It's -15f today. I have been wanting to make a cold start video for a while. Today seemed like a great day to make one.
A little longer crank than when i plug it in, but I think it started pretty good.
[URL]
I have a 2006 f250 6.0 203,00 miles. At 196,000 miles turbo went out, bought power max turbo, redid head gaskets with studs, had heads shaved flat, replace oil cooler with ford part, egr delete, custom tune, aftermarekt 48 Volt FICM.
Truck ran great until 1 day didn't start. had to let truck cool down and then it stared oil pressure was only going to 350psi. drove home fine, shut it off and wonted start hot. drove it a few times after that just let truck idle. Then it started to crank longer when cold. Replaced dummy plug and stand pipe on drivers side only. Then truck was ok for a few drives then started to get a studer sometimes when idling. It got worse then was getting a misfire cyl 1 then, truck died 1 day turning around and would only build a 200 psi.
Replaced stand pipe and dummy plug on passenger side, and IPR, now getting misfire on cyl 8 and P2284, truck runs like crap, bad idle, rpms weird/gas pedal. idle is higher than it should be. when truck is first started shacks very bad, engine very nosiey. ICP 1046 psi(1.27Volts)Desired 637.9, idle and ipr 14.84, truck idles ok, when u punch gas revs up and comes back down, misfire gets worse with rpm.
Then icp goes to 870(2.23 Volts)Desired 870 and doesn't change when getting on the gas and ipr 32.42, punch it and rpms go up more then come back down. Truck starts to shake again. Could running it for so long with bad oil pressure or to much air wreak the injectors? When cold can shut off injector 7 or 8 doesn't change idle like all others do. Once warm 7 or 8 does make a small change in idle. If i command ipr to 20% idles fine, but icp no change from 32.42% to 20%...
I have noticed that my truck will crank longer than normal when i park backed into my drive way but it only does it every now and then. I am guessing an internal oil leak but it starts fine cold or hot.
View 10 RepliesAc is no longer blowing cold air and was thinking about trying a can of ac pro on her. However, I have heard some pretty bad stories about people killing their compressors and overcharging the system. Is it not worth the risk.
View 7 Replies6.0 has had dummy plugs and stand pipes replaced and still has a long crank when cold. The kicker is that it doesn't happen when the truck is parked nose up in the driveway. It only happens if the truck is level or back into the driveway. I suspect it's that the HPOP is losing prime from somewhere.
View 6 RepliesThe past couple of cold starts (not real cold mornings though) I have experienced long crank time to start. Once started she starts normally. No time to read but I'm getting a little worried that I'll get stuck somewhere. I'll check back with my phone when I get into an area with cel service.
View 14 RepliesI just started having an issue on my 01 7.3 f350 with 203k miles, it will crank much longer then normal to start. If you shut it off then try to restart right away it starts normal, if you wait 10 minutes long crank again. if you shut it off and turn key back on but don't start it you can wait an hour then start right away. IDM bad? Vacation in 2 weeks and I would like to get this fixed first.
View 14 RepliesSo we have a van with the 6.0. It has a little over 100,000 miles. It has started to take longer to up shift. The dealer ( I know. but I know my service guy and he has done well in the past ) says we need to do injectors and fuel regulator plus a host of small parts to do the job. about 8 grand or so of work. Everything on the trans checks out and is supposed to be in perfect order. Truck goes well once up to speed but its getting the is the problem. So its parked so we don,t melt an injector.
View 3 RepliesLately it seems that my 6.0 cranks over longer before it starts. it used to turn over quick and start not it turns over at least 5-8 seconds maybe more. .
View 7 RepliesI've had my 6.0 for 2.5 years now and got really acquainted with what makes what noise, and how long starts took etc. recently this morning, i had a longer start, longer than a normal long start (4-5 seconds). Felt too long to me, but it started and didn't turn it off to try again. Got to my destination, turn the truck off and brough up ICP, FICM, FICM SYNC and cranked and watched.
After 1 second ICP jumped to 600 then to 770 and 2-3 seconds later FICM sync finally read 1 and it fired. What can be causing the sync to take so long? I have had intermittent no starts before, maybe 4 in the 2.5 years i've had it and every time i have pushed on the fuse blocks by the driver batteries, and also pushed on the FICM connections to make sure everything was okay. That seemed to always work.. But no amount of pushing on them are solving the long start that is happening...
When I got my 2016 back at the end of last October, the pink coolant in the main degas bottle was just visible in the clear top half of the bottle. By the time 5k miles rolled around, the coolant was no longer visible in the clear section. At oil change time, the dealer "topped" it, resulting in it being visible in the tank again. 3k miles later, the coolant has disappeared below the clear part of the bottle again. What gives? The secondary bottle level has not budged. Its clearly not losing a lot, but it is definitely going down slightly.
View 14 RepliesI have been having a problem with the fog lights on my 05 F-250 super duty truck. They won't come on when I'm parked but when I'm going down the road they'll come on and usually go right back off or will stay on for a min or longer but still sooner or later they go out. I think it's a shortage somewhere but I'm not sure on whether it's in the switch on the dash or somewhere in the wiring.
View 2 RepliesDriving today I noticed a hot smell, it went away shortly after. When I got home I noticed the electric door locks no longer function. I guess this will be a test of my 3rd party warranty!
View 10 RepliesAbout 7 months ago my truck started cranking longer than normal to start after sitting for more than 2 hours. This went on for about 3 weeks, then it started normally again. (By longer crank time, i timed it between 5-7 seconds on average. Normal is about 2 seconds). Now it has started doing this again about 4 weeks ago. Now I'm thinking HPO slow leak. Yesterday all is good again. What should I be looking for as a starting point to fix this permanently? When it cranks longer, the icp stays at 0, the ipr goes to 77%. Then it just fires off. No slow build of pressure. You can see all my mods and updated parts in my sig. I wonder if one of the new dummy plug o-rings is starting to give up already after only 15k miles. (Batt voltage is at 13.9-14.2, ficm is at 49.5 steady).
View 5 RepliesI have a late model 2004 F-350 6.0 powerstroke. 182K miles. Auto Transmission
What happened. Condensed version
Left house, drove out to highway, got on highway. Everything feels normal.
About 1 mile of going 70mph, I notice I can no longer accelerate. after 1/2 mile, I begin loosing speed, and engine will not rev past 1000 rpm. I eventually pull over (another mile), put in neutral and will not rev past 1000. put in drive and start to idle to highway exit. it gets about another .5 mile and begin going up a hill when it completely dies. Will not restart.
No prior issues with the truck. Full tank of fuel.
What I have tested so far. Ficm 48.5 volts cranking. Icp .225V KOEO, .875V Cranking. LPOP is registering pressure on the dash. No Fault codes.
I have gotten it to start twice now, one time it allowed me to rev to 750 rpm, where i used 4 low to make it onto a trailer. second time would not rev at all. idling at 250-300 rpm.
That same night as it died, I drained the transmission pan/ TP filter and filled with 8.5 Quarts of Mercon LV. This is the first time I have done this since purchasing @ 161K miles. Everything seemed normal, no leaks present.
Also my buddy showed me how to enter the dash test mode and we cycled through these. Not sure if this is relevant.
So, What do I test next? I don't think its HPOP issue since the ICP is reading .875 volts at crank. I did unplug the ICP and it still would not start. I don't think its the injector side of the ficm because they buzz as normal with koeo, but this is a possibility as I don't have equipment to test. Egr valve is clean for age of truck.
Would it be possible that the Mercon LV knocked crud loose in the transmission causing it to fail/seize? would siezed tranny cause the engine to behave in this manner?
Fuel bowl on top of the engine was full of fuel. I have not pressure tested it yet as I can hear the pump running during key on.
could i have a bad crank or cam sensor?
Multi-injector failure?
Bad Icp with HPO failure?
I have an 02 f250 230,000, first 7.3. I've owned it since Oct and put less than 6,000 miles on it. I have another cold crank no start. New glow plugs and Glow plug relay last weekend. Worked fine that weekend. It sat all week, then crank no start fri night, it was like 70 degrees for the high that day. Plugged it in over night and it started. Did not fire right up cranked it for a couple seconds. I drove it all day, started every time. Valve covers have 5,000 miles on them. Fuel Filter heater fuse not blown. But don't know how to check it for sure. And don't know where to go with it from here. Getting frustrated with crank no starts. No troubles found.
View 2 RepliesSo back ground is as such. Truck started fine before I replaced the hpop with t500 and did the driven diesel regulated return. I have double checked everything is plugged in. Now when I try to start it cold it will just crank. Yes I get smoke and oil pressure both places. If I give it a shot of ether it will start right up and run fine all day. What am I missing? Yes I know ether bad.
View 14 RepliesWhile priming the high pressure oil system were using the starter jumper wire but after a while I wanted to watch the insight so I pulled the ficm relay but then it wouldn't crank with the key but before I pulled the ficm relay it would. Now it will start if you turn the key on and use the starter jumper wire but it still won't crank with the key. The truck has a viper alarm system I am thinking that might be causing the issue. How to trouble shoot that? Also I don't know if it is related but it has to crank for too long before it starts.
View 3 RepliesStopped at the store, came out, started truck, ran for two seconds, shut off, hasn't run since,had no codes,or any other issues. I have checked all the fuses,breakers,main power supply off of passenger battery, still nothing. I have head and taillights, power points on dash, dome lights, chime for headlights. 79674 miles.
View 6 RepliesI had issues with my F250 cranking last winter when the temperature dropped, so I changed out the glow plugs in the spring. I hadn't been able to truly test them yet, since it hasn't been cold, but the other morning my truck wouldn't crank up. It was 40 degrees out the night before, and it had been almost 24 hours since I cranked the truck, but it seems to me like the truck shouldn't have an issue in that mild weather.
I'm not sure what I need to do next to try and fix this problem, it's been driving me crazy and risks stranding me if I park for a while in an area where I am unable to plug by block heater in. The truck cranks fine when I have had it plugged in for a while, so I'm fairly certain it's a heating issue. I haven't done any tests since last year, but I know that the GPR was working properly last winter, which is why I changed out the glow plugs.
I have a early 99 f250 super duty 7.3l and it's giving me fits. about a month ago the truck started to do a hot no start. drove truck for about a hour. Shut it off and half hour later no start. Let it sit over night and would start with long crank.
Changed CPS no change. Pulled tuner and set back to stock. No change.
Changed fuel filter, no change.
After reading forums changed IPR and truck started and ran great. About a week ago back to the same problem. Battery's are about 2 months old. Oil change and oil filter a month ago.
Checked the hpop reservoir and its 1/2 from the top.
Checked fuel bowl and it has fuel. no sign of oil in it.
Drained bowl and watch bowl fill back up. seems to fill quickly.
Pulled passside valve cover to check for bad orings while cranking.
Every thing seems fine. have not done driver side yet. used FORSCAN and ran buzzed test on injectors and they all buzzed what seems to be about the same. ran test couple of times to make sure. this morning I ran a live scan while cranking and this is what I got right before it started. ICP 660.6psi, IPR 64.84% and RPMs 227. took 8.86 seconds to start. after work scaned again for hot no start and this what I got. ICP 292.9psi, IPR 55.86%. and RPMS 203. unplug ICP and no change. still will not start. one thing I did notice when plugging ICP back in I looked down in side at the pins and can see what seems to be bubbling around one of the pins. the pig tail has just the slights sign of oil.