Ford 6.0L Power Stroke Diesel :: Intake Air Temp Sensor One Circuit High And Strange Idle?
Aug 11, 2016
I have a code for iat sensor 1 circuit high. It's the only code I can pull. I replaced the sensor in the manifold and still no change. The truck revs up when started but kinda finds its idle rpm after a second and the idle fluctuates some when the truck is warmed up too. I have a snap on solus and all parameters seem to be good. Icp sensor is also new thinking it might be the cause. Other than that the truck runs perfect and doesn't miss a beat.
View 14 Replies
Advertisement
I'm excited to be a Powerstroke owner again! I had a 2000 with the 7.3L and since bought and now sold a Chevy 1500. Last week I bought a new 2015 6.7L. I am MORE than impressed and love the truck. Today I brought it to get the windows tinted. I have not had one issue with the truck since I have had it. When they finished with the windows, my check engine light was on. The shop I had it done it EXTREMELY reputable. They brought out their snap on scanner and pulled the code. p0073 for the ambient air temp sensor circuit high. Is this a coincidence that this came on after they got done, or could something they did while tinting the windows tripped this?
As I drove off down the road after determining I wasn't going to hurt the truck, the air temp sensor went from showing -40 to the actual temperature. What would cause this? I deleted the code when I got home with my actron, and the MIL has stayed off since, however, it shows P0073 Permanent ...
View 11 Replies
P0073 Ambient air temperature sensor circuit high. Preliminary inspection, right outside mirror badly damaged/broken. Guess where the sensor is?
View 6 Replies
Noticed a while back that the plug for what I assume is the air intake temp sensor is looped. I assume because I can't find the sensor anywhere. how critical is the sensor? The new S&B has a hole for it so it's either gonna need a new sensor or a plug. The local autozone has one for 16.99.
View 12 Replies
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 Replies
I have an emissions test coming up. I have 3 P codes that I'd like to eliminate before then. I don't want to "fix" the issues they are telling me about. Just make the codes go away. I know why they're there I just need to get rid of them.
What I have coming up is:
P0475 Exhaust Pressure Circuit Valve (result of EBPV delete)
P0541 Intake air heater A circuit low (result of aih delete)
P0640 Intake air heater control circuit (also result of aih delete)
What resistors I'll need and where to put them in?
View 12 Replies
I have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...
View 5 Replies
Have a 2004 F350 which had problems starting cold and once started had bad throttle response until warm. It also had a shudder at cruising speed when going up a slight incline, would shudder until turbo kicked in.
Pulled codes which related to FICM and codes for all 8 injectors. 7 injector codes were circuit low, cylinder 1 high. Tested FICM voltage and sent FICM out for repair.
Installed rebuilt FICM, cleared codes, and hard start went away, but cruising shudder is still present.
Only existing code is P0262 for cylinder 1 injector circuit high. I'm assuming that cylinder 1 injector is bad -- are there any tests to confirm before I take it apart to replace it?
View 7 Replies
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 Replies
I've had good running on the truck but lately in the cold the idle has a weird skip to it like it's missing on a cyl. It will start fine, and run fine for about 30 seconds. Then it will start to mis. When giving pedal it goes away and it's driveable but it doesn't sound right. After a bit of running it's fine for the duration while warm. My monitors are I think all good, 48.5v, icp about 1250 psi. Is this the famed "injector stiction"?
View 5 Replies
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
View 14 Replies
I have for a week suspected my batteries were getting weak. just slower cranking is all. I took my truck in to have a viper security system installed and while he was doing his work he killed the batteries. I saw him hook up a battery charger and started the truck. He pulled it around to me and explained how the system worked and off i went. 5 miles down the road, on the thruway, I notice a miss and I'm down on power. FICM looked ok, 48V and it was charging, 13.8 I thought I would bring it to my shop and load test the batteries. On my way here, the check engine light comes on. At the shop, load tested them and they were weak. Installed 2 brand new batteries, started it up, no difference. Hooked up the scanner and pulled a code P2077 (cylinder 6 injector circuit high) Now what? I'm not sure where to go from here. I'm guessing either the FICM went bad or the #6 injector?
View 12 Replies
I know they're supposed to be within 15 deg of each other. How bad is this? Pulling a small trailer with a polaris rzr on it. Running 75mph
View 14 Replies
Oil temp sensor - when I turn the truck on - it goes right to half way. I am guessing it is broken ? But then again, if it was broken, why would it go half way ?
View 5 Replies
My dad's 03 has had some work done after his oil cooler was clogging. New oil cooler, egr delete, head studs etc. The oil temp seemed to run some what high when he got it back. After a couple interstate runs on cold days 15-20 degrees, the water ran around 185 and oil as high as 218 but usually a bit lower. What's going on here? how could this thing be clogged again? It hasn't seem to gotten much worse since we got it back but not better either.
View 8 Replies
I recently noticed on my truck that my oil temp was running high, I would go down the interstate at 75 mph and the oil temp would get up to 215-218 while my coolant temp would sit around 192-196. So, I took it into the shop and was told it was most likely a bad oil cooler and had it replaced 2 years ago when I had my injectors and gaskets replaced along with my egr deleted. So, got the truck yesterday, going 60mph down the highway, truck ran an oil temp of 192 and the coolant at 188. Was great, but later on once I got to the interstate going my 75 mph, The oil temp jumped to 209 and my coolant sat at 192. Not sure what the deal is, was told the oil cooler was replaced and wanted some input on what else I could be looking at. I currently have 5w40 synthetic oil running in it. I have an EDGE CTS tuner on it and tuned it back to stock mode, but oil temp still jumps up to 209 and coolant remains around 190-192.
View 14 Replies
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 Replies
I have recently bought a 04 f250 6.0, and it has the intake thumping noise that varies speed with idle... I was told it could be a broken rocker, a bent push rod, or a broken roller... I am not that much experienced with diesels. I've spoken to the dealership, and they don't wanna fix it, they said it wouldnt hurt it to drive it like that, but the noise bothers the hell out of me, and everyone notices it. so i wanna get it fixed. I am hoping its just a rocker. if it is just a rocker how deep am i in? truck has 240xxx miles on it, and runs perfect other than that noise.
View 7 Replies
Trans temp used to be about 185 max, now it's running side by side with coolant temps (200-203 with Mishy 200 thermostat) after I did the 08 pan and filter upgrades. I added 9.5qts after the change of Valv Max Life and checked and double checked the dip stick bout half way up hot. This is normal operating conditions, not towing anything. Checked with TorquePro App. Why it would run so high? Did I do something wrong?
View 14 Replies
Just over 6000 miles....Yesterday morning the light came on. Dealer wouldn't look at it for a week. Went to my mechanic this morning to check the code it was p0181 fuel temp sensor. I read something online about the block heater making it too warm. The other night it was cold so I plugged it in, then yesterday morning it got warm overnight like into the lower 40s. I noticed the grill felt warm too. My mechanic cleared it if it comes back on do I have an issue? Is it ok to drive?
View 14 Replies
I have a 2006 350. When I am pulling my camp trailer (about 12,500 lbs) up a grade I hear a fan or blower turn on and I get a high pitched squeal. It will also have a beep and my in dash display will say high engine temp. I have a bullydog pmt programmer (i tow with it in stock mode) the display will show my coolant temp at about 180 degrees. If I pull over and let it idle for about 2 minutes the warning clears and the temp gauge returns to normal. the display reads about 180 degrees the whole time this goes on. I know the engine is not over heating so why do i get this warning and squeal?
View 4 Replies