Ford 6.0L Power Stroke Diesel :: Exhaust Manifold Leak - Sounds Like Air Rushing Out From Driver Side Of Engine
Mar 22, 2017
So I started my truck this morning and it sounds like air rushing out from the driver side of the engine. I currently have my ICP unplugged due to a bad sensor, will be replacing it on Sat. Also I have been having an issue with my turbo but I don't think that it's related as I here the air rushing sound when at idle as well at when driving. It seems to be a bit louder when the engine is cold but I could also be crazy about that.
View 3 Replies
Advertisement
So ford is replacing 8 injectors for me and they found this. They are trying to tell me bad oil cooler but I do not believe it. What do you all think is the cause. I should also say that I had coolant in my drivers side exhaust manifold.
View 14 Replies
so i cant quite tell where its coming from, but here is a picture. it seems to be coming from just even with the drivers side exhaust manifold towards the back. from what i can see the top valley looks clean. it seems to only leak while its running. and it leaks quite a lot. its close to the bell housing so im guessing a rear main but i don't know. i hope its not!
View 14 Replies
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
View 14 Replies
I had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
View 14 Replies
I have developed a leak coming from the top, driver side, rear of my engine and I could not figure out where it was coming from. I took it to a reputable shop for diagnosis and they tell me that the rear leak is coming from the transmission lines.
The weird thing is I never thought the leak looked like ATF. They also told me that it looks like the stock radiator/cooler has been bypassed so I have no cooler.
Should I assume that the stock internal cooler failed and that is why the PO bypassed it? Also is there a decent write up on deleting these lines and running soft transmission lines to a aftermarket cooler?
View 5 Replies
I have a leak at the driver side exhaust manifold. Its a little tough getting at it to tell if its a lose bolt, crack or bad gasket. What would be the best way to get at this area? Should i remove the tire and wheel well or is their a better way. If i can get at it i may replace the manifold all together.
View 2 Replies
My 05 Gx has the infamous manifold exhaust leak on the driver side. I'm planing to change it myself I don't think it should be that tough.
View 2 Replies
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
View 14 Replies
I can't get my exhaust manifold bolts off. They are in bad shape. The 10mm is too loose and 3/8 just rounds. I have had the torches on them too! Can the bolts be cut off with a torch?? Haven't broken any. Can't get the bolt heads to move. It's an 04, original manifolds. I am working the driver's side. I can't figure this one out. How to get this manifold off?
View 4 Replies
How difficult is it to change the passenger exhaust manifold? I have just finished replacing the left exhaust manifold. The biggest issue was rusted fasteners and inexperience. Have torches. Any you tube videos show the left manifold being changed but not the right. I do not have a hoist and work in my driveway. Is the right side more difficult and should I leave it to someone with a hoist?
View 4 Replies
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 Replies
I have a family member that has a stock 2016 6.7 Auto F350 XL DRW that is less than a year old, has 85k on it and is developing an oil leak on the drivers side of the engine. What are the possible culprits and any pictures that I can forward to him of those places.
View 10 Replies
I have an air leak sound coming from I believe the driver side. Sounds like an air line from a compressor leaking. Could see anything obvious last night or hear well over engine. When driving it's pushing more air. Nothing looked/felt loose. Didn't find any air blowing were I could stick my hand in a hot engine. Doesn't seem to have performance issue, maybe a little more turbo delay.
View 3 Replies
My truck is running fine but it sounds like there is an air leak on the drivers side of the truck. When it first happened I was passing a car and it sounded like a vacuum hose come loose. It made a loud hissing sound. Now I have come to the conclusion it must be associated with the turbo. I don't hear the hiss unless I get into the truck and the turbo starts making boost. The more boost is made the louder the hissing sound is.
View 4 Replies
On Friday am I noticed a 6" sized puddle on the garage floor. Coolant leak on the drivers side coming off the frame. Dropped it off at the dealer on Sunday and today the tech tells me it was in fact a radiator leak and the new one will be here wed. They hope to have it buttoned late Wednesday. I am assuming all will be covered under warranty.
I have 23k miles logged and had just got home from a 1300 mile run pulling about 18k worth of hay and trailer. Truck performed flawlessly. Averaged 11mpg for the trip. I am hoping this is the first and last radiator replacement I have to go thru.
View 14 Replies
Earlier this week, I had the p1260 pop up. Then while driving to the beach, I had the p2290 pop up. I do not actually have a check engine light on, but used my torque app to find the codes. I have found a oil leak on the driver side coming from somewhere. I have a mishimoto thermostat coming in next week. I will try to collect parts needed for this repair. From my understanding, it's a hpop leak and the adrenaline and stc fitting should be my next move.
View 13 Replies
I have an oil leak on a 04 f250 6.0 stock. It has 292000 miles on her. It started as a few drips on the pavement about the size of a quarter and now has escalated to a steady trickle. It's on the driver's side in front of engine running down the corner of the block and dripping off the oil pan. I pulled intake plenum and everything and I thought it was coming out of the valve cover but now it looks like its just under the valve cover. It looks like its coming out of the front corner of the head. Its wet there and looks wet around the glow plugs. I cant run it now as I've drained the oil and coolant. I don't have a gauge or anything and its plain stock.
View 14 Replies
My truck just passed the 3 year/36k by 2 days! I got it on 8/4/10 but it only has 27,000 miles of course I just found a puddle of coolant under the right front drivers side. After a little reading, I guess this is common. Should I push for Ford to fix it or get an extended warranty and turn it in on that or... Aftermarket yet that isn't half plastic like this stock POS?
View 12 Replies
Attempting to take this on myself. My passenger side manifold was replaced a year ago.....BTW This damn truck - all stock - no modifications of any kind - just turned 100k miles. One owner - me.
So I have removed everything I think I need to to gain reasonable access including the fenderwell and all the intake tubes and battery and coolant reservoir. I want to use some heat and try not to break the bolts but there is a thin wiring harness just above the exhaust manifold. I can't find it in any diagrams on the ford parts site. It looks like the glow plug and injector harnesses are up above near the intake manifold but this one is down below all that. It connects to small rubber thing - 1 for each cylinder. There is nothing else electrical near it - everything else is up top.
Now my rant - look away if you are a die hard ford truck fan or 6.0L powerstroke fan.
So far I've had to replace both exhaust manifolds because they burned and rusted right through. New transmission cooler lines -yes - rusted through and cooler (because we couldn't get the lines off without destroying the cooler). Cat got clogged (that was fun to find and fix). All 4 front ball joints replaced. Transmission dip stick tube rusted through. Several brake lines had to be replaced due to rust. The air conditioner quit with about 80k miles. I haven't fixed that yet. My oil pan is rusting through and needs replacement. Friggin oil pan! I have never in my long life experienced that. I know of other diesel pickups that are older with far more miles that live in the northeast, used for plowing and never garaged that don't have their oil pans rusting through. Just had to change both power steering lines that go to the gearbox due to leak caused by rusting through. EGR needs to be cleaned or replaced almost as often as the oil need changing. This POS needs to be out of my life!
Too bad because if it was dependable and wasn't made out of the cheapest crappy metal Ford could find it would be a great truck. Rides and hauls great. Plows great. Good looking truck, too. Standard cab 8 foot bed. Dark green. Just can't keep doing this.
View 13 Replies
I have approximately 66,000 miles on my 2013 F250 truck and noticed a small drip from the front drivers side around 40,000 miles. That random drip is now a leak and the truck will be going into the shop to replace the Primary Radiator.
I absolutely love this truck, but what a disappointment that this isn't a recall. What scares me is that my buddy who has a 2014 F250 will be going in for his second primary radiator in 3 years of ownership.
View 14 Replies
