I've noticed it takes my truck much longer to start recently. I have 2 brand new interstate batteries, just changed both fuel filters and my truck still takes a good 10 seconds or more of spinning over to fire. Is this normal? I don't remember my truck doing this before, it usually fired right up even in winter. Could this be an injector or glow plug issue?
View 13 RepliesI just finished installing a new set of injectors, standpipes and the blue spring kit on our 2005 Excursion 6.0. The truck idles and runs much better but now it takes almost two seconds of cranking to start the engine. Cold and hot are the same and the length of time between shut down and start doesn't seem to matter either.
What to check? I am planning to check the ICP tonight when I get home. Could I have air trapped some where in the system? This is my first powerstroke so I don't know if this is a possibility.
When I start my truck it takes 30 seconds or so for the truck to start moving... especially when in reverse. If I give it some gas it doesn't take quite as long. I am not a transmission guy. I assume it has something to do with building pressure but I don't know what would be the cause. The fluid is full and looks good.
View 8 RepliesThis applies to a 2001 F-350 with 73,000 miles on the engine. Engine oil level is good, batteries charged, HPOP reservoir is full and passes Cody test with flying colors. Fuel pump runs for 20 seconds at key on. Start takes about 6 seconds. If I shut the key off and restart immediately it starts in under 2 seconds but if I wait about 30 seconds it's a 6 second start. Here is an AE that I ran on it, it has me stumped. FWIW it seems to start quicker when AE is hooked up. ?? An odd whir type of noise comes out from somewhere under the hood when I first turn the key on and when I clear the codes with AE.
View 14 RepliesWifes Escape with the 3.0 has been progressively getting harder to start. It spins over just fine, but now takes between 3 to 8 seconds to actually fire. In the last six months the alternator, spark plugs, air filter have all been replaced. Engine runs perfectly, never stalls and seems fine in every other way. I've cleaned the throttle body and the IAC is working fine.
Did some troubleshooting and sure enough, we are getting no spark for a few seconds and the engine runs fine when it finally gets spark. Would this be the crank position sensor? Cam position sensor causing this? Not sure what is supposed to happen during the starting sequence in regards to what sensors are in being read by the PCM and then enabling spark.
As would be expected things deteriorate on a 16-year-old truck. My alarm has, on a few occasions, decided to annoy anyone around by activating for no apparent reason. This has happened in various conditions (in the parking lot, in the driveway, right after I've driven it, or sitting half the night). I chalked it up to aging circuitry.
Now I've picked up something new. Over the last few weeks my truck may or may not arm. It seems to be a flip of the coin. I'll drive to the store and I push the button on my remote and the truck goes "beep"..."beep". 10 minutes later I drive home, park the truck, push the remote, and the truck goes "beep"...and that's it. My alarm light is blinking two quick flashes when this happens.
Since this has started my truck has begun randomly having a delayed start. I'll disarm the truck, turn the key, and nothing happens for about 1 second or so (seems longer) then the truck starts normally.
Both of these issues started pretty close to the same time. I would normally go straight for a starter issue but I don't know if these might be related. I'm the second owner so have absolutely no idea about the Ford anti-theft system, how it's connected, or what the blinking lights mean.
I'm considering disconnecting the anti-theft system to see if that makes a difference but, as stated, how it's connected, what I might disable, or how it works. Was there any documentation published on it?
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 RepliesGot up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
Had long start issues. Would turn over for 5 seconds - shut off- turn over for 5 seconds - shut off - third try on 4-5 seconds the low oil pressure would come up and HOP would fire injectors and start up.
Was not sure what was up, so look it to Ford. They did leak down test and found seal at the top of injector 4 was leaking. Replaced it and leak moved to other injector. Basically moving to the next weakest seal point. I told them to stop as i did not want to pay, parts, labour and shop time to replace all injectors, etc. They also said power across all injectors was good, but 3 & 7 were not contributing on cold start.
I drove it home and bought parts. New cups and seal for all 8 on fuel rail. New gasket kits for injectors. Plus 2 new injectors to replace 3 and 7.
Replaced injectors in 3 & 7 with the 2 remanufactured i bought. Replaced all cups and seals on fuel rails. So it has new injectors in 3, 4 & 7.
As for the other injectors i took the 5 of them right apart and cleaned them and re-assembled. Took about an hour per injector, took my time to get it right, just FYI. Went pretty good i thought. Seemed pretty straight forward actually.
Now no start - no high oil pressure at all. LOP comes up right away. Scanner shows no HOP no matter how long i crank it.
FICM power good, 47.5 - 48
shows FICM sync - YES
IPR sits at 14% and jumps to 84% on crank - starting, see photos below.
Scanner prior to crank
Scan during crank
Note zero IPC - PSI
Right now.... Got the valve cover off on passenger side. Cannot see oil squirting out the sides of any injectors, but line of sight is limited. Maybe need a small mirror to see in there. LOP comes up better than it has in years, but no HOP now. Before rebuild it seemed i had good HOP but low LOP.
I drove it home from Ford and into my garage, so i do not believe the HPOP crapped out sitting in the garage, so i am ruling that out as a fail, at this time.
Dummy plugs were replaced 5 years ago and o-rings looked decent.
Pulled the small plug screw at the top of the fuel rail. Cranked it until oil came out, bleeding air. then replaced the screw plug. Have not done that on drivers sideyet. Will try that tomorrow. However, think this is more than an air issue, as i have cranked it over plenty, unless i just have that much air.
Going to pull the valve cover on the Driver's side tomorrow. Then will have both covers off at same time to view all.
Noted that if i put compressed air into the screw hole on top of the fuel rail, i can hear air coming out from below the fuel rail. Nothing at the base or around injectors. Does not seem to be at the cups either.
Just wondering.... Buy applying air to those screw plug holes, is that the same as doing the air test at the sensor that pokes up through the valve cover.
With air pressure at these scew plugs on the fuel rail, should this be sealed and be air tight and hear no air leakage. Because it was not air tight on the drivers side before i closed that side up. I am curious about this.
I am assuming i still have a HOP leak. I do not think i have a failed HPOP. How to better chase a HOP leak?
Strange thing happened yesterday and again today. I have my compressor hooked up to up fitter #3 ,turned it on yesterday to fill the tank back up to 120psi. Before it filled up i shut the truck off to fuel up..but the compressor kept running for a few seconds after the truck was off. and today doing some running around the compressor turned on out of the blue when i was driving..but the switch was off.
The shut off switch (on the compressor itself) turns it on at around 90psi and shuts off at 120, but the thing filled my tank to 180 before i noticed it was on, pulled over to shut the truck off and again it ran for 10-15 seconds after the truck was off. I'm pretty confused. maybe it has something to do with the build up of snow under the truck, we just got 16" two days ago. but still when the up fitter is off shouldn't that cut the power from the accessory hooked up to it?
I have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 RepliesWhen taking off the 1-2 shift and the 2-3 shift the truck will go into a neutral state for 2-5 seconds. when this occurs, the rpms will rev since your foot is on the accelerator. Once you let off the accelerator the rpms come down and the gear will catch. I have had the truck in the shop a few times without any luck. part of the problem is no codes are thrown so the dealer has no clue what to look for. This is extremely dangerous when in my case i pull out on a 6 lane hwy with 55mph speed limit. Ford more or less said to pound salt until a code is thrown or until something else happens. this nearly caused a nasty wreck 2 weeks ago.
View 14 RepliesAlright, my 1999 7.3 keeps dying on me in the morning. About two weeks ago I noticed it started to have a weaker start up, even though it has two brand new batteries. Once it starts up, I get around the block and it dies there every time. Then I have to crank it for about 15 seconds for it to start again.
The crank gets faster and faster until it finally start, and the engine is very choppy, like its starving for fuel. After about ten seconds of that it return back to a smooth idle. I then take off, and about 50 yards later it does the same thing. After it does it the second time, the truck runs just fine for the rest of the day with no problems.
I have noticed that when if I turn the truck on and let it idle for 10 minutes first in the morning, it won't die on me. I replaced the camshaft position sensor thinking it was that, but it wasn't.
This morning I went out to start my truck. It cranked for about 15 seconds with no start. I set my TorquePro to monitor the IPR% and cranked again for about 10 seconds. The IPR% was about 83.7% with no start again. I went inside and searched for "crank no start" threads to see what else I needed to look at. I went back out and added HPOP to the TorquePro. Cranked for about 5 seconds, thinking I would get no start again, but it fired up. After start I was getting about 27% on the IPR and abour 537 on the HPOP. Drove to work with no problem.
Could this just be a fluke, or do I need to be concerned about it? I have a road trip coming up to Tennessee on Thursday. I did standpipes, dummy plugs, STC fittings, EGR delete, new oil cooler and upgrade to stainless steel IPR screen about a year ago.
So I just got torque pro set up and I have not looked at ICP and IPR since I had some work done. New oil cooler injectors and all that jazz
At a hot idle I am getting
580-590 psi ICP
And 22.8% IPR
Does this seem a little low or are these good numbers for a hot idle?
I brought my truck to ford because I thought I was having transmission issues, but they are telling me that my transmission is fine, that I need to replace my number 8 injector. None of these symptoms sound like injector issues:
-Shifting from park to reverse, takes a couple seconds to shift, then jumps.
-Coming to a very slow stop, truck is a little jumpy at around 2-3 mph
Dang, won't start again. My auction truck needed batteries, so I put mine in it and bought new ones for my work truck. Couple of days later, didn't start. Checked SG and I wasn't getting enough RPM. Jumped it and it fired right up. Replaced one of the new batteries and it's started fine the last few times, until just now, in the parking lot of the tire store.
The RPMs were weak - they'd go over 160 but then fall back to the 140s. I walked home and got my auction truck, jumped it, and it still doesn't start. Just spins. RPMs still fall back to the 140s after a few seconds of cranking, but they got as high as 220 so I don't think that is the problem. Fuel pump runs, the upper bowl is full, no bubbles. Oil pressure registers on the dash after a few seconds of cranking.
The last time, I wiggled some fuses and it started. Not this time. FICM at 48, ICP around 700 while cranking. Volts and IPV are good. FPW is 0, but I think that's right, until it cranks. Same with Sync - at 0 while cranking - does it ever go to 1 without starting?
It acts like it has in the past - cranking just fine but no start. And in the past, when it finally starts, it acts like nothing was ever wrong. I checked my IPR screen about a month ago after replacing it about 6 months ago when it didn't start. What am I missing? I'll go read some threads for clues.
After running perfectly fine all day my truck will seem to bog down and when I press the accelerator the reaction is extremely delayed and tons of black smoke will come out of the tail pipe before the truck actually gains power and takes off. The check engine light has been coming on but will turn itself off after the truck has been shutdown a few times....
View 10 RepliesI have a 2004 F250 Superduty with the 2003 6.0 Powerstroke inside of it. In the morning i can go out and start the truck perfectly fine starts up and runs like a champ, it will drive to any destination perfectly fine with no issues, ALTHOUGH .... once i reach where im going if i turn the truck off it will not start correctly. it cranks over and will start but sounds as if it is hydrolocking and in a matter of seconds kills itself. once it does this i have to let the truck sit for a minimum of 4-5 hours with the hood popped to allow motor to cool... as soon as its cooled completely i can start it and once again it runs perfectly fine until i turn it off again. if i leave it running at an idle it will sit and idle all day long and i can jump in and drive it fine. It just happens when it gets turned off.
View 5 RepliesI removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 Replies