Couple weeks ago fuel tank started coming apart clogged all filters. Replaced tank filters and fuel pump and blew out all of lines. Started and ran fine. Stays plugged in over night but now it'll crank but wont start. No codes showing up or anything...
View 1 RepliesA month ago I changed engine oil, oil filter and both fuel filters. All replacement filters are Motorcraft and my mileage is off a solid 2 mpg after the fuel filter replacement.
View 14 RepliesHow many miles should I go before changing fuel filters and air filter?
View 14 Replies2013 6.7 F350 13,500 miles... Changed the fuel filters and got them bled out and truck runs OK but have a whining noise from the engine compartment fuel filter area.
View 14 RepliesChanged the fuel filters. No issues in replacing.
Primed them by the book - key on 30 seconds 6 times
Now I have low pressure warning and reduced power.
All parts were FOMOCO...
Like usual, i have a problem that no one else has and it sounds like its something electrical/sensor/PCM related.
Every few mornings, ill go out to my truck and go to fire it up...and it'll just crank away. After i give up on cranking and shut the key off, go to try again, it fires up instantly, like nothing is wrong. Sometimes in the morning itll just have an extended crank but eventually start. Regardless...it always starts. Sometimes it cranks really strong the entire time, sometimes the crank gets weaker the longer you crank...i don't think its HPO related, but i definitely could be wrong.
Ficm voltage looks good KOEO, cranking and running. I had my batteries tested at ford a few weeks ago and they "said" they were good (motorcraft 850ccas). Alternator is strong. When cranking, ive seen the voltage drop anywhere from 10.2 to 9.4v. I never know when this is going to happen and i can't hook up AE every morning and sit and wait, but based on my scangauge, i see ICP shoot up to over 1500 as soon as it fires.
Only code I've gotten is P0148, which is fuel delivery error/engine speed higher than expected. I've gone ahead and replaced my camshaft position sensor with a ford sensor a few days ago...it hasn't done a no-start yet, but it did do an extended crank. I think my next stop is PCM replacement...
New alternator, fairly new batteries....after sitting 5 days or more, it cranks but no start.....put on charger for four hours, it fires right up...
Voltage on the multimeter shows 12.45 on both batteries......could there be something drawing down the amps? If so how do I find it?
Ive had my 2011 for 20 months. I have 7,300 miles. I know the manual states changing around 22k but do you think time is a factor as well? I wont hit 22k for two years. Truck will be 3.5 yrs old. Should I just change them at 10k and see how they look? Don't want to waste the money either if its unnecessary. I use it 50/50 towing/unloaded.
View 8 Replies2007 6.0 my dash lights will flicker when the key is turned on and the truck wil crank but won't start, but when the lights stop flickering truck starts .. How to fix the flickering dash light?
View 2 RepliesMy truck usually starts up great, but every so often it takes 3 to 4 long cranks before it will start. By long cranks I mean more than 4 or 5 seconds of turnover. Seems to be no real rhyme or reason to this. It does it engine cold or hot. I have iPhone engine monitor app and numbers seem fine. BTW it's a 2005.
View 12 RepliesI got a 2003 6.0 powerstroke cranks but wont start once it gets hot let it sit for a couple of hours and it fires right up already replaced high pressure pump no leaks visible and when running its great will run till run till fuel runs out. what to check?
View 3 RepliesI changed both fuel filters on my 2015 F350 6.7 I turn the key online for 30 seconds then turned it off for total of 6 times when to start the truck this morning after driving it yesterday and it took a little bit longer to turn over before it finally did, did I miss something up that I do something wrong. So I let my truck warm up this morning after going to start it at took a little bit longer for it to turn over I turned it off wait a few seconds then turned it back on and she started up how she used to perfectly fine does it just need to go through a drive cycle. This is the second fuel filter replacement nothing was wrong with the other ones I'm at 40000 miles now ... also it seems like the fuel filter on the frame rail is louder if you put the filter in upside down on that will it fit stupid question I'm sure I did it right but thought I'd ask before I tear it apart....
View 14 RepliesI drove the truck Sunday to 3 different places, parked it around 3:00 pm. Went to take it to work the next morning and it just cranked with no start. I pulled the codes as I have an edge insight. I got a P2614 code so I figured it was the cam sensor. We after some reading to what everyone had to say I checked to see if I had RPM when I got home and I did so that put me back to having no clue. I took as many readings as I could to see if any one might see something that I am not.
ICP psi 1280 cranking 23 key on
IPR 41% cranking 14 key on
IPW ms 0.00 cranking and key on
Fuel Pressure 63.1 cranking
ICP voltage 1.6 cranking .3 key on
Mass Air flow 8.3-10.7 cranking 0.00 key on
Engine RPM 166-205 cranking
FICM 47.0-47.5
2011 F250 6.7 Had the fuel filters changed by the dealer today. No noticeable sounds when I left the dealership, & no fuel stops on the way home (120 miles one way). When I got home, before shutting off the truck, I heard a loud groaning/singing from inside the truck. With the truck still running, I get out, & the groaning/singing is very pronounced....never heard this before & appears to be emanating from the fuel filter underneath the truck.
I turned the truck off, then turned the key back to the position that the fuel pump turns on, and wow, the pump is very loud. Definitely something going on because when I turn the key for the pump to turn on but not start the truck, I can feel the vibrations of the pump working from inside the truck and when listening from underneath the truck, it is very loud. Before today, the truck never made this noise and never heard the pump before.
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 RepliesI have a 2006 6.0 that i did head gaskets on about a year ago. While I was in there I put some new pistons a valves in as well. I finished doing the job and it started and ran great just smoking a little bit. Test drove it a couple of times and still seemed great but still smoking. (white smoke) about a week went by with me driving the truck then one day driving to work I parked it then all of a sudden the truck shut off like some one hit the key and wouldn't restart after that. Either doesn't work i put a ficm in it before the head gaskets went out. new HPOP before head gaskets. I get oil pressure in the dash but it takes a long time to build up. cranks like a dream but doesn't even try to fire.
View 14 RepliesI have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 RepliesI just replaced my oil cooler and 500miles later its clogged again. Delta reached 40F.. No fun... I replaced it with the factory ford cooler and installed the coolant filter but I guess when I did the first flush I missed sum gunk.
So my question to you PROs, should I reflush/restore again then replace the cooler? OR Go with one of these??
- Coolant-to-Liquid Oil Coolers
- IPR External Oil Cooler Kit for Ford 6.0 Powerstroke
The budget is tight, but I gotta keep the truck going.
My 2011 has 62k miles and has been throwing P0401 codes, which results in losing power. I assume the EGR cooler is clogged. So I went to the dealership to see if it's covered, and was told there's no warranty coverage.
I would rather blockoff the EGR cooler than repair it. I would also like the extra performance from a tuner like the MiniMaxx. I do prefer the stock exhaust and not real excited about the drone/smell that comes with deleted DPF.
Will I have issues if it's tuned with the EGR blocked off, and stock exhaust? Or am I better off doing a full delete at this point?
I have a 2004 F250 Superduty with the 2003 6.0 Powerstroke inside of it. In the morning i can go out and start the truck perfectly fine starts up and runs like a champ, it will drive to any destination perfectly fine with no issues, ALTHOUGH .... once i reach where im going if i turn the truck off it will not start correctly. it cranks over and will start but sounds as if it is hydrolocking and in a matter of seconds kills itself. once it does this i have to let the truck sit for a minimum of 4-5 hours with the hood popped to allow motor to cool... as soon as its cooled completely i can start it and once again it runs perfectly fine until i turn it off again. if i leave it running at an idle it will sit and idle all day long and i can jump in and drive it fine. It just happens when it gets turned off.
View 5 Replies2007 6.0l cranks but no start. Read all the forums and I think I performed all the checks. Getting a ficm/ cam sensor/crank sensor no sync. I'm also getting 84.70% at the ipr while cranking. Do I have multiple problems? Watched videos on either the ficm or ipr percentage but not one that had both problems. Getting injector clatter and fuel pump runs. Didn't see anything obvious with the harness.
View 14 Replies