Ford 6.0L Power Stroke Diesel :: Codes P2285 And P2287 - ICP Circuit Low And Intermittent
Aug 7, 2017
The other day my 07 power troke threw codes p2285 and p2287- ICP circuit low and ICP circuit intermittent. The trucks idle was revving up or bouncing around every so often, not consistently.
I did a visual inspection of both the sensor and pigtail checking for oil but it looks to me like everything is clean and oil free (see pictures). When I unplugged the connector the trucks idol smoothed out and everything ran great!
My questions is what does this indicate? Does this mean my ICP sensor is bad, my pigtail is bad, or there is a short in the harness somewhere?
View 1 Replies
Advertisement
2004 Excursion 6.0L .... Recently after a 200 mile trip through the mountains running good, I get home and the next day it idles down the driveway at a high idle and after a few minutes seems to run better but within 5 miles the CEL comes on and throws P2287 - intermittent injection pressure control circuit. I cleared the code, ran around town again and the light came on again same code. I'm getting appropriate ICP-voltage and pressure readings. I took it home sat overnight and thought I would pull the ICP sensor.
I replaced the ICP sensor less than 6 months/5,000 miles ago. I also changed out the main engine harness at the same time. I looked at ICP sensor and it looks clean. Started the truck and tried the scientific wiggle test while running and monitoring ICP-voltage. Started at the sensor bending and wiggling back to FICM. No fluctuation in voltage. Ran the truck around town, 20 miles and no light. Yesterday we made the same 200 mile trip over the mountains, seemed to run strong. In town this morning within 5 miles the CEL is back on and the only code is P2287.
My Ford powertrain diagnostics manual doesn't have the P2287 code in it for troubleshooting. Should I go after the FICM, and how do U test that if so? I'm currently that 200 mile drive from home and don't want to damage anything more.
View 8 Replies
So yet another crank no start. Truck is an 03 55k miles The guy I bought the truck off of told me the turbo had been reconditioned about 1000 miles ago. Drove the truck another 1000 miles or so and now having issues. I went to start truck up and noticed it took awhile longer than normal to start up and when it did finally kick over, truck and no power at all. Would idle a bit rough sounded like no turbo spool at all when given throttle. Shut the truck off right and hooked up scangauge to it went to start it and nothing.
Did throw p2285 code ICP low circuit
Values read on scangauge are as follows:
FICM Main Power 48.0V
FICM Logic Power 10-8V
FICM sync is good
ICP Pressure 1540psi on crank
IPR duty cycle 14.8% Key on engine off/48.8% while cranking
At a bit of a loss as to where to look next, would really like to troubleshoot down to the right fix instead of just throwing parts at it. Have read after sitting the turbos tend to stick and need cleaned or replaced. After being cleaned only a few thousand miles could it be stuck again? Seems like I have spark, fuel, oil just acts like its not getting any air.
View 13 Replies
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
View 14 Replies
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 Replies
I have a 2007 f250 and got a check engine code icp circuit intermittent and to what I know icp sensor should be on the valve cover on the passenger side but it's not I bought the truck few months ago could it be that they swapped the engine for an early 6.0 or is there any other place for the icp sensor???
View 7 Replies
Just got back from the beach yesterday. On the way back I noticed the check engine light on and read the codes. It listed 4 codes, P0671,P0672, P0677 and P0678. From what I can find, Cylinder 1, 2, 7 and 8 have the glow plug circuit open. Truck ran fine and didn't miss a beat. Ambient temp was around 80 when we started up the truck so I guess diesel plugs are not to crucial for that temp. I did notice when driving back the Vbatt would jump from 12.2v at1854 RPM (34 MPH) and 13.8v at 1652 (57 MPH).
Would bad batteries or low batteries cause this type of problem? This may be wishful thinking on my part. I have tested the batts with a DMM and they are at 12.3v. I took them out and charged them but they always go down to 12.3v. FMP is 47.5v to 48.5v. It seems suspect that all four glow plugs would be bad so I assume it could be the harness. What are some ways I can test to verify where the problems come from.First thing I would do is get two new batteries as these are still under warranty.
View 3 Replies
So i just finished putting in new high pressure oil rail cup seals in and a new #2 injector. Truck was running great for about 5 miles and then just shut off. When I had it towed home I plugged in the super chips tuner "no tunes installed" and I have a p0460, p0463, p2290, p2291. I also have a #7 glow plug circuit failure Ive been a little neglectful in getting done.
View 6 Replies
I have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...
View 5 Replies
I have an emissions test coming up. I have 3 P codes that I'd like to eliminate before then. I don't want to "fix" the issues they are telling me about. Just make the codes go away. I know why they're there I just need to get rid of them.
What I have coming up is:
P0475 Exhaust Pressure Circuit Valve (result of EBPV delete)
P0541 Intake air heater A circuit low (result of aih delete)
P0640 Intake air heater control circuit (also result of aih delete)
What resistors I'll need and where to put them in?
View 12 Replies
So I was have a problem the other day with code p2285 did some more checking and found an hpo system leak. Bad injector o ring. I have fixed that. But now when I got it all put back together and went to start it up now have no crank at all, the wrench light is coming on, when I hook up my scangauge it will not connect (so I can't get any readings or codes) I have checked all the fuses that have to do the the ignition system.
They all seem fine. I can get it to crank if I jump the starter wire to the battery. I really need to get this figured out my mini Cooper is waiting for a new clutch to get here and with my truck down I can't get to my job sites next week. I don't know of its just a coincidence or not but while trying to get he truck to start my batteries got drained so got them charged and one was bad (it's less then a year old).
View 14 Replies
So my 04 f350 was running fine good power and everything till I shut it off a couple days ago and now when it is cold it fires right up but when the truck warms up it just cranks and cranks .... only code I throwing is p2285
Key on engine off
Ipr-14.8
Icp-0
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine running
Ipr-33.5
Ficm main power-48.0
Ficm logistics-12.5
Icp-875
I thought I fixed it before but I was sadly mistaken replaced the ICP and IPR...
View 14 Replies
Wife just pulled in said your trucks running rough. Right out the gate went out Checked ICPV its at 0 KOEO... Noticed a CEL P2285...
ICPV seams to be Jumping all around at Idle...
it stutters and smooth's out some I believe its going into default mode...
its acting different then last time the ICP went south thinking a wire is shorted or that's my guess ...
is it just me or do Vehicles seem to break down more when its Cold...
View 12 Replies
Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 Replies
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 Replies
i have a 2007 f350 6.0 and it was running fine. I parked it in my driveway for a couple of months and then went down one day to start it. The first day it started but the second day i went down it wouldn't start. it would crank but wouldn't fire up. I changed the oil, repaired the FICM and still got nothing. Then i took a generic scanner and got the code p2285. I replace the ICP but still no start. I have also changed both batteries. I'm not getting any codes right now either. What is going on?It has around 229,000 miles
View 11 Replies
Truck has performed flawlessly during that time period. Early build 2003 CC SB 4wd King Ranch truck 94,000 miles I purchased new in 2003. Good batteries. Bone stock except for superchips tune.
First sign of trouble: Two weeks ago CEL came on, P2285 Injector Control Pressure Circuit Low, as soon as truck was started after sitting unused for about a month. Bought new sensor, haven't installed it yet (early model sensor located under turbo on rear of engine and a real pain to change). Truck still started fine and ran fine. Dreading the ICP sensor install, I continued to drive the truck. Drove truck 5 miles to get tractor fuel. Got fuel, started truck and drove away. Got 200ft and truck died. I changed secondary filter under hood, turned key on and let pump cycle about 4 times. Truck started. Cleared codes. No longer have CEL. Drove 5 miles home, shut truck off and no start.
Troubleshooting: Changed primary filter under truck. Really cruddy (probably 80,000 mi on it). I cleaned inside filter housing thoroughly. I had to cycle pump KOEO about 6 times before it started. Shut off and immediately tried to start. No start. Ran pump KOEO about 30 seconds. Started. Shut off and same result. I then drove truck 4 miles driving both normal and WOT. No problems, no smoke, no CEL, ran perfectly normal. Shut off, no start until cycling pump KOEO for about 30 seconds. No codes set.
I then removed cap from secondary filter and checked for trash. Fuel and bowl were clean. I did notice fuel drained completely from bowl in about 5 minutes. I reinstalled filter and put pressure gauge on housing.
Fuel pressure readings: KOEO 55psi after about 3 seconds. Engine running 55psi. Turn key off and pressure instantly drops to 25psi, then bleeds off to zero over about a 3 minute time period. Does this seem normal?
Questions: Could the clogged fuel filters cause the p2285 code to set? Could the HPOP system have developed a leak and cause these symptoms?
Could an injector leak cause these symptoms and engine still run ok?
Action Plan: Install new ICP sensor. Do bubble test to check for injector compression leak. Install Blue Spring mod. Waiting on parts. Possibly buy scanner which will read HPOP output etc. Any recommendations here?
View 14 Replies
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
View 7 Replies
Stuck turbo and high deltas so I replaced the oil cooler, coolant, thermostat, rebuilt turbo. Etc etc. Now I'm getting p2284/p2285 intermittently. Upon inspection ICP looks great at idle and 2500. IPR at hot idle is 20.9 but when you run it up to 2500, it drops to 14.7 and after a few seconds hpop at idle jumps to 875 and I get the p2284/2285. Bad IPR?
View 14 Replies
I have a 2005 F550 with a 6.0. Recently I have had issues with a long crank before starting at times but once it started there were no issues driving. Yesterday it started up in the morning, made a few stops then it wouldn't start at all. Cranked strong but no start. Had it towed back, sat for an hour or two now it starts again. Put a gauge on it and all readings are good. Did have a P2285 code which the ICP sensor. I do suspect there could be an issue with the egr cooler as it needs coolant occasionally. Could that have anything to do with the no start? Truck has started fine today. Why start sometimes then not?
View 11 Replies
2006 F350 6.0 throwing code P0480 and I'm having a hard time figuring anything out pertaining to my truck. Trying to figure out what exactly it is and how to fix it myself.
View 3 Replies
