I just pulled the cab and did headgaskets, studs. I put everything back together and when I turn the key, nothing, no lights, zero.
I've checked all connections and batteries are good, checked all fuses, where to start with this?
If you have a blown head gasket on a 6.0, after the gaskets were removed would you be able to tell where the gasket failed?
Since the gaskets are metal or multilayer metal in some cases would you be unable to tell where the gasket failed or would it always be visible?
I just had headgaskets (oem) studs, egr delete,oil cooler done on my 06 plus water pump cause the gasket blew. I have a sct livewire hooked up monitoring everything and tonight i noticed that the eot and ect's were way off. fully warmed up and rolling 65 Anywhere from 40*-50* out it was eot-156 and ect-172. Degas bottle was at the normal level.
I am also having issues with the fuel gauge. Every now and then the gauge will go to E and the miles to E will display ---. Turn the truck off and back on it works again. I am half assuming its the plug on the sending unit or the sending unit itself.
So I am just wrapping up getting my head gaskets done for the second time. Last time was 7 yrs ago. Truck now has 90K mi on it and I have had nothing but Matt's tunes on it since the head gaskets were done originally. I have only towed once and I put the 8K tow tune on for that trip.
ARP studs were used but heads were not decked then. OEM gaskets, done by Ford.
So a head gasket failures with ARP studs and doing everything else the FTE way?
New heads are decked and o-ringed. Planning to go a little more gentle with the tuning, but don't really want to. Driving it stock just sucks.
Ran fine, did the head gaskets ,egr delete, oil cooler and 12mm dummy plugs. Primed the fuel system, oil pressure looks good on the guage , spins fine but doesn't seem to be making any attempt at starting . Gave it a shot of quick start and it never so much as kicked. Everything looks good, nothing leaking and nothing obvious. To top it off we are without power after Hurricane Mathew left his mark.
View 14 RepliesI have a 2006 6.0 that i did head gaskets on about a year ago. While I was in there I put some new pistons a valves in as well. I finished doing the job and it started and ran great just smoking a little bit. Test drove it a couple of times and still seemed great but still smoking. (white smoke) about a week went by with me driving the truck then one day driving to work I parked it then all of a sudden the truck shut off like some one hit the key and wouldn't restart after that. Either doesn't work i put a ficm in it before the head gaskets went out. new HPOP before head gaskets. I get oil pressure in the dash but it takes a long time to build up. cranks like a dream but doesn't even try to fire.
View 14 RepliesJust bought a 2005 F250 PSD, got a smoking deal on it. It has 321k miles and has been very well taken care of however I do believe that it either needs a new oil cooler or has bad head gaskets. Pictured below you will see what the coolant looked like when I let the first batch lose. It does not seem foamy, which is interesting to me, however there is NO EGR to cause this soot.
About the truck:
- It was bulletproofed at 50k miles (EGR delete, ARP head studs, etc).
- There is no puking of coolant (drove it 100 miles from where I purchased it and nothing)
- When the truck is started you have to let it warm up for about 10 minutes,otherwise it seems to not have full power. (was going to reflash the ECU in hopes this repaired that problem).
When the engine is working hard and the head (s) unseat, where does the coolant go, in the oil, to the atmosphere or both?
There are times when I am pulling heavy ( 18 to 20K+) pulling up a hill from a stop, and I can hear the engine working hard, then I later check the coolant level and it has drop.
Where did it go?
My 2004 Excursion 6.0 4x4 is leaking oil around the gaskets. Does this usually just call for replacing the gaskets and is there anything that needs to be checked or upgraded while the engine is out? It looks like the engine needs to be taken totally out although I have heard it just has to be lifted a little.
View 14 RepliesI can't seem to get my fog lights to work. i checked am both bulbs are good. I did pull out the headlight switch. I checked fuse 43 an its good. I popped dash out an checked wires to headlight switch an found the wire for the fog lights, yellow wire on my 05.
Its getting power when I pull the headlight switch out to turn on fog lights. Pulled plugs of of fog lights an getting no power to them.
They use to work. i put in some HID headlights an they still worked. then i put some led's in my instrument cluster an sometimes they would work an sometimes not. now they wont come on at all.
Is there a fuse or something to check? All other lights work, just book the running lights
2006 f250 4x4 CC
So my tail lights and license plate lights are not working. The head lights work also my gauge cluster lights are not working. Which fuse I should check. Or what it might be?
View 6 Replies2011 f350 king ranch... I have DRL, turn signals and tail lights. I have checked all fuses ( don't know if there's a relay) under hood and in cab. Still do not have any headlights, high or low beam nor do I have any fog Lights.
View 5 Repliesluckily about 5 minutes from home my trailer running lights AND the lights on my dump truck body stopped working. i assume they hooked the lights to my dump body to the trailer lights. i was towing an old trailer that has electrical issues so I'm sure that caused it. Under the hood there is a 30 amp fuse #26 that i think is the culprit. (All the other similar fuses are shiny and that one is kinda black). I've never bought fuses like this before, what type is it? it's a big square one. Are they available at auto zone? Does the whole thing pull out and do you need a special tool for it?
View 3 RepliesMy 2004 6.0 has lost some power and the head gasket is leaking into the coolant. How long can i continue to drive the truck before too much damage is done to the engine?
View 10 RepliesSo, I blew my head gasket and have been looking for what to replace it with. From what I've seen, just an OEM gasket would be best.? I'm also putting ARP studs in it, unless there's another brand I should put in it.
View 3 RepliesTruck is a 2006 F-350 6.0, ARP studs, Ford Head Gaskets, Bullet Proof Diesel Oil Cooler Kit and EGR with an SCT tuner on tow mode.
Towing approx 15,000 pounds noticed truck started to lose power and misfire. Pulled over and noticed engine oil all over the driver side on engine, looks like it sprayed to top of engine as well. Oil on valve cover, FICM, exhaust manifold. I looked under the truck and saw that oil is all over bottom of the truck, differential covered in oil as well. Looks like blue smoke coming from tailpipe and smells of oil burning. Cannot tell where oil originated from.
I removed the EGR Valve, to see if there was moisture on the valve and when I looked into the intake manifold there is engine oil pooled in the bottom of the intake manifold and on the EGR Valve.
This is not dirty water from soot, it is oil. Truck is misfiring, with no codes being thrown. I noticed a small amount of white residue around the radiator cap however I had just filled up the reservoir, week prior. I unfortunately do not have gauges in the truck and rely on the factory gauges; coolant temps did not rise or move at all when this happened. I am not sure if I blew a head gasket, and really confused on how engine oil got into the intake manifold. I ran the engine with the air filter removed and can see blue smoke coming out of the CCV and oil in residue in front of the turbo inlet.
I Have two questions on installing studs. Does the 6 oclock dowel position really matter? To me it doesnt make much sense because the timing isnt changed with just studs so there should be no issue with valve clearance and such. Unless something isnt installed correctly.
Also what is the best way to clean the block? I thought Senior Master Tech on youtube had an interesting way with a piece of angle iron.
Any head handy that they could measure for me (or head gasket)? Wondering what the dimensions of the head surface is.
View 3 RepliesSo I'll give a little history. Had blown head gaskets so I tackled that got it back together and now I can't get it to start. I have a monitor but it won't tell me if I have ficm sync. I have 1500 psi cop reading. I have spinning it over far 15 to 20 minutes. I'm using a bluetooth scanner and a app on my phone. I have no codes thrown or anything else. Do I keep cranking on it or am i missing something.
View 14 RepliesI have a "VAN" Ford E350 and I need to check push rod on cylinder 1 and 5 left bank, how to do this?
Is ok if I remove the ARP head stup then check push rod and then re torque the head stud?
Full Story here : [URL] ....