Ford 6.0L Power Stroke Diesel :: F250 - Brakes Locking Up As Soon As Starts The Truck
Jun 22, 2014
I'm posting this for my neighbor who has a F250 that's 8 years old. He has replaced many parts, engine from what I know but now when he starts the truck it starts fine but as soon as he starts the truck, the brakes lock up. He can't move it. He hasn't had the chance to move it because the brakes lock as soon as the truck starts. It starts fine and idles fine but can't move because the brakes are locked. Tomorrow the tow truck will haul it to the ford dealership so they can look at it and run the diagnosis computer on it.
View 4 Replies
Advertisement
I need the transmission speed sensor for my truck and I am getting a confusing array of Motorcraft and Ford part numbers. I have Motorcraft numbers DY1251 (Turbine Shaft Speed Sensor Assembly) and DY1229 (Transmission Speed Sensor). Not sure what the difference is between the two.
I've been having a recurring problem where, when my speedometer starts wavering, the truck will sometimes jerk, like maybe it's trying to down shift or a stumble of some sort. I've replaced the VSS in the rear diff (with Motorcraft) which cleared up the worst of it, but this problem still persists.
View 3 Replies
I was parking my truck and the brakes wouldn't depress and I almost crashed into another vehicle that was parked.
View 14 Replies
2004 F550 with a 6.0. I had to clean out my fuel tank, replace the HFCM and filter on top of the engine. When I start the truck it will run for 30 seconds or so, start running rough then die. I opened the cap on the fuel filter housing on top of the engine to make sure the fuel was getting there. I turned the key on and the fuel bowl quickly filled up.
After a short time however, the fuel drained out. To where I do not know. I don't think this is normal as every time I've changed the upper filter on a 6.0 it is always full of fuel. Why could this one be draining out and could that be the issue why the truck dies after starting and running for a short period of time. I changed the o-ring on the cap and the new HFCM was purchased from Ford.
View 13 Replies
Tires have less than 10,000 miles on them, and air pressure is within 2 lbs left to right side.
New calipers.
New soft lines.
New hard lines.
New pads.
New rotors.
New ball joints.
New tie rod ends and center link.
New front axle universals.
Brake fluid and all other parts are less than 6 months old. I can let go of the wheel and the truck tracks straight, 10mph to 100 mph. Whether I am going 10 mph, or 100 mph, when i first step on the brakes the truck jumps right. Needless to say, the faster i am going, the worse it jumps.
After first brake application, truck tracks straight. Let go of the wheel and it tracks straight from 100mph to a dead stop with brakes applied after the initial jump. Whether I am hard on the brakes or gentle, it does not pull at all. Only on the initial step on the brakes.I am at a loss as to what the heck is wrong with it.
View 14 Replies
So was sitting at an idle in park and truck starts knocking, horrific sound. So shut checked oil, good, went to work came out 8 hours later, started up still knocked. Pulled into drive hit the pedal, knock went away, stopped at red light, knock came back...... Truck has been parked for 3 days, still knocks at an idle but soon as tap the pedal and give fuel it goes away... Tried unplugging injectors one at a time to eliminate, still had knock.
2003 auto, 4wd, studded,deleted, coolant filter, sct with innovative tunes 108,000 miles.
View 12 Replies
I have an 03 f250 that i think is getting air in the fuel line when it sits. It turns over starts and immediately shuts off. Then i have to crank it for a minute or so before it will start. After that it is good all day. Next day it might sputter on start but stays on. More than a day it shuts off immediately and needs cranking for a minute...
View 13 Replies
I've got an '05 F-250 starts and dies numerous times, have to rev throttle to keep running then it stays running. I've replaced FICM, PCM, Eng. harness, IPR, CMP, what else is there to do?
View 3 Replies
I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.
My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.
I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???
IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.
ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts
ICP pressure Start 900+
Idle 830ish
Sync between CAMshaft and Crankshaft is 1 = good
Have not gotten fitting to do fuel pressure test yet.
View 14 Replies
My 05 F250 CC 4x4 had a problem where it was wondering to the right.
I had the front end checked out and they said everything was good and within spec but they discovered a bad tire (internal belt separation).
Had two new front tires installed/balanced and the problem seemed to go away for a few months.
Now the problem is back even with the new tires. Could the steering box cause this or is there something else I should be looking at?
View 2 Replies
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
View 8 Replies
So today on my way home from work. I got off at my exit and when I went to step on the gas I lost power and the truck wouldn't exceed 15 mph. It would just rev up and down. It was pouring white smoke from the tailpipe. At one point it went back to normal and started running fine for about 10 seconds. Then it went back to doing the same thing losing power and spitting smoke. I limped the truck into a parking lot and called a ride. I'm having a tow truck pick it up on Monday and take it to the dealership. Is this a head gasket issue? And I feel like it's going to be expensive. 2006 F250 6.0L .....
View 11 Replies
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 Replies
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 Replies
I have a 2006 F250 6.0L. Just had a used motor with 108k miles put in. Had the motor studded, fire ringed, new injectors, new glow plugs, new radiator fluid filter system installed, had egr delete done, ficm board replaced, fuel pump replaced, a few other small items replaced as well. The problem I'm having is the truck runs like it has a miss until it warms up.
After that, it runs fine. It takes about 10/15 miles of driving before it runs like it should. Letting it run in the driveway for 10/15 minutes to warm up doesn't make a difference. When the truck starts, it lopes at an idle for about 5 mins before turbo kicks in & starts whistling. When I start driving it shakes & feels like it has no power until it warms up. Then you'd never know anything was wrong. Put way too much $ into the truck so far and can't keep going.
View 7 Replies
I have a 2004 F250 with a 6.0l Diesel and a 5 speed automatic. The truck is 4 wheel drive. As far as I know it is completely stock and has 236,500 miles on it. I thought that I was having stiction issues because when the truck is cold and when driving ~55 mph (1500 rpm) in 6th, the truck shudders until ECT gets to about 150F. This is at a constant speed, when accelerating or decelerating it doesn't shudder. Today I held 40 mph (1500 rpm) in 5th and there was no shudder. I don't know the TFT the shudder goes away at because the epiphany about the transmission was today. Once warmed up there is no to very slight shudder and only around 55 mph (1500 rpm). Above or below that the shudder goes away.
View 11 Replies
I have a 2011 F250 6.7 4x4 CCLB. About 90k on the odometer.
Full flopro exhaust(no cat, no dpf) and a H&S tow tune. Otherwise stock.
8" lift and 37" toyo mt tires.
Anyways, I ran the truck in my first truck pull ever a few weeks ago. I pulled in 4wd high, rear locked, tow/haul mode, traction control off 2nd gear.
I wasn't able to pay super close attention to all of the stock gauges, but it didn't over heat and it didn't rev over 3000rpm. It was pulling like a freight train until the 125' mark and it just shut off. I thought something may have broken.... I put it in neutral, cycled the key and it started right back up....
Checked for anything obviously wrong, no fluids, all boots looked attached and fine. Nothing. Drive it home and haven't had a problem since. No CEL, no warning no anything. So why the truck may have stalled on me?
View 14 Replies
Have 65k now..OEM breaks. Never an issue.. going along today had to make a fast turn left into a parking area. Hit the brakes doing about 50 made the turn. Slowly found and kept rolling to a parking spot. Went to apply the brakes and found the pedal was rock hard. The truck kept rolling slowly. Pure luck I was were I was.. I tried to shut the truck down and restart. Still rock hard pedal in up position. No breaks.. not enough to stop at idle. Checked the brake fluid and it was fine. Went inside the store to grab the delivery and when I came back out I tried to work the pedal down.. I felt some give.. put it in reverse to check it out..(couldn't go ahead no room.) slowly the breaks came back. Has been fine since.. driving all over town today. No codes or engine lights.
View 14 Replies
I have an 03 6.0 F250. My truck started blowing fuse #45 and it would kill my gauges (fuel, oil, mph, rpm, temp, trans temp, and odometer) and I was just replacing the fuse and putting off the repair.
However, the most recent time my gauges blew, the fuse did not, and I put in a 20 amp fuse, in hopes that it would not blow so quickly, bad idea. So naturally, I ordered a new shift lever, in hopes that it would fix the gauges and I wouldn't have to deal with it anymore, but I think it was too late and something else needs to be replaced. What I could possibly have blown by having a larger fuse in there?
View 9 Replies
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
View 6 Replies
I have a friend with a 2012 F250. The truck has 100K miles and it does idle for extended periods. The other day his check engine light comes on so he took it the shop. They had not told him anything yet, but they did tell him that he had about a gallon to much oil. They said it was fuel.
View 7 Replies
