If you have a blown head gasket on a 6.0, after the gaskets were removed would you be able to tell where the gasket failed?
Since the gaskets are metal or multilayer metal in some cases would you be unable to tell where the gasket failed or would it always be visible?
I just had headgaskets (oem) studs, egr delete,oil cooler done on my 06 plus water pump cause the gasket blew. I have a sct livewire hooked up monitoring everything and tonight i noticed that the eot and ect's were way off. fully warmed up and rolling 65 Anywhere from 40*-50* out it was eot-156 and ect-172. Degas bottle was at the normal level.
I am also having issues with the fuel gauge. Every now and then the gauge will go to E and the miles to E will display ---. Turn the truck off and back on it works again. I am half assuming its the plug on the sending unit or the sending unit itself.
I just pulled the cab and did headgaskets, studs. I put everything back together and when I turn the key, nothing, no lights, zero.
I've checked all connections and batteries are good, checked all fuses, where to start with this?
So I am just wrapping up getting my head gaskets done for the second time. Last time was 7 yrs ago. Truck now has 90K mi on it and I have had nothing but Matt's tunes on it since the head gaskets were done originally. I have only towed once and I put the 8K tow tune on for that trip.
ARP studs were used but heads were not decked then. OEM gaskets, done by Ford.
So a head gasket failures with ARP studs and doing everything else the FTE way?
New heads are decked and o-ringed. Planning to go a little more gentle with the tuning, but don't really want to. Driving it stock just sucks.
Ran fine, did the head gaskets ,egr delete, oil cooler and 12mm dummy plugs. Primed the fuel system, oil pressure looks good on the guage , spins fine but doesn't seem to be making any attempt at starting . Gave it a shot of quick start and it never so much as kicked. Everything looks good, nothing leaking and nothing obvious. To top it off we are without power after Hurricane Mathew left his mark.
View 14 RepliesI have a 2006 6.0 that i did head gaskets on about a year ago. While I was in there I put some new pistons a valves in as well. I finished doing the job and it started and ran great just smoking a little bit. Test drove it a couple of times and still seemed great but still smoking. (white smoke) about a week went by with me driving the truck then one day driving to work I parked it then all of a sudden the truck shut off like some one hit the key and wouldn't restart after that. Either doesn't work i put a ficm in it before the head gaskets went out. new HPOP before head gaskets. I get oil pressure in the dash but it takes a long time to build up. cranks like a dream but doesn't even try to fire.
View 14 RepliesJust bought a 2005 F250 PSD, got a smoking deal on it. It has 321k miles and has been very well taken care of however I do believe that it either needs a new oil cooler or has bad head gaskets. Pictured below you will see what the coolant looked like when I let the first batch lose. It does not seem foamy, which is interesting to me, however there is NO EGR to cause this soot.
About the truck:
- It was bulletproofed at 50k miles (EGR delete, ARP head studs, etc).
- There is no puking of coolant (drove it 100 miles from where I purchased it and nothing)
- When the truck is started you have to let it warm up for about 10 minutes,otherwise it seems to not have full power. (was going to reflash the ECU in hopes this repaired that problem).
Truck is a 2006 F-350 6.0, ARP studs, Ford Head Gaskets, Bullet Proof Diesel Oil Cooler Kit and EGR with an SCT tuner on tow mode.
Towing approx 15,000 pounds noticed truck started to lose power and misfire. Pulled over and noticed engine oil all over the driver side on engine, looks like it sprayed to top of engine as well. Oil on valve cover, FICM, exhaust manifold. I looked under the truck and saw that oil is all over bottom of the truck, differential covered in oil as well. Looks like blue smoke coming from tailpipe and smells of oil burning. Cannot tell where oil originated from.
I removed the EGR Valve, to see if there was moisture on the valve and when I looked into the intake manifold there is engine oil pooled in the bottom of the intake manifold and on the EGR Valve.
This is not dirty water from soot, it is oil. Truck is misfiring, with no codes being thrown. I noticed a small amount of white residue around the radiator cap however I had just filled up the reservoir, week prior. I unfortunately do not have gauges in the truck and rely on the factory gauges; coolant temps did not rise or move at all when this happened. I am not sure if I blew a head gasket, and really confused on how engine oil got into the intake manifold. I ran the engine with the air filter removed and can see blue smoke coming out of the CCV and oil in residue in front of the turbo inlet.
I have a 1995 aero with 4 wheel drive and a 4 liter. Lent it out and the engine was run without coolant. Pretty sure the head gaskets are blown. I found a replacement 4 liter from a 92 explorer and wondered if it would swap in. Will the bolt pattern match, computer, mounts,etc?
View 5 RepliesMy 2004 Excursion 6.0 4x4 is leaking oil around the gaskets. Does this usually just call for replacing the gaskets and is there anything that needs to be checked or upgraded while the engine is out? It looks like the engine needs to be taken totally out although I have heard it just has to be lifted a little.
View 14 RepliesIhave a 2008 E 350 6.0 , while driving i hit a small pothole no big deal the van stops running and coasts to the side of the road. get her towed. The dash lights show the PATS is engaged so it is no start no crank.
The 30 amp fuse PCM power relay is blown. when i replace it it blows as soon as i turn the key. im checking for wire chafing but so far have found none.
So I am not sure exactly what is going on with my truck. It is a 2004 F250 has a 6.0 L. Sometimes when I take off from a stop the truck has no power and blows some black smoke. Then the turbo kicks in and all is fine. It comes and goes when it pleases no matter the temperature. What started happening is when I drive it a steady pace on the highway sometimes the turbo gets quieter and louder and quieter and louder sometimes when it gets quieter I see a little bit of black coming out of the tailpipe. Sometimes it doesn't do it at all. Also sometimes when I let off the gas the truck sounds like it's trying to laugh at me like a wastegate is fluttering.
View 10 RepliesBlown fuse causing a lack of power to the OBD port?
I just got my Kiwi2 BT OBD2 adapter and was hoping to start diagnosing my truck, but the adapter won't power on while connected to the truck.
I pulled and visually inspected fuse #12, I also verified power to the cigarette lighter plug and the accessory 12v power outlet.
The adapter powered up with no problem when I connected to a co-worker's Tacoma.
Driving to work yesterday my engine shuttered and then shut off. The Display said low oil pressure and then powered down, all in about 15 seconds. Dealer called me today told me the engine is blown and is in the hands of Ford now. The only thing he told me was sit back and wait, I can not tell you how long it's going to be. but I am going to be screwed as far as work goes.
View 14 RepliesMy 2004 6.0 has lost some power and the head gasket is leaking into the coolant. How long can i continue to drive the truck before too much damage is done to the engine?
View 10 RepliesThis weekend while towing a light load I noticed my FWT and EOT starting to climb rapidly, EOT reached 260 FWT I think about 240. I exited the interstate to find I had a busted radiator hose. I replaced the hose and filled the system with distilled water, but didn't add antifreeze at this time. The system wasn't completely empty.
I noticed once back on the road my EOT seemed to be higher than normal but FWT seemed to be normal. Could the lack of antifreeze cause a greater delta between FWT and EOT? I have seen articles which state do not use Ford Premium Gold Coolant, but to use CAT EL-1 coolant instead. Which should I use?
So, I blew my head gasket and have been looking for what to replace it with. From what I've seen, just an OEM gasket would be best.? I'm also putting ARP studs in it, unless there's another brand I should put in it.
View 3 RepliesI Have two questions on installing studs. Does the 6 oclock dowel position really matter? To me it doesnt make much sense because the timing isnt changed with just studs so there should be no issue with valve clearance and such. Unless something isnt installed correctly.
Also what is the best way to clean the block? I thought Senior Master Tech on youtube had an interesting way with a piece of angle iron.
Any head handy that they could measure for me (or head gasket)? Wondering what the dimensions of the head surface is.
View 3 RepliesI just bought the batteries I was asking about in this posting. Bought them at auto zone on my lunch hour today, they swapped them out right there in the lot, no problems. Watched carefully to make sure terminals were not crossed, etc. When I came out of work a few hours later, the #20 fuse for door locks was blown. I chalked it up to the battery change, and put a new fuse back when I got home. I come out an hour later to leave, and the fuse is blown again. I have not replaced it again, need to go get more of the proper amp rating.
No other changes to the truck other than the battery replacement. And that's the only anomaly. No other problems, nothing. Getting ready to head cross-country on a skiing trip, this Friday, so there really is no time to get to the dealer to get this looked at.
Have a 2004 F350 dually diesel 6.0 - will now be replacing the passenger rear wheel seal for the third time in 8 months - replaced 12/2014 again in 6/2015 - took in for extensive engine pairs 7/8 got back 8/27 and have to replace the wheel seal again. Cannot figure out why blowing out so often - what to do to stop it from blowing out? Called the dealer and they were absolutely no support at all - mentioned something about a thicker seal?
View 10 Replies