What the coolant temp should be around after plugging in the block heater overnight? Not looking for an exact measurement since this can be affected by OAT and the length of time it has been plugged in. But when it's -15 to -20F this weekend I was wondering what to expect.
View 13 Replies I wanted to specifically ask about the block heater though. Since I bought this truck I never was able to start the truck without plugging it in. Now that it's not running I'm thinking much more about the block heater.
Is 56 too low for this old truck to start? What temp should a block heater have the oil temp as seen by AE be?
I live in the southwest so it's not very cold here. plugging in the heater was even required in the summer unless the truck had been running. What kinds of engine trouble would require being plugged in in warm conditions?
I didn't have time to trouble shoot but heres my problem. I plugged my 2016 6.7L in last night and when I checked it this morning the block was still ice cold. I didn't have time to investigate but i did make sure i had power up to the truck. And i noticed there's a connector just after the truck plug as well.
View 14 RepliesDoes the block heater come with some kind of a cord? I found the Box Link stuff under the back seat finally, the dealer said the block heater should be under there too? But it aint there?
View 6 RepliesDon't drive the truck but once a week but since its gotten colder here than usual is been harder to start when cold. Of-course I go thru the glow plug wait and then it kinda stumbles when its about to start. I do it again and most of the time is starts but seems rough for a few seconds. Once the truck is warm, no more problems starting.
I'm wondering if I have a glow plug gone bad and that cylinder is not warming up for me. Today I plugged in the block heater for maybe 2 hours and it started first time. Also, if just leave the block heater plugged in for long periods of time.. would it get to hot?? and wonder how expensive that is, most heater are costly to run. I have a timer but just wondering.
Well, I swapped a 2011 F250 SC for an F350 CC and I really enjoy driving it. 300 miles on the clock. My old 250 had the block heater and the pigtail to plug it in was low in front of the radiator. This truck also has the block heater, but I cannot find the pigtail to plug it in. In 2016 where Ford hid it at?
View 14 RepliesOk, is it possible to blow a fuze if the block heater is still plugged in when starting? Almost did this the other day and wondered if its possible to cause a short or something.
View 6 Repliesmy egr delete j pipe orings give me trouble and i replaced but broke a bolt, now i think that big donut oring is leaking, i was reading you can put a 3/4 freeze plug in to eliminate any coolant into the intake, where does the freeze plug go,front cover or intake and does coolant still pass thru the j pipe?
View 7 RepliesSeen a coolant leak near the back of the block? I did an oil change and noticed coolant on the bell housing.
View 7 RepliesEver since having the EGR delete done, the oil temp has been LOWER than the coolant temp. I am assuming this is bad info from the sending unit? They are reading with in a degree of each other at start up, but when at operating temp the gauge will read lower. Before the EGR delete I had a delta of about 4-7* oil hotter than coolant.
View 1 RepliesI am getting tired of my EGR valve plugging up and disabling my Excursion, I pulled the valve and installed an EGR plug. The valve is still plugged in and sitting on the intake.
After a couple of drive cycles the CEL came on for "low EGR flow".... yeah, you don't say.
Anyhow, what's the easiest way to turn this thing off? I don't want to crank up HP with a "tuner", but if that's what it takes. Can I turn off the CEL and retain the factory performance?
I've been searching for a while now but have not found an exact match to my problem.
So, Yesterday I was pulling a large load home (15K lbs) over flat land/small rolling hills and I experienced a coolant temp spike. And I am trying to figure out what caused it. I was traveling 65 mph about 2k rpm and 20lbs of boost, I was motioning the ECT, EOT, TFT, and Fan Speed via my scanguage and 99% of the time the ECT was in the 209-220 range, once it got up to 220 the fan would come on and the ECT would drop to 209 ish pretty quickly.
However, twice the ECT shot up from 215 ish to 240 within seconds then the dash indicator said check coolant temp then the fan came on and cooled it down to 200 within seconds, I did lose about 1/2 gal of coolant. So today I'm going to get a new degas cap (still OEM original) and continue to monitor the situation.
My EOT ECT delta has been a constant 10-13 degrees for the 3 years i've been monitoring it so i believe my oil cooler is still functions within spec and all my cold soak temps are within a degree or two for various ambient temps (20 -80) so all my sensors should be good.
Also, tonight I'm going to pull the EGR valve and check if there is any coolant in the intake, but if there is not, where should I start looking and what should I start worrying about e.g. head gaskets?
This is the only 6.0 I have owned. My tranny temp (with the Torque Pro) is pretty much always the same as my ECT. My ECT will move, and less than 2 seconds later, the tranny will move to the same temp. Is this normal? I was expecting lower tranny temps, but maybe it should be the same because of sharing the radiator.
View 11 RepliesThe truck has been just terrific, mostly used for towing our travel trailer. Earlier this year i developed a leak and lost 3 quarts of oil before I caught it. I would think with 15 quarts in her this shouldn't have been too big a deal. However, I am now experiencing 10-15 degree swings between ECT and EOT. Before I give the particulars, yes, I have had three new thermostats, two Ford and one brand X.
Anyway, coolant temps are 184-200 depending upon load, terrain, etc. At the same time, oil temps run 205-230. There is no oil cooler to get plugged up. She's got 120K on the clock, doesn't burn oil, no disappearing coolant. I am concerned about blowing a head gasket or other serious damage at these temps, but don't have a clue where to start? Yes, the fan does come on, but still this seems plenty hot.
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 RepliesI have an 04 F350 and I was wondering if the fan is supposed to be locked up when the A/C is on. In max A/C with the fan on 3 it's barely keeping cool in the 95 degree heat we have been having. If I rev the engine I don't hear the fan noise like I do when the coolant temp hits 218 and the fan roars. Freon was replaced several months ago, along with receiver/dryer and orifice tube when I did the HG's. The A/C shop drew a vacume and did not find any leaks.
View 7 RepliesI have a 2006 350. When I am pulling my camp trailer (about 12,500 lbs) up a grade I hear a fan or blower turn on and I get a high pitched squeal. It will also have a beep and my in dash display will say high engine temp. I have a bullydog pmt programmer (i tow with it in stock mode) the display will show my coolant temp at about 180 degrees. If I pull over and let it idle for about 2 minutes the warning clears and the temp gauge returns to normal. the display reads about 180 degrees the whole time this goes on. I know the engine is not over heating so why do i get this warning and squeal?
View 4 RepliesI don't think that my block heater is working correctly if not at all.
View 14 RepliesI can't get my truck to start. The block heater isn't working and I previously put flush and water in it, intending to drive it and flush it directly after. Well I never really could drive it and now it won't start again. The weather is going to turn off cold, around zero this weekend. I need to know how to keep the block from freezing and cracking!
View 11 RepliesDoing oil cooler. Block heater plug is very tight. Is it reversed threaten?
View 1 RepliesWhen the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.