Ford 6.0L Power Stroke Diesel :: Brief Loss Of Power When Accelerate While Driving - Bad Injector?
Apr 26, 2015
Occasionally when I'm driving, I'll accelerate and get a brief loss of power, then it'll pick back up, followed by a puff of white/blue smoke. This usually happens when the oil is over 120*, but not quite to full operating temps. It doesn't happen every time either. Only 3 times in the past week. Otherwise, there is a very faint haze of white smoke that seems to be constant. It is very difficult to see unless against a dark background. Oil level is good, I check it once a week, no rising or lowering levels.
I pulled the EGR yesterday, all good, although a tad dirty. Cleaned up no problem. Haven't had a chance to do a bubble test yet. There are some DTCs, but I can't remember off the top of my head what they were. I'm about to go clean the inside of the truck, so I will pull those and update in a few minutes.
Truck has about 148,500 miles.
Torque Pro lists these codes: C1145, P0299, P0677
View 7 Replies
Advertisement
My f350 6.0 has seem to have lost its power, while I was driving home it would only accelerate at one constant speed, and driving up hill it would not accelerate at all, I also noticed an elevated exhaust temperature.. There are no warning lights or dash lights indicating any problem.....
View 8 Replies
I was driving and went to accelerate quickly and had no power, checked the boost gauge and it had very low boost. Continued like this the rest of the drive, all gauges normal, no check engine light, not towing or hot. Got home then next time out it was back to normal.
Someting to be concerned about? Or just a computer hiccup. Truck is '13 with 66k.
View 3 Replies
So I have a no start on my 6.0. I was driving and went to accelerate and had no power, pulled off of the road and was idling rough, I checked for fuel leaks-none. I put it in drive and engine cut off and wouldn't start again, changed the ICP (threw a code) still nothing, FICM is good, ICP is 950 psi at cranking, IPR is only at 54%. I'm at a loss of what to do next besides looking at the IPR, and I do not have the equipment for a leak test.
View 14 Replies
I have searched and the only thing close is bad sensor for water in fuel light but it does not say they lost power. When driving or leaving from a stopped position, if I put any extra load on engine by pressing on accelerator pedal fast the water in fuel light comes on and the glow plug light comes on and the truck loses all power. Not 12V power just engine power. I have to let off the pedal and the lights go out and I have power again. Until I press the pedal hard again and it does it again. I have drained the filters and replaced them and still the same.
View 14 Replies
I have an 07 6.0 with 400,000 miles. Has been a great truck with no major problems. Before I started the work I had 3 bad injectors, running rough and the oil/ coolant temp just outside of 15 degrees. So I tour her down and replaced head gaskets, installed arp studs,all new injectors,all new glow plugs and new oil cooler. Ran great for a couple days. Then when driving to work lost power on and off for a few miles then completely gone could only go 10 miles an hour. I checked codes and there was the under boost code witch has been on there for a while and I forget the other code but it was for the ipr valve so I replaced the valve and right after still the same but that code went away and the p0470 popped up. So I cleaned out the ep sensor tube and replaced the valve. After several miles she now runs great but now I'm getting a little puff of white smoke when I take off and not every time and mainly when I take off some what quick. All codes are gone expect the under boost. I have an egr delete already.
View 7 Replies
I was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 Replies
I have a 04 F30 4x4 with a sick 6.0 power stroke. It has 230k on the mileage and ran good. I was driving at speed when she started missing like it had lost an injector and loosing power. The RPM's dropped under 1000 so I had to pull over off the highway. When i pulled over and put it in park it shutoff. Tried several times to get to start but after 10 minutes it started up. I drove about 2 miles and it started the same process. This went on 2 more times before I was able to finally limp home the 40 miles.
It never shut off again but ran very poorly. I put a new valve in and when I tried to start it just mad a pound clunking/clacking noise. The repair shop put a starter in it because it had stopped engaging and was going to ruin the fly wheel. I looked at it and it was eaten up pretty bad from trying to get the engine to turn over. So now all it will do is a single clunk and will not turn over. He says it could be a bad injector that flooded a cylinder or blown up in the bottom end. He did take serpentine off and still no go.
View 3 Replies
Ok yesterday while driving my truck the glow plug light came on couple times and lost power but the light would turn off and power came back. It has done this before and it was the injector harness grounding out on the engine. I replaced that last time. I checked over the knew one and did not see any chaffing on the harness.
Now this morning I go outside to start it and I can hear my fuel pump and vacuum pump but injectors wouldn't cycle. It has also done this before but I could never figure out why. Last time I tore into it checking through my wiring harness and couldn't find anything. When I put it back together it started fine.
View 10 Replies
I filled up at the same fuel station I've filled up at for 6 months, never had a problem. I just bought a 6 liter and put some injector cleaner in on the last fill up. Ever since then, it's been running really rough and missing when cold, and even when it's warm if I really lay into it, it'll pop and sputter. The fuel in water lights been on since I bought it. I think I have a bad sensor, because it was running fine until I put that cleaner in. Since its been running rough I put in new fuel filters and drained the fuel water separator, which only had fuel in it. I don't really know what it could be, but I'm 99% sure it's an injector issue since it started only after I put fuel treatment in.
View 8 Replies
I've got an injector #7 misfire, so it looks like I'll be replacing my first stick since the warranty expired.
Does the injector from Ford come with the copper crush washer? Will I need to buy anything else except for the oring kit?
where is injector 7? edit: it looks like number 7 is the farthest back on the passenger side. Great! I get to do the hard side.
AE pics below. I've never understood the Power Balance test, it most always looks the same. Seems to me something should look odd with #7, but I'm just not seeing it. As I shut down each cylinder one at a time, all made the engine run noticeably rougher, except it was only a subtle difference when shutting down #7. So that plus the code pointing at #7 lead me to believe that #7 is my culprit.
View 14 Replies
Is there a difference between the two harness #'s here besides the first number:
3C3z9d930aa
4C3z9d930aa
Are they the same part? Is one for a different model truck than the other?
View 7 Replies
My 2005 F-250 does not have power when the engine is cold. When the engine warms up then it seems fine. I believe that the fuel injectors need replacement. I was told that one cannot get new injectors. They are all re-manufactured. Is this correct?
View 14 Replies
I may have to replace fuel injector #8 on my 2004 6.0. Aside from doing brakes and rotors, I don't have any experience working on my truck.
Side note- this is the second injector to go bad in the past few months. Ford also wanted to replace the HFCM, so I'll be doing that as well.
View 7 Replies
What the size of the internal oring is? So far I have had no luck finding the size. I'm looking for the lower housing to body oring.
View 14 Replies
My 6.0 keeps trying starts on a regular bases. I was told it was a week injector by mechanic so we replaced that one and bought a new starter. Within 2 days it had fried that one also. We did check batteries and they tested good even put them in another dismal and drive them for a week. Mechanic told us we need to put another injector in it. But I don't see how a injector can fry the starter.
View 12 Replies
I have a 2004 F250 early build over 260K miles on it. After taking a trip out west Texas and back I noticed my truck starts to jerk a lot around the 50 to 60 mph range under moderate throttle. Getting a contribution code on #6. FICM voltage stays over 47v during KOEO and startup. Took an inferred thermometer and even after truck is at operating temp #6 is reading about 3 degrees cooler then the others.
When cranking the engine everything sounds smooth but startups are getting harder. Usually let it idle for a few minutes before taking off on cold start but I am having to let it warm up longer before I can get any power. Did a bubble test and passed and oil level hasnt changed. Fuel mileage has been sucking bad also. Safe to assume the injector is shot and needs replaced? Use Delo 5W-40 Syn every change with motorcraft filters.
View 4 Replies
I have been getting about a 1-2 second power loss while driving. happened last friday when at a stop light, pressed the pedal and started to go then it dropped out for a second or two and then caught right back up. only cut out twice in 10 minutes then ran fine for another week. This friday oddly enough , it happened again while driving down the road. happened about 5 different times in 10 minutes, then back to normal. I replaced the passenger uvch with dorman, but not driver side a couple of months ago . Does this sound like the other uvch, or tps?
View 6 Replies
I have a 2004 F-250 with a 6.0 and am having a serious issue. The truck has about 240,000 miles and has been great until now. About a week ago the truck was running great and had plenty of power. I decided to wash it with my pressure washer (did not spray under the hood, however I did spray in the front wheel wells and underneath the truck). About 5 minutes after washing the truck, I took it out for a drive and noticed when I really got on the accelerator the truck would not want to try harder and motor got very quiet. Really all you could hear was the turbo whistling. Over this past week the problem has gradually gotten worse... a few days ago I had to feather the pedal in order to go up hills. If I gave it more than about 1/4 inch of accelerator, the motor once again would get quiet and the truck would start to slow down and would not want to work.
However, if I let up and only gave it a small amount of accelerator, the motor would sound normal again and it would pull up the hill. Today, I can do nothing more than idle back and forth in the driveway because the motor gets quiet and the turbo winds up if you give it even the slightest amount of accelerator. I have no idea if it's a coincidence that this happened after washing the truck, or if maybe there was a sensor that was rotted and about to die and I finished the job with the pressure washer. I already replaced the egr valve and have been running tons of Howes diesel conditioner and anti gel through it. The injectors were replaced about 50,000 miles ago so I'd hate to think it was them. The truck doesn't smoke at all either.
View 13 Replies
My issue can be while driving with cruise on, or accelerating, the truck just losses power, then recovers. At idle, the rpm can, but not always, fluctuate.
There is no "misfire" when it happens, but it just falls on its face. I have NO diagnostic tools, and my injectors are not stock, so I am unable to unplug my DP.
My thoughts are to unplug the ICP and give that a shot? Meanwhile, I will put in a order for a elm327
View 14 Replies
I have a 2005 6.0. I just got done doing the HPOP seals, injector o-rings, stand pipes and dummy plugs. I have drove the truck 600 miles since the work with no problems other than a wiring issue I got fixed...
I was driving at highway speeds, and all of a sudden I lost power and got a shake when trying to accelerate. I pulled over and turned it off, and when I went to restart it I got nothing at first, then it went to what seemed like a partial crank followed by a thud. So I'm thinking I just hydro locked it. I waited a few mins and tried again, and it started but had a few knocks for 15 seconds or so, then it ran rough with smoke pouring out of the exhaust (grey then turned kinda white).
I the only codes I have are for the egr which I've had unplugged for a long time, and a glow plug code, but when I started it back up, I had no codes. I'm baffled. I did notice I have oil on my oil filter housing at the cap, a little oil had slung on to my wire harness and my intake. I don't even know where to begin!
View 14 Replies
