while towing... I was in some hilly areas but nothing too .. I was pulling an unloaded trailer and experienced a significant loss of power and overheating. Engine started getting hot (almost to red) and then the transmission came up in temp. Made it to a rest area and all cooled down within 2 to 5 mins... but the strange thing about the power uphill is that it is happening at slow speeds as well... boost seems normal. Recently did the injector cups, so the thermostat is new (motorcraft), coolant is new, and put new o-rings on injectors.
View 14 Replies
Today I was riding along and all of a sudden I noticed a loss of power. I look in the rear view mirror and get into the pedal and a lot of black smoke. When I get to where I'm going and stop I noticed the idol was a little loopy. I never saw a check engine light. I have the Edge insight. I had two codes. P1000 OBD System readiness test not complete. P2290 ICP TO LOW.
When I would reset the codes the P1000 came back instantly every time. I parked the truck for about an hour. When I started it back up everything was normal. The power was back and no smoke. This happened two more times throughout the day. I have heard people describe a sticking EGR Valve causing these symptoms. Is that where I should start looking or is the ICP the culprit or something else?
View 7 Replies
I have a 2004 F250 6.0 DuperDuty with about 170,000 miles on it, so far no major break-downs, just a starter and a blinker relay, but now I have a problem.
When I start now, the truck starts fine and it sounds fine, but it has almost no power even if I floor the gas peddle, there is a delay of like 2-3 seconds and then responds slowly, like some tractor. Eventually it starts to move slowly, and after it warms up (after a few minutes), the gas peddle responds more normal.
Also - at about 45mpg, at lower RPMs about 1250, the engine starts to shake (weird), it doesn't do it at idle about 850 RPM, or when I get it up to about 1800RPM+, but at about that 1250 RPM it does do it, luckily I driver locally for a few miles.
What could this be ? What exactly happens when I press on the gas peddle, what systems are involved and in which order?
View 14 Replies
My uncle was pulling his fiver to the beach yesterday with his 2011 f-350 6.7. He lost power, the truck got very loud, and there is a very strong stale kerosene smell in the cab. Strong enough to require the windows be down for ventilation. He was able to limp on into the campground and has an appointment with the dealership Monday. The truck has 19,000 miles and is still covered under the extended warranty.
View 8 Replies
I've got a 2004 F250, 6.0, with 150k miles. I was pulling a motorcycle trailer uphill in the mountains when suddenly I couldn't go over 10 to 15 mph. All the gauges read good but it just couldn't get any power.
Got to the top and checked over everything. Didn't see any issues. Drove it home (200 miles) the next day. It drove okay on highway but it felt like the turbo wasn't coming on. Coolant was low and EGR was gunked up but only slightly wet. From what I read, it sounds like EGR cooler is failing but would that cause the turbo not to come on or feel like that loss of power? Reading another thread, I thought it might be the fuel pickup but I dropped the tank and the sending unit looked very good.
I'm ready to throw on a bulletproof egr cooler, oil cooler and rebuild the turbo if necessary but hate to get to the end and find out none of that worked.
View 5 Replies
I have a 2004 Super Duty with a 6.0 diesel. Recently the windshield washer seems to have lost some of it's spray power. It still sprays, just not very hard. I know it's not frozen, as it started this before it got cold.
View 3 Replies
Truck = 2011 F250 150,000 miles, no modifications, stock.
Truck lost power yesterday, no boost, and no codes. When driving on Friday, I started moving from a red light. The truck seemed very sluggish. Then I noticed it downshift going up a small hill that it never downshifts before. I looked, and noticed the turbo gauge at 0, no boost. I pulled over, turned it off, then restarted it, but still no boost, and the truck is very under-powered. I looked over the area, and do not notice any leaks, also no leaks underneath. I hooked up my OBD reader, and no codes., the boost gauge is on zero, and the truck has lost significant power. I no longer hear the turbo spooling.
I have spent the past several hours searching sites and forums (Started with FTE ), and it seems that most believe a restart of the truck has solved it for them. However, this is not the case for me, a restart, even after letting it sit overnight did not resolve the issue.
I did see one reference that replacing a NOX sensor solved their problem. This brings up some interesting truck history. Back in June 2017, my truck threw the following codes, P207F and P20EE.
P207F - Reductant Quality Performance
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
The message said I have 200 miles until reduced power. Since it was a Friday, not much I could do at the time so I let it sit overnight, and then the next morning the message was gone. I plugged in the OBD reader and cleared the only remaining code (P20EE), and its been a very happy truck until yesterday.
So my question, can a bad NOX sensor cause the issue of loss of turbo boost, with no codes? Is there another possible cause?
View 3 Replies
First there was a loud pop as if a hose came off and a power loss - don't seem to see any hose disconnected. Happened to me once and seemed to return to normal and then happened to my son. Have not driven since the last time. Both times pulling a boat.
Second issue has been going on since I got the truck - bought used apprx. a year ago - believe it to be stock. The time from pushing accelerator until actual kick in is very elongated - sometimes worse than others but very long on the worst side. Usually noticed when needing to pass on the highway. Once kicked in truck runs well.
View 5 Replies
So, I was on a road trip to Arkansa from Missouri when my truck started loosing power and eventually just died. After I tore through some stuff, I realized the ficm was just floating around off the brackets and even better yet, missing the top cap where you voltage test. And to my great luck, there was a small coolant leak that dripped it's way right into it.. So now I'm looking at replacements and it looks like I'm going to go with the Bulletproof Diesel ficm. But my question is, can I just swap them out and go.? My truck is tuned with an SCT tuner and was tuned up when it died. Should I tune it back to stock before I put a new one in or put the new one in and then put it stock and retune it after that.? Or is it more complicated than that and I should just let my mechanic deal with it.?
View 12 Replies
2005 F250 SD, Crew Cab, Diesel 6.0L...
Hauling my jeep (close to 16,000 pounds all in F250+trailer+jeep) on a highway going a little over 70mph up a hill when I seemed to have lost some power and the check engine light came on. The turbo PSI was well over 20PSI (according to the gauge in the dash). I have a Scan Boss but I have not been monitoring turbo boost PSI.
I was only 10 miles from the final destination so I continued without stopping. It seemed that the turbo was limited for the rest of the trip. Later in the evening, no more check engine light but I haven't really driven the truck since then.
What do you think the problem was? What should the course of action be?
View 9 Replies
I have an 03 6.0 Power stroke. My problem all started the other day when I started to occasionally not get any boost on acceleration and lose of power and a lot of vibration like it's about to cut out but it got worse now today I drove it about 5 miles into town when I got to town I noticed a rough idle I got gas in a gas can not in the truck. I got back in to leave and I had absolutely no power at all the truck stalled out and it was very hard to start finally got it started and it runs really rough almost like it's going to shut off.
So when I started driving I would only make it about a mile or so with out it chocking out and having to let it site for a minute or two and start it back up and go another mile or 2 and have it do the same thing all the way home all the time I have vary little boost if any at all except for when I first pull out now oil pressure is good and engine never over heated some of the codes I have is an EGR code and a contribution balance code for several cylinders I was thinking possibly a maf sensor or a clogged egr not working right.
View 14 Replies
Getting DTC P0401 on my 2011 with 92K miles. First time I got the CEL, we were on vacation, so I read the code, took a screen shot, then cleared it. Called my normal dealer, setup an appt, verified that they thought the truck was safe to drive. Coming home from vacation, I was pulling the TT in my sig, and noticed significant loss of power on hills that I have pulled many times before that I couldnt even hold 55 on now. Transmission dropped into 4th a couple times, on hills that it would sometimes stay in 6th, or at most drop to 5th.
CEL stayed off for a week , and came back on again. The funny thing is that after a day or 2, the CEL went back out on its own. I read the codes the P0401 is still there as a stored code(I did not clear this time). Around town the truck drives fine, the only thing I noticed was the decrease in power when towing. Truck is at the dealer now. TECH "isn't convinced" yet that there is a problem. He is not finished diagnosing yet, and I am sure that he has specific tests to run, but I am starting to fear that I will be getting the call to come get my truck.
View 6 Replies
