Ford 6.0L Power Stroke Diesel :: Cold Start Blue Smoke Blowing Until Warms Up And Accelerate
Dec 6, 2016
I have a 07 6.0 powerstroke, I had 2 bad injectors so I replaced all of them with reman's. I had a problem with them coming loose. the first time this happened it hydrolocked the motor, number 8 cylinder. so I pulled all the injectors and replaced all the seals and washers and torqued them down a little more than spec like 27 lbs. it runs great and starts great even at 25 degrees but I noticed this morning that when starting it up after it sits (cold) it blows blueish smoke until late it warms up and I accelerate. is this normal? should I check fuel filters? oil in fuel?
View 14 Replies
Advertisement
05, 170k miles. Studded and egr delete but I don't have paperwork on either. Got a pretty good deal on the truck but I have a few questions..
It runs and starts great, warm and cold, with only a little blue smoke on cold startup. but every now and then when idling (say at a stoplight) the engine gets noticeably rougher, not terrible. No smoke. Goes away after 5-10 seconds.
When I remove the oil cap, there is a "puffing" blow by, not constant, and its not enough to blow the cap off if I set it on backwards. Just puffing.
This may be related, but I pulled the starter wire off the drivers side and touched it to the battery to hear how it cranks, and there is a noticeable blip in the cranking, its not 100% smooth.
Don't think I am losing any coolant. Runs great, getting 15MPG. No CEL. I went and had a relative comp. check done, cylinder 7 is the problem. We both are leaning toward there being a valve problem So I pulled the valve cover, now I have a few questions.
1. When I crank the engine over without starting, I can hear a "pfft....pfft....pfft" chug of air every revolution. I pulled the cover to see if I had a obvious rocker problem, but can't see anything because the oil rail is in the way. I'm guessing this air puff is sign of a valve problem?
2. When the truck is running, there is a small, steady stream of oil running down the rail and dripping onto the valve cover mating surface of the head, I think it was at every injector, definitely 2 of them. Was getting dark, so hard to see. Is this normal, or do I have a leak? Truck has updated dummy plugs.
My next step is probably going to be pull the rail, see if there is a obvious problem, then pull the head. And tips for me? Planning on having the HVAC evacuated then pulling the airbox.
View 9 Replies
2004 f350 4x4 sc dually 130K mi. Cranked truck this morning @ 18*F. Truck not plugged in but regular quick smooth startup. Noticed light blue smoke with normal condensation exhaust for about 5 seconds, then normal condensation exhaust for about 30 seconds. Drove truck at normal operating temps with 5* deltas. To my knowledge, truck has original turbo (Garrett), never been removed or cleaned by me. VGT at startup 70-72, running after warmup mid 50's. Is this a symptom of needing to replace turbo seal, and thorough cleaning while off?
View 1 Replies
My truck has been having this issue pretty much since I have had it, but it seems to be getting worse, or so I think.
When the truck is cold, it does not want to move very well. Like it's missing, and it does this until it gets warmer. Also, I have puffs of blue smoke come out the tailpipe when this occurs with it cold.
Injectors? Injector o-rings? Stiction?
FICM volts are good at 46.5v-48v when cranking.
View 6 Replies
Got a 2002 7.3 F-350 with 300,000 miles and for the last couple of years I've been getting blue smoke on cold morning start ups and its been gradually getting worse, it clears up after about 30 seconds and all is normal,No loss of performance, Oil consumption is minor, however I hate a vehicle that blue smokes, I'm guessing my issue is valve seals are worn, I was wondering if it is possible to replace the seals while the heads are on the engine? and was also wondering how much time it would take to fix? as i would have to have it professionally done. I know its hard to guess a time frame and everyone is different. Sounds like textbook valve seals to me but is there anything else I should check first?
View 14 Replies
I have a 04 f350 with 175k on it. At around 160k it had new head gaskets, 2-reman heads, egr delete, new oil cooler and it is studded and tuned with SCT and custom tunes.
Since after the head gasket change it seemed to have started blowing a little smoke on the cold starts mainly. In cold weather the starts seem to be harder or slower also. Now for the last 6k-8k miles there is a little smoke at a cold start. But if the motor is warm and it sits for a bit maybe 10 min or less it blows a nice puff of blue smoke or burnt oil.
The smell of burnt oil is mainly on hot starts not cold starts. It does not burn oil running. It will dump some black smoke under acceleration or load. Could this be an injector problem? Or something else? Can't figure it out.
View 5 Replies
My 04 6.0h started puffing bluish colored smoke typically only when I was accelerating. After a short amount of time I noticed it was smoking quite a bit when cold and until it had fully warmed up. I took it to the repair shop and they pulled it apart saying the turbo seal had failed and the turbo was full of oil. I purchased a new Garret PowerMax and had it put it in.
I picked up my truck and of course it was still smoking when cold. After it warmed up nothing, just like before. Since I just put a new turbo in I am worried this one will be ruined as well since the same condition exist. My mechanic said I need to run the truck for few days before the oil would get cleared out which had accumulated in the system. Am I mistaken in thinking that if it was residual oil burning that it would be more likely to do smoke when warm as opposed to when cold?
Since the turbo and seal have now been replaced what else should I look for to cure my blue smoke blues?
View 2 Replies
I have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
View 14 Replies
01 7.3 247k.
Yesterday went to get on the freeway I looked back and saw a cloud of what looked like blue smoke. I'm in northern Utah and it's cold but the truck runs fine, I haven't noticed any change in performance. Turbo still builds boost. I pulled the fuel filter cap last night to check fuel color and it was clean.
I do have the CCV mod done. I also pulled to IC Pipe off the turbo and there was a little oil in there but not much, should there be any at all with the CCV mod? Where to start.
View 14 Replies
Started today. 2004 with 235k miles. Owned for last 10k miles. Engine was recently studded, has egr delete and ccv bypass. Runs and starts fine. New Ford oil cooler too. Checked for codes. None for misfires, perdel are reading 0.
If it sits, on start up clear exhaust, as it warms, more blue smoke. Smells like oil not diesel.
Researched before asking and found leaking turbo seals can cause this. So we pulled the intercooler tube in front of the engine going to the intake expecting to find oil residue. Nice and dry. Was this the correct one to look at?
When we got the truck we had the dealer do a relative compression test and was within limits, it did need 1 injector that we replaced. What would be the next logical place to look?
Couple more points:
- Just changed oil last week, checked today, it was slightly over full.
- Coolant is fresh and has not changed level since we got it.
- Pulled fuel filter to see if any oil, but it was nice and clean.
View 11 Replies
two days ago i noticed First start in the morning the truck billows out blue smoke. In mean is enough that looks like an old 2 stroke dirt bike. Quite alarming. I've had HHS in for 4300 miles or so. I hope I did not mess the engine up by towing With the HHS in there. The injectors have been getting loud an indication that i need to change the oil again. The truck always gets louder when nearing oil change time. It reminds me of an old chevy with bad valve seals. Would turbo seals just go. The smoke goes away after driving maybe 2 min well i can't see it while driving. Truck runs smooth doesn't stutter or miss. It has been acting like the stiction is happening upon first starting after sitting for 6+ hours.
View 14 Replies
I noticed a few puffs of blue smoke a while back as well as oil at the seam of the exhaust tubing. I attributed it to bad turbo oil seals and proceeded to rebuild the turbo. Changed oil at the same time from T6 to T5, 15-40. The blue smoke is quite a bit less, but still shows at idle and not all the time.
First start up of the day, slight haze. I leave the house when the oil temp gets above 100 and drive easy until it gets to 160. I will get a pretty good train of smoke until the oil temp gets above 180 at every stop while I'm idling. When the oil temp gets above 180, it will only smoke every 3rd or 4th stop at idle. If I hold the brake and get the RPM's over 1,000, the smoke dramatically decreases, if not completely dissipates.
I do have the CCV rerouted and am wondering if it is affecting the operation of the engine.
View 9 Replies
2005 F250, 6.0, 60K miles, recently (within last 1K miles) had ARP studs, EGR delete and new oil cooler installed. Shortly after (5-6 weeks later) I noticed blue smoke under any load (taking off from red light, backing up) but not at idle or startup. Was using the "Performance" SCT canned tune after the stud install, but had the "65HP Tow" canned tune installed when I first noticed the smoke and now back to stock after noticed the smoke as a precaution. Everything else original except FICM, filters and batteries and use 5w40 Mobil 1 since new.
View 14 Replies
2006 overheats and starts blowing white smoke, smells like antifreeze, added 2 gals of water to make it 1 mile home. Smokes on the way @195 temp and when I shut it off it smokes out tailpipe for another 3 min. Smells like the head gaskets just went, what should I check? The eot and ect have been 10 deg or less.
This has 225,000 miles on it ran great before this, so would it be stupid too not get a redone set of heads while I'm doing the gaskets and studs?
I was thinking of getting heads from here, UCF Machine Shop - Precision machining, engine rebuilding and more. Cummins + Ford Rebuild Specialist. And a Sinister Diesel Complete Solution For Ford Powerstroke 2003-2007 6.0L. Are these the right places to deal with or should I look elsewhere?
View 14 Replies
Recently since the weather has been cold. between 0-30 degrees or so. My 2002 7.3 with 161k on it is smoking a decent amount i think. far more than i ever remember it smoking thats for sure! anyways its a combination of blue and white smoke and it doesnt last long when the truck starts maybe 1 minute and the smoke stops.
But I also notice when i rev the truck maybe around 1200 rpms the engine shakes very bad. so i was thinking maybe a glow plug went bad making the engine seem like its missing. but even when its warm i rev it up to 1200 and i still feel the engine shake slightly. Maybe im just being picky when its warm? I need to test the glow plugs and go from there but i want opinions about that issue. the truck sits for 4 hour periods and every time i start it i have smoke. I will pay attention tomorrow morning if it smokes after being plugged in all night and post my findings.
My other issue and this typically happens when its below 20. sometimes i will go to accelerate after coming to a complete stop and the truck kinda has a very weak rev to it then just takes off like the tps took a break on me. sometimes i have had it jerk the truck when the throttle catches and other times it creeps at first then takes off like a boost of power.
lastly and this little issue happens most noticeable at 35 mph. i feel a surging im thinking this is related to the tps but i put the truck on cruise control and i still feel the surging. maybe this ties into my second issue? bad TC? ive plugged in my scanner and the only thing jumping out at me is the icp hunts about 100 psi or more at idle. i plan on doing a WOT test on the HPOP, ICP and IPR tomorrow and see if maybe this is just a weak hpop causing my issues.
Repairs i have done:
new 8th injector and all new injector seals about 25k miles ago.
new ipr
new icp
have CCV mod done and 4 inch turbo back exhaust
new map sensor
cleaned out the EBP sensor and tube but that was probably 40 or 50k ago now.
gray cps and i cant remember when i put that on.
gutted the EBPV
bellowed up pipes
no tunes the truck is factory as far as that goes.
View 11 Replies
Replaced stock turbo on my 04 f350 zf6 with a newer stock turbo from an 05 6.0 excursion with a wicked wheel. Truck never smoked before ever for any reason. Now with the new turbo the truck puffs out white and blue smoke when turbo is spooling up in 1st 2nd and 3rd gear but once turbo is spoiled up no smoke at all. 4th and 5th no smoke at all. What could be my issue? Truck runs great no sputtering or missing or anything. I rebuilt injectors about two months ago so those are good.
View 2 Replies
I have a 2006 F350 6.0 diesel with 110K miles. it takes me about 10 tries to get the engine to start. When it finally starts there is a lot of smoke and engine runs really bad. This isn't the case if I have the engine warmer plugged in. After warm up the engine runs pretty good.
My engine light comes on sometimes and will go out other times. I have tried sever attempts at adding injector cleaner with no results. Am weary about taking it to Ford for an analysis. Where to start with repairs? I did take it to Orielly auto and had the engine checked on their scanner. Approximately two pages of possible repairs come up.
View 3 Replies
2004 f250 6.0, 173k miles. I just had the head studs done and a new head due to a crack in one head, I got it back 3 days ago and she was running great. I towed my landscape trailer yesterday full of mulch and only went about 5 miles with the load, after the job driving to another one I noticed it sounded like it was missing at idle with a small amount of white smoke. Drove it home let it sit overnight, started it up this morning and a cloud of white/ blue smoke and a horrible rough idle. Smoke does not stop.
View 10 Replies
2007 F350 CCLB, Still stock, 130k miles. SCT Tuner for towing and MPG (canned tunes).. I am new to the diesel world so just making sure.
Since we started getting colder mornings I have noticed a small amount of white, or blueish white smoke on start up for about 5 secs or so. Last week in Montana I did notice the light smoke for about 5 secs then looked like vapor for about 1 min (was about 30 degrees out)
Only during the first start of the day on cooler mornings (45 and under) have i noticed it, nothing while driving, no knocks or hard start, no codes. I am about due for an oil change (Delo in there right now but switching to syn), and do have the canned tow tune from SCT on there. Anything I should have checked or should check, I am decent with wrench.
Also I have noticed the blue sleeve that goes to the front of turbo coming from the front of the truck (maybe the cooler?), kinda looks like rubber gets a slightly dirty coating to it, not sure if normal or related.
View 1 Replies
I was towing my camper uphill and my 03 6.0 started missing and blowing black kid smoke. Next thing I know I hear a loud pop and steam is coming from under the hood and the truck dies. I pull over and discover the degas lid is stuck on and the bottle came apart at the the seam and the truck will not start. 6.0 with 120k miles
View 1 Replies
I just got a 2006 ford F250 lariat fx4,and it's already at the shop.. when cold start it has some white smoke, but once I get up to highway speeds the truck jerks and bucks. turbo is putting out normal boost. I've changed oil and filters along with fuel filters. also put on a new serpentine belt and pulley, air filter and have everything cleaned real good. the truck is acting like it's starving for fuel. FICM or injectors ?
View 14 Replies
