Adding a coolant pressure gauge to truck? There are some expensive kits but considering I already have a gauge that would work, could I just buy a 5v sending unit for fuel pressure or oil pressure and have it work?
View 14 RepliesWhat is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 RepliesI bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
Looking for pics of where/how they mounted their fuel pressure gauge? I'm getting ready to install one.
View 11 RepliesLast week I was driving on the highway and noticed the oil pressure gauge showed no pressure. Limped a half mile to the mother-in-laws and called for a tow. As my truck was pulled onto the flatbed I could see oil all over the bottom of the engine, tranny, rear end, etc. Turned out to be a bad oil pressure sender, which was leaking enough oil to blow the plug off the top of it.
I replaced the sensor, cleaned the engine and under-carriage, checked oil level (which showed no loss of oil) and drove around for a week without an oil pressure gauge while I waited for a new pigtail. Put the pigtail in yesterday and drove it today for the first time since. Gauge was working, got to the bank and it was reading zero pressure again. Limped home and watched the gauge go back up quickly and then back down. This happened twice and was showing pressure when I shut it off. Checked under hood, no oil leaks and plug is still secure.
I'm getting pretty comfortable with these forums now. Not sure if this is in the right section, but even if it was, I'm not sure how to find the right one. I recently purchased Bullet Proof Diesel's Air-to-Oil oil cooler along with the BPD oil filtration. I've already drained the oil, but do I need to drain the coolant as well? I have read of people doing a complete flush before even installing a new oil cooler (OEM oil cooler). That way once it is installed, it doesn't have all the grit and sand pumping through it right off the bat. But does it matter with BPD's system? Should I go ahead and drain the coolant completely before beginning this job?
View 10 RepliesWell got home and the front of the truck was covered in coolant. I must have driven 2 hrs after I noticed no coolant pressure, but temperature was great so figured it was another crappy cap. Looking to get a quick turnaround. Need to go out of town for work Saturday so I have this week to get it done.
Just put a stock unit back in? I don't think I need to do anything else in that area. Belt/pulleys/radiator all done last spring.
My buddy install a BPD air/oil oil cooler in his 2003 F250 last week and now there is coolant pouring out the tail pipe. I haven't seen it but he tells me there is quite a bit coming out. It wasn't doing this before we installed the BPD oil cooler. Normally I would say bad EGR cooler but his EGR is deleted. This is the 3rd BPD cooler I've put in and this is the first time I've had any issues after the install. The install went smooth other than we broke the radiator and had to install a new one. I feel bad cause I'm hoping it wasn't something I caused but I just can't think of anything I did during this install that would cause coolant to be getting into the exhaust. He just had it towed to the local Ford dealership.
View 3 RepliesI currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 RepliesHave 2006 Ford Power stroke with 6.0 in it.. Just started doing this ... When Im driving the oil pressure gauge is fine and motor sound fine, but sometime when I come to a stop sign the oil gauge will drop all the way down to zero, the motor still runs fine and has plenty of oil in it. After I press on the fuel pedal to raise the RPMS just a couple the gauge goes back up. the odometer will all so blank out and it will flash "read gauges" when this occurs,, its driving me crazy and not sure where to start..
View 14 RepliesOK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
I finally received all the parts needed for installing my fuel pressure gauge, but I am wondering if I am going to need a schrader valve on my fuel pressure line going to the sending unit, or if I am going to be safe with just doing a 6 time cycle of the fuel pump like we do when we change out the fuel filters. Seems like that should work for getting the air out of the fuel lines, same concept I would think.
View 14 RepliesWell, I was cruising down the highway @70MPH and notice the fuel pressure gauge dropped down to 50 then back to 65. Kept watching the gauge and it would swing back and forth from 55 to 65.
Got off the highway. Nailed it at the light and watched the gauge drop to 53 and swing back to 65. Fuel pressure is not steady either. It swings back and forth from 52 to 65. Thinking the pump is on its her last legs? Truck got 194K on her.
Couple of years ago I installed a fuel pressure gauge. I wrapped the fittings with teflon tape. Well within about a year it started leaking. So I shopped around and used Permatex Permashield fuel resistant sealant on the fittings. It says diesel resistant on the package. Couple months later leaking again. So I take it apart again, clean every fitting and follow the instructions to the letter. Well its leaking again. What will resist diesel fuel under 55 psi pressure. All the fittings seem to be pipe thread.
View 7 RepliesI'm trying to chase down a couple of issues and I need to be able to monitor the coolant (and oil) temps. I've downloaded the manual and the specific 6.0 X Gauge commands but don't see the coolant temps listed.
View 8 RepliesI just did a pressure check on the cooling system on my 04 6 liter. It reached 16lbs towing an enclosed trailer and into a strong head wind. I was just wondering what's the Normal pressure suppose to be, or is there a Normal pressure. I'm using the new style cap with the larger spring in it and it didn't kick any coolant out.
View 14 RepliesI recently had an upper radiator hose bust and ever since I have been having a slight water leak. It appeared to be coming from between the layers of rubber on the new hose which I replaced twice since the incident. Both hoses had water seeping from the same location. This afternoon I plan on doing a pressure test on the cooling system to diagnose where the water may be coming from.
My question is could a loss of pressure cause larger than normal Oil and Water deltas? If I have to replace the radiator is there a particular manufacturer or type I should avoid? Should I try to get a factory replacement from Ford or would an Autoparts unit be sufficient? The original is still in the truck now with 286,000 miles on it.
Im lost here, my 6.0 is building coolant pressure on start up, and the temperature is not overheating. I cant tell if the pressure is staying high while driving, but its blowing coolant passed the cap. Thermostat? The truck was on a coolant pressure tester for 24 hours and never lost a pound of pressure.
View 14 RepliesOK so 2006 f550 6.0
If I want to monitor fuel pressure with a gauge in cab while running all the time... (not just testing) can I purchase one of the secondary fuel filter caps that have a port in the top and connect the sensor to this to run or is there a better way? (Or is that not going to work)
Cap I am talking about is something like this
[URL]
(I know this is a combo kit but they do sell the fuel only) But since it has a threaded port in the top I could connect the fuel pressure sensor to that and go from there correct? Would that give accurate readings?
Just changed the fuel filter in my '04 6.0, no issues worked just like normal, filter primed truck started, great. Well now my fuel pressure gauge is reading dead 0, I know that can't be right because the truck is running, but noticed my fuel mileage seems about 2 mpg lower all of a sudden. Had R&R Injectors installed about 40k ago, figure it's just a bad gauge but wanted to check and see before messing with the frickin wiring. Also, have had a lot of pressure buildup in the coolant tank, has had head gaskets and studs, anything else it could be besides head gaskets? Have had a lot of wiring issues with this truck from the previous owner....
View 14 RepliesBought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 Replies