Ford 6.0L Power Stroke Diesel :: Blown Fuse Causing Lack Of Power To OBD Port?
Jan 4, 2016
Blown fuse causing a lack of power to the OBD port?
I just got my Kiwi2 BT OBD2 adapter and was hoping to start diagnosing my truck, but the adapter won't power on while connected to the truck.
I pulled and visually inspected fuse #12, I also verified power to the cigarette lighter plug and the accessory 12v power outlet.
The adapter powered up with no problem when I connected to a co-worker's Tacoma.
View 14 Replies
Advertisement
Ihave a 2008 E 350 6.0 , while driving i hit a small pothole no big deal the van stops running and coasts to the side of the road. get her towed. The dash lights show the PATS is engaged so it is no start no crank.
The 30 amp fuse PCM power relay is blown. when i replace it it blows as soon as i turn the key. im checking for wire chafing but so far have found none.
View 2 Replies
I just bought the batteries I was asking about in this posting. Bought them at auto zone on my lunch hour today, they swapped them out right there in the lot, no problems. Watched carefully to make sure terminals were not crossed, etc. When I came out of work a few hours later, the #20 fuse for door locks was blown. I chalked it up to the battery change, and put a new fuse back when I got home. I come out an hour later to leave, and the fuse is blown again. I have not replaced it again, need to go get more of the proper amp rating.
No other changes to the truck other than the battery replacement. And that's the only anomaly. No other problems, nothing. Getting ready to head cross-country on a skiing trip, this Friday, so there really is no time to get to the dealer to get this looked at.
View 6 Replies
I was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 Replies
I have a 2003 with 150k miles. My 6.0 has black smoke and can barely crawl up a hill. Dealership is 30 days out for an appt. Air filter, oil change, alternator, and batteries are new. I removed the EGR valve and cleaned, but the valve seat is not perfect. I can see 20 to 30 mil gap around half of the seat. Is this ok or will that little gap cause this?
Hoses all look good. No alarm lights. I have no diagnostic tool but I can use a meter well. It did have an airbag light but I found the fuse missing and replaced it. The air filter alarm switch fell apart but I bypassed it till I get new part. No alarm lights now.
View 14 Replies
While I'm cursing at highway speed everything is fine. But when u punch it it pass someone it's like I actually slow down, same from a red light. I've got a livewire programmer in it and this problem is somewhat new. It just seems to keep getting worse, I was going up a hill on the interstate this morning and at 2800 rpms I was actually slowing down. I'm not sure if the fuel pump is going out or if the transmission is slipping or what.
View 7 Replies
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 Replies
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 Replies
My 2007 6.0 has a really rough (almost 'miss') during cold start up. After 5 seconds or so, it smooths back out and sounds normal. Until gauge reaches normal operating temp - there is a surge/lack of power during light acceleration. I also hear a frequent compressor coming on and running for a while which I am contributing to a possible vacuum leak. Maintenance is always done on time and I've already had a few costly repairs (both internally as well as externally) on the engine. I usually always wait for the glow-plug indicator to turn off before cranking the engine and let it idle for 5-10 minutes prior to driving it. Once the vehicle climbs to normal temp. everything seems to be fine but the compressor still comes back on every so often.IS it worth simply replacing the vacuum canister located behind the passenger side battery - or should I find someone to hook up a diagnostic unit first?
View 5 Replies
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
View 6 Replies
So the other day my 20amp maxi fuse for my fuel pump decided to blow, put a new one in & everything has been going good since. Is it just a fluke or is this an indication my pump is going out? I inspected wires off the pump & connections for corrosion & that's good, fuel filter is also new about 2 months ago & I always run #1 diesel with a little additive in the winter.
View 1 Replies
So I am not sure exactly what is going on with my truck. It is a 2004 F250 has a 6.0 L. Sometimes when I take off from a stop the truck has no power and blows some black smoke. Then the turbo kicks in and all is fine. It comes and goes when it pleases no matter the temperature. What started happening is when I drive it a steady pace on the highway sometimes the turbo gets quieter and louder and quieter and louder sometimes when it gets quieter I see a little bit of black coming out of the tailpipe. Sometimes it doesn't do it at all. Also sometimes when I let off the gas the truck sounds like it's trying to laugh at me like a wastegate is fluttering.
View 10 Replies
My 03 5.4 the obd2 port isnt working i have tried 4 bluetooth adapters and a snap on scanner and nothing will connect to the ecm. im having problems and trying to read codes my check engine light isnt on but that don't mean anything. my truck is running really rich and blows a little bit black smoke when i rev it up after its been idling a few min and getting horrible gas mileage again. yesterday i went to start it and i had to crank on it 4 time before it finally started and then when i reved it up it almost died on the way back down but it caught itself. then today i go out and it starts right up and runs fine but its still running rich but i still cant get an obd2 adapter to connect to the ecm. I checked the fuse and its not blown my cigarette plug and the power port both work. i really dont know where to start in trying to figure out this problem. Right now iI don't really want to take it to a shop right now.
View 4 Replies
Am i correct in starting to look into why I can't hook a scanner or Torque Pro bluetooth up to my truck and starting with blown Cig lighter fuse? (Cig lighter doesnt work, power port does)
View 1 Replies
I have a 2001 f350 dually diesel, I was driving it with no problem and all of the Sudden it die when I was checking the problem I not that the fuse for the diesel pump was blown immediately I replaced it and as soon I turn the key on it blew it right away I fol the wires from the pump to the fuse box and there is no wires grounding so maybe I can get a little bit of info to find the source of the problem
View 1 Replies
Well, since I replaced the MAP hose a few weeks ago the old girl has been running fine. Until yesterday. I was leaving work and she had low boost, less than 10PSI, and as I passed by a parked tractor trailer I could hear the sound of high pressure air escaping because I had my window rolled down.
So today I checked it out. I found three possible leaks spots, BUT no "smoking gun". Take a look at the pics. The damage you are seeing is on the outside of the hot side boot at the turbo and the bottom of the cold side CAC tube. The cracks don't appear to penetrate to the inside. Could these still be possible leak sites? IDK.
I'm going to order replacements anyway. Ford wants WAY to much for these parts. I checked the MAP hose and it is just like new from several weeks ago. Also, I inspected the inter-cooler as best that I can without removing it. I don't see any issues with the tanks or the tank-to-core mounting. It all looks normal. If it does fail where does it normally fail at?
View 14 Replies
I've been having issue with my truck lacking boost over the past month or so. The psi levels are normal in the morning when I start it up cold, the problem almost always occurs at start-up when the truck is somewhat warm and has been sitting for an hour or more after use. I've had boost levels at idle from -0.14psi to -0.56psi and as low as -1.2psi when driving as the problem is occurring, but it eventually kicks on and goes to normal levels after several minutes of driving. After originally taking the truck to a local diesel mechanic I was told it had EGR codes and they recommended installing an SCT tuner and cleaning the EGR valve to solve the problem. I had them install an SCT 5015 tuner and clean the valve but I've still been having the problems with boost.
View 2 Replies
I purchased 2011 F250 King Ranch Edition about 3 months ago. I'm loving the truck and not had any issues until 3 weeks ago. I locked the truck as usual using the key Fob, and upon returning to the truck, I noticed the doors weren't locked. After some brief trouble shooting, I discovered the the fuse was blown that according to the manual controls just the power door locks. I thought it was strange that a new truck would be popping a fuse so I replaced it...a couple of days later it blew again. This time I was locking the truck with the door key pad. I took it to the dealership and they checked it over and said they replaced the fuse and cycled it numerous times but could not reproduce the problem. The told me that they even put a call in to the Ford engineers and they said check the key pad for water intrusion. The dealership told me they disassembled the key pad and found nothing wrong....lock and unlocked the door some more and the fuse would not blow. I picked the truck up four days ago and the fuse blew again last night. Everything else works...alarm sets and goes off if any of the doors are opened. The only thing that I can find that doesn't work when the fuse is blown is the remote start.
View 14 Replies
I just purchased a crashed 2011 F350 and trying to figure out why there is no power to the fuse box under the hood. I have power to the cab lights,cluster and so on but will not turn over. Checked the fuse box under the hood and seems to be not power to it. Is there a main fuse somewhere or what do you think??
View 7 Replies
I have this problem code P0405. At fist it come up with a turbo under boost. I have replaced the Turbo and egr valve and I still have the P0405. I did notice a oily residual in the port for the egr valve I see no deference in coolant. She idles good I just have no power when I put it in gear to move.
View 3 Replies
So at low idle my fan is running like 230rpm according to torque pro. I think this is causimg my ect to rise when at idle. It's usually 192-194* but if I'm idling in traffic or just In general (after it's been running a while) it climbs to 195.8, 197, 199.2, 201, 203, 204.8. Haven't seen it get higher than the 204. Now once I get moving again it will lower back down. I can see where I have flow into the degas not to mention the water pump is new. Could my low fan speed be my issue? I believe it should be more around 500rpm at low idle.
View 14 Replies
