Ford 6.0L Power Stroke Diesel :: Code P0299 Appears On Cold First Start Of Day
Jul 1, 2015
Can a leaking Y Pipe throw a P0299? Dealership says that is my problem. My MAP at idle is 14.4 EBP is 17 - 18. At 60mph MAP is 20 EBP is 26-28. Boost is 10-20 .. Truck drives great no apparent issue. P0299 only code and appears when cold first start of day. If I clear it it goes away for the rest of the day and only comes back occasionally. Twice in 5 days only at cold start. 2005 F350, 100% stock, Ford filters all. Scan guage 2 for readings....
View 10 Replies
Advertisement
At 65 mph, egt was running between 1050-1150, turbo at 13-14 psi, rpm 2300. Code p0299 pops up. Before this the turbo would spool up to 28 psi going up hills. After it would not go over 16 and sounded funny. Truck is a 2005 excursion 4x4 with just under 200k miles . Trailer is about 10k pounds. No tuner. What do I need to be looking into? Is this too much for the truck to handle?
View 8 Replies
I just got back from a trip across the state to see the Miami boat show! Truck was running just fine on the trip over, EOT/ECT delta around 9* (seems a little high to me, Im hoping because im running 35's, but can someone back me up on this?)
On the trip back, cruising at 70, I noticed the check engine light went on... I didn't have it under heavy throttle or obscure circumstances... My ScanGauge 2 showed that I had a P0299, which as Ive read means something relating to underboost?
I cleared the code. And the CEL never showed again in the last 100 miles... Could this just be a quirk? Or should I be more worried about it?
View 14 Replies
I'm having a little trouble with my 05 Excursion 6.0L .... We took off camping the other day pulling our 30' camper and the engine light came on pretty much as soon as we hit the highways. I checked my Dash boss and it came up as P0299 under boost condition. The truck never skipped a beat. The boost gauge never dropped and it seemed to have lots of power. Actually I've noticed too much boost while pulling. It's climbed up to 36psi before and was still climbing when I backed off the throttle. I'm thinking the turbo is fine but not sure what to check next.
View 7 Replies
2011 Ford f350 6.7 diesel ... Is this a problem we need to have fixed?
View 2 Replies
I am fairly new to working on diesel engines. I was towing a camp trailer and got a P0299, Turbo Charger Underboost engine code. I never gotten any other codes other than this one when towing. I decided to pull the turbo and clean the vanes. Everything seemed to go back together good but now I hear what sounds like an air leak coming from the turbo area. The boots on the intercooler pipe are in good shape, I only loosened the clamps at the intercooler and the turbo. Left the boots on the pipe. I have tightened the clamps around the exhaust pipe connections with no change. I also seem to get a slower response from the turbo and possibly not as much psi as normal (according to dashboard gauge). I have driven the truck five or ten miles trying to work the turbo and have not gotten any engine codes to this point.
View 7 Replies
Last night when I was towing my son's Ranger home - somebody stole all his gas & he thought the fuel pump quit - heard a pop and the truck started running like crap. Thought I had blown the CAC boot loose but that wasn't the case. As it turns out, the tube for the EBP sensor came off from the manifold.
I had taken it loose about a year ago to clean it out. I guess I didn't tighten it well enough. Truck blew black smoke, lost boost, and filled the cab with exhaust fumes. Easy enough fix, kind of hard to diagnose because that's not expected. Just throwing it out the for somebody's future search.
View 1 Replies
What to do 2011 F550 RampTruck 11,850 miles on it the vehicle has been back to the dealer 5 times for the same trouble code P0299. After the last time it was in they had it for 2 weeks seemed to be fixed. Last week one of my drivers was towing a Chevy S10 50 or so miles and heard a very faint ticking like a stone in the tire that got instantly worse and before he could pull over started rapping and stalled out. We towed it back to the dealer they removed the Cab disassembled the engine and found a "blown piston" is there quote. What should we do about this problem the dealer is supposedly fighting with Ford and Ford doesn't want to put in a new engine.They want to fix it instead....
View 12 Replies
I just got a new 2006 E-350 van about 4 months a go (my previous 2004 got scraped - found out the fuel line leaving the secondary filter into the engine with clogged with bits of paper (wtf?)... after I decided salvaged it for parts for my new van...).
New van drives beautifully in the last 4 months without problem, but shut down on me on the highway yesterday. No strange noise or anything when it went out. I managed to coast safely to the side of the highway. Unfortunately, I cannot seem to start the truck again and had it towed home. It cranks, but doesn't start.
I have a scan gauge ii this time and it shows the following:
KOEO:
FICM ~48.5V
ICP 0
IPR 14.8%
Sync 0
Cranking:
FICM ~48.5V
ICP ~8PSI
IPR 84.7%
Sync 1
I still have a P0299 and P2262 check engine code from 2 days previous to the above, but this doesn't seem to be related to the no-start conditioning (both turbo related)
So, pretty much, I'm looking at a very low ICP. Some research indicates this is is due to a bad HPOP, bad STC fitting, or a massive leak. Given the really low ICP, can I rule out the STC fitting and leak? Looks like only the LPOP is providing pressure. Is there anyway to tell if the HPOP is dead or not once I remove it?
Anything I should shot-gun replace first? I have a bunch of salvaged parts from my old van in my garage, which doesn't include the HPOP unfortunately.
View 14 Replies
This morning when attempting a cold start of my 05 6.0, it would not start was noticeably harder cranking. I had no CEL. I checked my scan Guage and the volts were 13.4 and fcm main power was 48.4. I checked and I had a p0405 code. What could be going on? I read that it can be a stuck or bad EGR valve? Could it be battery related?
View 9 Replies
My '05 Excursion recently started having rough idle and some loping when started cold. It seems to run good and idles pretty good when it warms up. I'm also getting a P0488 code (EGR Throttle Control Circuit A Range/Performance). I do have a BPD EGR and I don't recall if that would throw a code alone? I'm taking a trip next week and want to get it straightened out. Does it sound like an EGR valve issue?
I also thought about a battery issue, I know that can cause weird problems. I have Duralast batteries and they always seem to fail at about 2-3 years. I took it in and they say it tested good but I'm not always sure with them. Long story, but when cranking for longer than normal, the cranking power would drop quite a bit. Checked battery and had some corrosion. Cleaned and upon further inspection, the positive post is a bit eroded at the base and sunken in. The voltage was about 12.35 after sitting all night, a couple of the cells were reading lower than the others (about 50%, other 75%) when checked specific gravity. I tested voltage after batteries had been in the truck overnight, then unhooked from truck when testing.
I also thought about a glow plug/harness issue. The truck cranks for awhile before starting, 5-6 seconds sometimes, but not all the time. It starts up pretty quickly when warm. That's been going on for some time. Anyway, I will try to get a video of the rough start after cools down.
View 6 Replies
So last night wife texts me pict of dash with CEL lit up... She was on the way home with horse in tow from a short haul to a nearby riding area. Truck has been in this service for more than a month and also sitting a lot. It has extremely low miles and wife tows horse with a soft pedal Always. I do try and take it out and exercise it, but that has been at least a couple months now.
Checked codes and ignoring a bunch of soft and repeat codes, got:
Current: P0299 - which is under/over boost usually, right?
Pending: P0478 - EBP high
So idled truck and all realtime info looked pretty normal, I think EBP was around 19, I realized I'm not watching Baro, I'll add that. Turbo was cleaned about 5K miles, but several years ago.
Was going to: clear codes, unhook trailer and take truck for a good drive, including some WOT romps and see what happens...? Or? I could set up data logging for boost, baro, ebp, rpm, and ?, prior to the drive... I guess eventually your "turn" comes up...
View 14 Replies
OK, long story short. I had P2284 code on my scan gauge after replacing the oil cooler. I contributed it to air in the oil system. Sure enough, a few days of hard driving and the code went away.
Now a week later, I fired up my truck on a cold start yesterday morning. It's not that cold here(low 40's in the morning), but the oil started off at about 50F. Correspondingly, ICP at is higher, at around 1000(it's like this every morning until oil warms up). I usually let it warm up a tad before driving but yesterday I didn't, and hit the gas pedal a little hard once and the truck started acting like it does when you get this code.
Sure enough, check scan gauge and the code is there. I drive home(about 15 minutes). A half hour later I start the truck up, check codes, and it's back to normal. Of course, oil temps were higher and ICP in the normal range between 580-590.
So is this normal? Since it doesn't trigger a CEL I assume it's more of a system parameters code? Only other thing I can think of, if this isn't normal, is a mucked up IPR screen from when I installed my BPD oil cooler.
View 13 Replies
2003, not deleted, everything was stock except for he put a Bully Dog on it with can tunes. Died on him was replaced ICP started up ran horrible was throwing different injector codes, IPR was at 84% at idle, plus had a lot of pressure on degas bottle.
Just finished studding, deleting, oil cooler, ICP, and injectors. She started up fairly easy, only to have the IPR still at 84%, ICP bouncing between 670s to 790s this just after start up from the work. Truck still runs horrible and still throwing #5 injector code also using AE and injector 5 wont Buzz. So, would be safe to say Injector harness and IPR sensor?
View 8 Replies
2012 F250 Superduty Lariat, 6.7 L.... While driving the cold air filter came loose and threw a CEL, code 2074. Corrected that issue, but CEL came back. Codes of 2074 and 2074pd. Cleaned both MAP and MAF and codes came back. Replaced both MAP and MAF and codes came back after about 20 miles. What are the next steps?
View 1 Replies
Well.. my truck has been running great for the past few years. This morning I went to start it and all it does is cranks and cranks.. no start not even a sputter.. I use the torque app and noticed the HPOP was over 900 psi during cranking and ICP volts were .8 volts. FICM was 48.5 and around 47 during cranking. I even unplugged the ICP connector and got the same results.. just cranks and no start. i noticed while it cranks i don't get any white "smoke" coming out of the tail pipe I even sniffed in there and I don't smell any diesel at all.
I pulled the upper fuel filter and it is full of fuel, the fuel pump does its normal buzzing when the key is turned on. I even checked the emergency shut off switch for the fuel pump and it was fine. At the moment I am charging both batteries... they were draining because of all the cranking. I think I will check the FICM with a multi meter when the batteries are good and charged.. Seems weird to be running fine with no hints of issues then all of a sudden its dead.
View 14 Replies
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 Replies
I just bought a new to me, 2005 ford f-350 6.0L turbo diesel with 220,000 miles. It has an EGR delete, and aftermarket intake and exhaust. I am having power loss issues, and cold start issues, and judging from these symptoms, I figured it was the FICM. I thought it had to be the FICM. As per the tech folder on this site, I tested the FICM. I first learned that I have one of the Bullet proof FICM's, and when I tested it (3 times) it read between 57.5 and 58V. I conducted this test three times both with just turning the key, and with the truck running. I then took the truck into Ford, and they gave me a list of all of the codes the truck threw:
P0611
p0113
p0405
p0671
p0673
p0675
p0677
p0341
I researched all of these codes, and it seems to point to the FICM, but Ford stated they pulled a reading of 54.5v. The tech then told me that the upgraded bullet proof FICM probably ruined my injectors, because my injectors we not upgraded. Is this True?
Even though my FICM is above the low limit for voltage, can it still be going out? I am taking the truck in to have the batteries load tested, so I will know if they are contributing to my FICM failing.
View 13 Replies
So I have an '03 6.0 with 151000 and change. I go out to light her off in the morning and she fires quick and easy. Idles well and no complaints. But when hot shes sluggish to start. Now it's not what I would call a typical hard start considering I've watched videos on YouTube and guys are having a lot harder of a time then me getting theirs started. It's just not the same as cold it almost sounds like it's lacking fuel cause it starts real low after fire then with a couple revolutions it perks up. And this is without the key still in it. Again no idle or running issues at all. I've been trying to see if it could be my ipr? My ficm is new and never gets below 47V but idk what it is.
View 14 Replies
Been having an issue every once in a while for the past 3-4 weeks.
Truck will not start when cranking sometimes (has happened 4 different times as of today), then I will stop cranking, and retry and it will fire up.
Of course when I try to replicate the no start, it won't replicate. So from here on out I will make sure my Torque Pro connects to the BAXF before cranking.
I know to look at the HPOP psi number.
I need to know the other parameters to look at during cranking. I am suspecting the STC, dummy plugs, or stand pipes with a leak by or drain down of oil.
View 7 Replies
I've got a leak that appears to be coming from the secondary fuel filter housing (the one in the engine compartment)... It's not coming from the filter, but from the side, where there are 4 allen bolts that attach a fitting to the side of the housing...Can I change out the gasket for that piece? I've already tightened the bolts, but the leak persists.
View 14 Replies
