The past couple of cold starts (not real cold mornings though) I have experienced long crank time to start. Once started she starts normally. No time to read but I'm getting a little worried that I'll get stuck somewhere. I'll check back with my phone when I get into an area with cel service.
View 14 Replies2005 Ex with 6.0. It has been bulletproofed. But has had a long crank after sitting for over 5 hours. I was starting to think glowplugs but no codes, Then thinking FICM, nope voltage has always been good. After I run the truck for a few miles if I kill it. It would crank right up. No issues. Only happened after it sat for awhile. I knew it had to do with HPOP system since it took about 5 to 8 seconds to show over 500PSI.
The passenger side does not have a leak since the oil is to the top of ICP sensor. When I was going to remove it. So I took off the drivers side. I inspected the dummy plug. No issues there "they are the 12mm with teflon plugs" I inspected the stand pipe. No issues there either. I inspected the small test port on the top of the rail. No issues there either. So I decided to air test it. So I used my auto-ingenuity to close the IPR valve after I heard all the oil blow out.
Then after sitting with 120 psi of air for about 10 minutes. I hear a bubbling sound coming from the Drivers side Rail. It was a plug I have never seen mentioned here. It is at the back of the rail. I removed it and sure enough the oring is split in 2. I went to ford and picked up a new Oring it was like $4. It also looks like its a different material. I am still in the process of putting the truck back together so i have not started it back up. But I am pretty sure this was my problem.
I recently (in the last few months) have noticed my truck (1999 F350 duallie) seeming to be running very rich … I pull a 32' trailer with it and noticed on the art few trips the front and right side of the trailer covered with diesel fuel spots when I got home …. It also smells very rich when idling…. The last couple times I started it in the mornings it seems to crank a very long time before it starts …it still runs but its got issues evidently … it has these 3 codes :
P1280
P0475
P1670
The 1670 will clear , but the other 2 I can't clear, they are right back every time you turn the key on …
So how long does one have to crank until it is considered an extended crank? 2 seconds, 5 seconds, 10 seconds.....?
The reason I ask is after all the motor work I did on my truck sometimes she fires up in less than 1 second of cranking and other times it take maybe 2 seconds of cranking. I do not think 2 seconds is considered and extended crank time but was just curious about what is considered extended cranking.
I have a 2006 F350. I have long crank times. No Codes. I have Autoenginuity with Enhanced Codes and everything shows fine. I replaces standpipe and dummy plugs. Glow Plugs and harness. I was hoping it not be the STC but I needed to do oil cooler so wanted to eliminate STC. Got truck apart and the STC Fitting is newer style so I'm kinda bummed out. Not sure if I'm missing something and as far as I have it torn down is there anyway to test what could be causing the problem? Or just put it back together and keep my fingers crossed that whoever put the new STC fitting in screwed it up. I'm beginning to not like my truck.
View 8 RepliesRemoved my oil rail to replace standpipes/dummies (04 Wavy rail) and now I have huge crank times to start. This is after the initial Huge crank to get it started. Do I have air in the system, or did I bugger something. I did the whole deal very careful. I lifted the rail up very carefully, pipes removed. I lined up the rail nipples with the injectors and evenly pressed it back in place, and then inserted my dummies/standpipe. Tightened the rail to 120 inch lbs then the dummies/standpipe to 60 ft lb. I did my son's '06 a month ago with no troubles. (didn't remove rails though). Once running it sounds perfect, turn it off and re-start and it's a long crank (30 seconds or more). I have not monitored ICP/IPR while running, will try that today.
View 8 Replies6.0 has had dummy plugs and stand pipes replaced and still has a long crank when cold. The kicker is that it doesn't happen when the truck is parked nose up in the driveway. It only happens if the truck is level or back into the driveway. I suspect it's that the HPOP is losing prime from somewhere.
View 6 RepliesI think I'm going to buy a late 99 CCLB six speed manual truck that's probably been sitting all of a year, maybe longer. Prior to being parked the truck ran flawless. 6 months after parking it he decided to sell it and when driving it, it has a miss when its cold and blows a little white smoke when accelerating. Appears to clear off and run normal after its warm. So he decided to investigate it and re-o-ringed the injectors and checked other things out.
He's determined he thinks it has a weak hpop. Not sure I'm sold on this. Fast forward six months and now I'm pretty sure I'm going to buy it. Drove it yesterday and same thing, first 4 or 5 miles kinda studders or misses but after that runs smooth and has no issue. No longer blows white smoke at all or anything. Obviously the fuel is old as hell, other than that what is everyone's thoughts?
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
I have a early 99 f250 super duty 7.3l and it's giving me fits. about a month ago the truck started to do a hot no start. drove truck for about a hour. Shut it off and half hour later no start. Let it sit over night and would start with long crank.
Changed CPS no change. Pulled tuner and set back to stock. No change.
Changed fuel filter, no change.
After reading forums changed IPR and truck started and ran great. About a week ago back to the same problem. Battery's are about 2 months old. Oil change and oil filter a month ago.
Checked the hpop reservoir and its 1/2 from the top.
Checked fuel bowl and it has fuel. no sign of oil in it.
Drained bowl and watch bowl fill back up. seems to fill quickly.
Pulled passside valve cover to check for bad orings while cranking.
Every thing seems fine. have not done driver side yet. used FORSCAN and ran buzzed test on injectors and they all buzzed what seems to be about the same. ran test couple of times to make sure. this morning I ran a live scan while cranking and this is what I got right before it started. ICP 660.6psi, IPR 64.84% and RPMs 227. took 8.86 seconds to start. after work scaned again for hot no start and this what I got. ICP 292.9psi, IPR 55.86%. and RPMS 203. unplug ICP and no change. still will not start. one thing I did notice when plugging ICP back in I looked down in side at the pins and can see what seems to be bubbling around one of the pins. the pig tail has just the slights sign of oil.
I'm having a long crank cold start issue. It takes about 2 five second cranks before the truck will start up. It just started acting this way yesterday before I fired it up to go to school. After its warm it fires up no problem the rest of the day, just takes a bump of the key.
I don't think it's the GP system as this truck has started at -20 to -25C all winter long unplugged with no issues. From my reading some sources say that it could be a HPOP leak, maybe dummy plugs?
Is there any way for me to do some more diagnosing - places to look or test for? There are no stored codes other than an EGR code due to the delete. Truck is completely stock with atlas 40.
I own 2013 Mk6 GTI. I am having to over crank the engine for a period of 8 seconds or so before the car starts, especially after it has been sitting for a few hours. My thought was a faulty check valve in the fuel pump. I have heard that our fuel filter has a built in pressure regulator that may get stuck open for whatever reason and that may also cause a long crank time.
View 9 RepliesI have a 1988 Dodge pickup 1500 with a 5,9 gas engine. It used to pop right over all the time. Now, in the morning, I have to crank it forever until it starts, and if it sits for 1 hour or more, same thing (have to crank for a long time). It is my understanding there is a valve called a one day valve that holds pressure on the gas line. Is it possible this valve is not working properly? And if so, do I have to replace fuel pump to fix problem? once started it starts up with no problem until it sits for hour or more then hard to start.
View 15 RepliesSo, a year ago or so I had the truck die on me, it would start after cranking it a long time and cough/sputter for a few minutes with no power. I thought it seemed like a weak hpop or leaking oring, so I tore it down and put it all back together with a something or other hpop. Now I have a no crank no fuel pump condition, the injectors don't cycle when I turn the key on, I do get relays clicking, but no start, the yellow/blue wire gets the starter to turn over, but no fuel, so couldn't start if it wanted to... I am getting 120 ohms (like 122) on the dlc 6,14 and millivolts, basically nothing between 4 and 14...
I sent the ficm off to get rebuilt and they told me that it was already good (charged me anyway though, ah well...) I wiggled wires around and pulled my ficm plugs apart and pushed the wires in some, didn't seem to move any... What is next? There can't be that many things that cause all three, No Fuel Pump, No Crank and No Injector Buzz, can there?
2003 6.0 will fire within 2 seconds when cold, literally a "bump the key" and she fires up scenario. Recently and only when the engine is hot I'm getting extended crank times and sometimes it takes several attempts for the truck to start. I replaced the HPOP with an upgraded pump after the factory HPOP went out at 311,000 miles. I know this sounds like a standpipe leak scenario but it doesn't act up all the time, sometimes it fires right up even when its hot. my thinking is a leak is a leak and only gets worse.
My IPR is reading in the 26% range, FICM is steady in the 47.5 to 48 volt range and at idle 585 to 600 psi on the ICP with a good FICM sync. I'm going to to use my scan gauge and see if I can catch an extended crank scenario to see if the ICP is reaching 500 psi but is there somewhere else I should be looking? FICM relays possibly? I've noticed when i turn the key on I'll hear the fuel pump,vacuum pump but the clicking sound is very brief or nonexistent (not sure what the clicking noise is from I assumed glow plugs but its absence is noticed)...
OK here we go it all started with a long crank and now no fire. I changed cam sensor wiggled wires got to fire , shut off than nothing . Changed wire from cam sensor to about 6" from ecu found small nick in wire. Swapped ecu no good... I am getting my numbers from torque app.
ficm sync = 0
RPm = 172
FLP = 12
fmp =49
Hpop = 1823 max
Ipr = 80.9 max stready at 48
ipr volt =.02 at rest
Also tested fuel pressure at filter 80 psi ( blue spring)
ficm sent to ficm repair, tested good
cam sensor changed , pig tail also
bubble test on fuel filter no thing there
So any thing else to check or am i looking at a harness change?
So my recently purchased 2005 f350 has an abnormal long crank. I searched all the internet and everything pointed to STC fitting. Well I knew I had some other things I wanted to knock out so I ended up buying an update kit from sinister diesel. It included an updated fitting, new degas cap, updared turbo oil feed and return lines, blue spring update, and "dummy" tubes or something like that.
During the last few days I have removed the turbo, and finally got to the hpop. As I was removing the turbo I thought I might have the updated lines as there was no braided area in the feed tube. Sure enough I pulled the hpop and I have the one piece fitting. So now that I have wasted all this time removing all this stuff for no reason I still don't know what is causing my long crank. I am going to probably install the new fitting and lines anyway but where do I go from here?
I'm thinking this is probably just the way they are, but I don't understand why........... I have a '12 F250 supercab 6.7 FX4.... truck is an XL, no supplemental heat or anything. If it sits outside over night, and I go out in the morning after say a 35-40 degree night, start it up and let it run 10-15 min then drive 5 miles down the road to town, both temp gauges are still pegged on the cold side, and there's virtually no heat blowing on the defrost. Even if it sits in the heated garage over night, same temp, same drive to town in the morning, same lack of any heat.
My old 2010 V10 that I traded for the 6.7, and my current 09 5.4 are the exact opposite of this. I can start the 5.4 cold, leave within a minute or two, and be making some heat within a few minutes. By the time I get to town, everything is well in the normal range, and I'm turning the heater down cuz it's too hot. Even once the 6.7 is fully warmed up the heater doesn't seem to make near the heat that the gas trucks do. I love the 6.7, I just find this a bit odd. Am I missing something, or is this just the way they all are?
Long crank to start hot and cold. Acts like missing when its cold tho and when it warms up it runs ok but it will set code weafher warm or cold and u can turn it out with scan tool and drive and it wont come back till restarted again...
View 1 RepliesI need to get my oil cooler replaced but that's besides the fact. I drove it on a little trip the other night ran fine. Then went to start it after i was done with what i was doing turned it over didn't start the first time. Cycled the key and cranked it again. Started up drove it back home on the high way no spitting or sputters got off the high way it started idling like crap and shaking as i accelerated but made it home. Let it sit over night and day (was at work) got home to start it and it fired up no problem but still idled funny.
Revved it a couple times and it seemed to clear up so i took it around the block. Floored it and it ran like it was suppose to then go to the other side of the block floored it again and it had no power and sounded like it was running on 4 cylinders. Pulled it back in the driveway idled weird and cleared up again went down the street and floored it ran like a scaled ape and then just died. tried cranking it over and nothing finally got it to start after holding the ignition on ran and then died again. Got it pushed home and decided to fire again after a VERY long crank and it idled for a couple minutes very horrible and died on its own and hasn't started since.
My 06 currently has 296k miles. 3 years ago I put a lot into her. Dummy plugs, stand pipes, STC, hg,studs, oil cooler, bpd egr cooler. Cleaned spool valves and fresh o rings in injectors. (Alliant) plus a lot more that I can't remember. Ran very very well after all that.
Fast forward to a few weeks ago. Driving down road and truck died as I let off pedal to slow down for turn onto my road. Took about 7-8 tries to get started back up. Icp was reading in the 300's until it finally started. Made it home. Shut it off. And started right back up.
Few days later truck died again same way. Let off to make a turn. Several attempts to restart icp was in the 300's again. Once it started building 420ish it sounded like it was firing a few injectors and slowly started running. The next time it happened the same way but when I got it back running I eased to my inlaws like less than a mile. When I got to their house and pulled in and went to back up to turn around the display on dash said low oil pressure and started missing a little. So once I got home started researching.
A few days ago I pulled out the low pressure oil regulator to check it out. It was clean but did have some mild scaring. I used some fine scotch rite and smooth it out a a little. It moved freely in the bore so I put it back together. Then pulled the oil filter cap off to check the little black valve. I noticed the filter was not dripping with oil like normally when I change the oil. And yes it's motor craft filter and cap. It checked out ok. Press it down and turned engine over and it filled and held. Let off of it and it drained.
Next I air checked the high pressure side. Applied air and waited until I could hear the air (IPR still open) then closed the IPR. Couldn't hear any leaks. Just a very very minor his and couldn't pin point where. So I went ahead and went to dealer and got new stand pipes and plugs. And ordered new print set for injectors. Pulled injectors and didn't see any smoking guns. Replaced prongs, stand pipe and dummy plugs and put it all back together. Cleaned the injector cups and hold down bolt holes. Torqued injectors to spec.
Got it all done and rotate motor by wire next to heater blower to assist prime system. Tried to start it up and it took two tries but fired right up and sounded smooth as hell. After it idled a few minutes I saw a haze from exhaust. It smelt just like fuel. A few minutes later started idle a little rough. Gave it some go pedel and it was rougher at about 1600-1800rpms and couldn't feel it above 2k. Got my laptop out with AE and done balance test. Did not show anything. No codes either.