Ford 6.0L Power Stroke Diesel :: Head Gasket Replacement?
Apr 8, 2016
So, I blew my head gasket and have been looking for what to replace it with. From what I've seen, just an OEM gasket would be best.? I'm also putting ARP studs in it, unless there's another brand I should put in it.
View 3 Replies
Advertisement
I'm going to be doing head gaskets on my 2006 F350 6.0. I know I need the head bolt tool and head lifting fixture. I have the tool to release the injector wiring plug from the head. Are there any other specialty tools I need? I saw in Hot Rod magazine a few months ago there was a new head gasket for the 6.0. Unfortunately I don't have the magazine anymore. I can't remember the brand of gasket. I know everyone in the past has said use OEM Ford head gaskets. Lastly, can I do the head gasket job and put studs in without pulling the cab or HVAC box?
View 7 Replies
Truck is a 2006 F-350 6.0, ARP studs, Ford Head Gaskets, Bullet Proof Diesel Oil Cooler Kit and EGR with an SCT tuner on tow mode.
Towing approx 15,000 pounds noticed truck started to lose power and misfire. Pulled over and noticed engine oil all over the driver side on engine, looks like it sprayed to top of engine as well. Oil on valve cover, FICM, exhaust manifold. I looked under the truck and saw that oil is all over bottom of the truck, differential covered in oil as well. Looks like blue smoke coming from tailpipe and smells of oil burning. Cannot tell where oil originated from.
I removed the EGR Valve, to see if there was moisture on the valve and when I looked into the intake manifold there is engine oil pooled in the bottom of the intake manifold and on the EGR Valve.
This is not dirty water from soot, it is oil. Truck is misfiring, with no codes being thrown. I noticed a small amount of white residue around the radiator cap however I had just filled up the reservoir, week prior. I unfortunately do not have gauges in the truck and rely on the factory gauges; coolant temps did not rise or move at all when this happened. I am not sure if I blew a head gasket, and really confused on how engine oil got into the intake manifold. I ran the engine with the air filter removed and can see blue smoke coming out of the CCV and oil in residue in front of the turbo inlet.
View 11 Replies
My 2004 6.0 has lost some power and the head gasket is leaking into the coolant. How long can i continue to drive the truck before too much damage is done to the engine?
View 10 Replies
I just did head studs, gaskets, egr delete, oil cooler, hpop, up pipes, exhaust, and turbo rebuild on my 03' 6.0. I started the truck and it ran kind of rough but I figured it was air in the oil. Then I heard a choppy sound from the tailpipe and my first thought was bent pushrod. I let the truck run for a couple of minutes while I looked and listened to the engine and it seemed alright but I shut it down to pull valve covers. I had a code for cylinder 5 contrabalance so I started there.
The pushrod was definitely bent so I ordered one and threw it in. The truck runs amazing now compared to anytime I have ever heard it run, and all rockers move as it looks like they should but I still do have popping through the intake. I took cylinder 5 pushrod back out and I think the gasket bent from when the pushrod bent the first time. Even though the rocker is moving I think the bent gasket is pushing the pushrod on the side of the lifter maybe? The guide in the gasket is folded over and I don't know how the hell to bend it back besides a screwdriver.
View 2 Replies
Early 04 but 06 motor, Coolant filter, BPD EGR cooler, Head studs. I did use the search tool, overloaded with EGR cooler leaks and head gasket failure in the results.
Noticed ECT Spiking 217 (EOT 187)as went to post office,10 min run time from a cold start. Checked Degas a bit low, did my business and went home. Got home ECT 223 EOT(221) zero coolant in Degas and notice this mess. as well as puddling up under radiator.
I left the truck running and added some water to the degas hoping I could spot the leak, no love.
On our trucks do we have a weep hole for the water pump? I didn't notice any water or stains around it or the pulley. Nothing around the hoses either... yet.
Once it cools I am going to pull the fan shroud and look for a possible hole in radiator. Are there any other suspect areas?
View 7 Replies
I LOVE my Super Duty and with only 15k on it (have a company truck) plan on keeping it for a long time. I've had an EGR Delete and new Oil Cooler along with some misc things done to the engine and turbo, about 6g's worth. Now my mechanic at NCB is telling me that the reason I'm loosing coolant is that my head gaskets are leaking. I'm looking at another 5-7 grand which is a no go for me. I'm thinking of doing the work myself, especially since I've seen where i don't have to remove the body to do it.
Okay, here is the question, I've been having a hard time finding a comprehensive list of the parts I should be getting to do the job. Looking for a list or link on what I need to do it correctly and anything I might want to do while my engine is apart so I don't have to do this again?
View 10 Replies
So I'll give a little history. Had blown head gaskets so I tackled that got it back together and now I can't get it to start. I have a monitor but it won't tell me if I have ficm sync. I have 1500 psi cop reading. I have spinning it over far 15 to 20 minutes. I'm using a bluetooth scanner and a app on my phone. I have no codes thrown or anything else. Do I keep cranking on it or am i missing something.
View 14 Replies
Vehicle 2007 Ford Explorer Sport Trac with 4.6L
Ok, just did a head gasket replacement. Everything is now hooked back up. Now when we try to restart the car, we get lights, but nothing from the starter. Also the OBDII code puller can't communicate with the car. Also the security light flashes very fast when you try to start.
View 9 Replies
I need walked through the take down to replace the head gasket on an 05 mountaineer with a 4.0. I've never worked on one of these so I don't even know. I havent even seen the engine to know where to start.
View 3 Replies
2007 Sports Trac .. Does the motor need to be removed to replace head gaskets? 4.0 sohc
View 1 Replies
I have a quick question, I just replaced the head gaskets on my 4.6 with 301,000 miles on it and now my battery only charges when you punch it and when you lift off the gas pedal, in town it does fine, but on drives 25 miles on the highway the battery guage goes to the line on the bottom. What could be causing that?
View 2 Replies
I am replacing the head gaskets on a 2006 Ford F250 6.0 .... I have heard that I should replace the head bolts with studs. Do I torque the studs just like the bolts?
View 5 Replies
I have a 2002 pontiac montana that needs the head gasket replace. Mileage is 152,000 miles with a v6 engine. I would like to get at least another 75,000 miles once the repair is done. Is it worth doing as alternative is to scrap the van and buy a new vehicle...
View 3 Replies
I have a 2007 Subaru Forester X Sport Model. I just passed 86,000 miles - much of that open road driving. My head gaskets need to be replaced. This seems somewhat early. I recently switched from using regular motor oil to a synthetic blend that the dealership suggested. Is there any history suggesting that switching lubricants might cause the head gaskets to deteriorate?
View 10 Replies
In my motor build I'm replacing the HPOP fittings in the head. Do these need any sort of thread locker to secure?
View 2 Replies
I recently replaced the head gasket on a 95 Geo Prizm. Now when I tried to start it, all I get is the starter clicking. I tried tapping the starter solenoid, to no effect. The only electrical that I messed with during the head gasket replacement was to disconnect the battery.
View 4 Replies
I have a 1997 Honda Civic that I was given by an elderly neighbor's daughter after the elderly lady went to the grocery and ended up 100 miles away when she could not figure out how to get home. The car was smogged at the beginning of the year but when I got it ran very rough and the temp went nearly to overheating on the drive home when I was stuck in stop and go traffic.I found the radiator fluid level low and an oily residue inside the radiator water bottle. I took it to a mechanic to check it out and was told it had a blown head gasket and maybe worse.
I am thinking of buying a rebuilt cylinder head and replacing it myself but I am not sure how to diagnose if any other damage could have been caused to the engine. It's hard to know but I am guessing that the engine was damaged during the 100 mile road trip due to low coolant level. It turns out short term memory loss was the diagnosis for my elderly neighbor. I filled the coolant level and ran the engine for a bit and the temp stayed normal but the rough running remains. The oil dip stick shows no signs of coolant in the oil and the coolant looks bright green when I looked in the radiator after topping it up with some water.
Any way to detect if I could be facing bigger issues like failed bearings? I am OK to do the head replacement but an engine replacement starts to get into the realm of what it would cost to get another car of the same age.
View 18 Replies
A 2007 Toyota Camry 2.4 was brought into the shop I work at smoking badly and running terrible. The car had been run hot because the radiator was busted and it blew the head gasket. So I pulled the head and sent if off to the machine shop to have it checked. They said it was badly warped across three cylinder and they resurfaced it.
Now I have everything re assembled, but it simply will not start. All the timing marks on the timing chain line up where they should be. All four coils are firing. Injectors wires pulse noid lights. A few times it has hit and sputtered like it was trying to start but never successfully does.
View 9 Replies
How much should it cost to have it replaced? car seems to be running just fine but leaking oil.
View 6 Replies
I'll start by saying that I have a 2004 GTI 1.8t. Picked the car up from a local junkyard around 2 months ago for a grand. They were unsure why it was running rough, so I took a chance and picked it up. Got it back to the house and the timing chain tensioner was shot. Ordered a new one up. Went to a friends house and he noticed it was producing some white smoke from the tail pipe and suggest I take a look into my head gasket. Replaced the head gasket about 2 weeks ago. Got everything buttoned back up and it smoked even worse.
Being my first head gasket change I accepted the fact that I may not have been thorough enough in my replacement and stripped her back down once again. Made sure I was extremely focused and replaced the head gasket again. I just got her back together and she is still smoking.
I know for a fact that coolant is getting into my pistons and causing my spark plugs to foul out. Too much moisture in the cylinder.
View 13 Replies