Ford 6.0L Power Stroke Diesel :: Heater Hose Installation?
Nov 23, 2015
Had a large puddle of coolant under my '05 X this afternoon after work. Seems it's leaking from the Y connection coming off the heater water control valve. See first pic.
I think it's part number 18472 (labeled with the circled 1) on left side in pic #2. Need to confirm this is the right part and the full part number?
Lastly, how the heck do you change this hose? It's tucked up under the cowl and looks like difficult.
View 14 Replies
Advertisement
First there was a loud pop as if a hose came off and a power loss - don't seem to see any hose disconnected. Happened to me once and seemed to return to normal and then happened to my son. Have not driven since the last time. Both times pulling a boat.
Second issue has been going on since I got the truck - bought used apprx. a year ago - believe it to be stock. The time from pushing accelerator until actual kick in is very elongated - sometimes worse than others but very long on the worst side. Usually noticed when needing to pass on the highway. Once kicked in truck runs well.
View 5 Replies
So I installed a new IPR valve. Now it cranks but wont turn over. I read something about how the IPR valve has to be 'clocked" in the same exact position it was in when I took it out? Would this cause my truck not to turn over? Truck has never not started before.
When I tightened it down, it was not in exact position as the old one. If I wanted it in exact position as old one, it would have not been tightened correctly. I couldn't make one more full turn around. what do u think???
View 14 Replies
Installing the ford accessory dvd players for trucks? not sure if i want to get them just yet but i am looking into options since i have a sunroof and cannot install an overhead player..or can i? I just want to know what you have to do to install them? do they work good? does the leather match?
View 8 Replies
Well on the way home from work I got the P0069 code AND I noticed that when I get off of the throttle quick the turbi spools down slower? What should I be looking at? Map hose?
View 14 Replies
My orange one leaks, bought a blue one. How the heck to I install it? I have decent tools.
I reviewed the threads on coolant flush and fill, and bought a coolant filter kit, I will be doing that at the same time.
View 14 Replies
Is there one thing that when broken makes both the steering and brakes lose all power? Does the power steering and hydroboost share a pressure source?
My brake pedal is dead and I get no steering boost, but the master cylinder and PSP are full of fluid. Do I replace both, or replace one first to see if that fixes both? Or could it just be a hose leaking? Not sure how to diagnose this one.
View 1 Replies
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 Replies
I remember seeing a few people post about having them installed at the dealer for about 125-150 was this at the body shop or in the mechanic shop?
View 13 Replies
I Have two questions on installing studs. Does the 6 oclock dowel position really matter? To me it doesnt make much sense because the timing isnt changed with just studs so there should be no issue with valve clearance and such. Unless something isnt installed correctly.
Also what is the best way to clean the block? I thought Senior Master Tech on youtube had an interesting way with a piece of angle iron.
View 11 Replies
So I recently had the head gaskets done at Ford. All is good but there is a slight drip from the blue EGR hose. It made a 3" circle on the driveway after 8 days. Coolant level is still fine. I really don't feel like dropping it back at Ford. Think I can just twist the hose to tighten it a bit or is a new hose in order? It is only 2 yrs old and was not replaced with the head gasket work.
View 10 Replies
2 1/2 years ago I installed a BPD remote oil cooler with BPD filter. The stock oil cooler was clogging up for the second time and didnt want to chance it. The BPD oil cooler works great. I have never seen high oil temps in any driving condition. Last week I was replacing the hubs and seals on the front of the excursion and noticed the oil was leaking from the 90 at the end of the hose oil filter location. I called BPD and sent them a picture. The 90 is corroded and is failing. They said something about a 2 year warranty but because of the rust they would not send one out for free. I purchased a new hose and the other 90 that goes right after it.
They recommended that I spray it with undercoating or something. I live in upstate NY and deal with a lot of salt on the roads in winter. I do keep the truck clean in winter as much a possible. I am posting this so if there are any others in similar situation you should do something to prevent that 90 from rusting like mine did. If I had known this when we installed it prob would not be replacing it now. Will be replacing it tonight or tomorrow. BPD said I will need a 1 1/4 crow foot or remove the turbo to get to the other end of the hose. Not posting this to bash on BPD just sharing so any others can prevent this part from rusting out.
View 14 Replies
After chasing the smell of coolant for a couple weeks, discovered that the upper radiator hose was leaking at the engine. Based on my schedule and drive schedule, and unfamiliar location this last week, I took my truck to the last people I wanted to - the Ford dealer, where they attempted to charge for the hose replacement. During this time I discovered the nature of how these hoses work and asked the tech why they don't just replace the O-rings ... "Ford Motor Company wants to sell you a new hose with labor" - a direct quote from the Ford tech. And that is why Ford is the LAST place I want to go for repairs I cannot perform. I kept the old hose - any spot where you can get the O-rings alone?
View 5 Replies
Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 Replies
I am sure some of use around the forums have seen some of Diesel Tech Ron's videos, well in this video he is installing one of Bulletproof Diesel's remote Oil Coolers on a 6.0
Bulletproof Diesel's remote mounted oil cooler install on a 6.0 Powerstroke - YouTube
I like the idea of these if you ever have to do any work on the Oil cooler or replace it it would make it pretty quick and you don't have top spend a day tearing the engine apart
I haven't hear of too many people having issues with remote coolers set up's like this. Maybe there are some remote oil coloer owners that have em that can shed some light on how they have worked so far on their 6.0's ...
View 8 Replies
I'm getting pretty comfortable with these forums now. Not sure if this is in the right section, but even if it was, I'm not sure how to find the right one. I recently purchased Bullet Proof Diesel's Air-to-Oil oil cooler along with the BPD oil filtration. I've already drained the oil, but do I need to drain the coolant as well? I have read of people doing a complete flush before even installing a new oil cooler (OEM oil cooler). That way once it is installed, it doesn't have all the grit and sand pumping through it right off the bat. But does it matter with BPD's system? Should I go ahead and drain the coolant completely before beginning this job?
View 10 Replies
Noticed this past month on colder days my upper hose is collapsed, typically a symptom of a bad radiator pressure cap.
This hose is connected from the water pump to the radiator. The radiator is connected to the Degas bottle which has a nonstandard radiator cap.
Do these plastic caps vent the same way a typical cap does?
Cap for 2011 Ford F-350 Super Duty|9C3Z-8101-B
View 3 Replies
How to get the boot or hose off the egr delete tube without having to tear everything apart? mines leaking i have new hose to replace just not sure how to get the old one off...
View 7 Replies
This weekend while towing a light load I noticed my FWT and EOT starting to climb rapidly, EOT reached 260 FWT I think about 240. I exited the interstate to find I had a busted radiator hose. I replaced the hose and filled the system with distilled water, but didn't add antifreeze at this time. The system wasn't completely empty.
I noticed once back on the road my EOT seemed to be higher than normal but FWT seemed to be normal. Could the lack of antifreeze cause a greater delta between FWT and EOT? I have seen articles which state do not use Ford Premium Gold Coolant, but to use CAT EL-1 coolant instead. Which should I use?
View 6 Replies
I have a 2005 F250 with 6.0 and almost 175,000. On vacation right now and noticed when I came out of a store that there was a puddle of water under the passengers side. Chalked it up to AC defrost. The second time I was not running AC and puddle again.
Felt and smelt of it...antifreeze. Just put in all new Zerex G05 and a new degas tank because when working on it I noticed a pin hole in the base before we left. I replaced the EGR cooler and hose from Sinister about 3 plus years ago.
Would the EGR cooler hose be leaking? I've noticed that white residue on top of the intake around the where the hose is. What would cause this, Heat, wear and tare....my luck ?
View 2 Replies
Had a coolant leak I finally traced to the rubber hose on an egr delete (previous owner installed, not sure of brand). Looks like the jackwagon who installed it cranked the clamps way too tight and they eventually split the hose. I have a piece of heater hose that looks like the right diameter and cut to size should fit fine. I guess I am just looking for some reassurance that it would be ok to use in that situation...
View 3 Replies
